Window-of-Opportunity for In Situ Burning

This paper is a summary of the fundamentals that influence the window-of-opportunity for in situ burning of oil at sea. It is a discussion of the variables and factors that influence the capabilities and limitations of in situ burning of oil. This includes the requirements for ignition and sustained burning and the factors that influence the quantity of residue and burn efficiency and the use of emulsion breakers.     

Introduction/Overview to In Situ Burning of Oil Spills

In situ burning is an oil spill response technique or tool that involves the controlled ignition and burning of the oil at or near the spill site on the surface of the water or in a marsh (see Lindau et al., this volume). Although controversial, burning has been shown on several recent occasions to be an appropriate oil spill countermeasure. When used early in a spill before the oil weathers and releases its volatile components, burning can remove oil from the waters surface very efficiently and at very high rates. Removal efficiencies for thick slicks can easily exceed 95% (Advanced In Situ Burn Course, Spiltec, Woodinville, WA, 1997). In situ burning offers a logistically simple, rapid, inexpensive and if controlled a relatively safe means for reducing the environmental impacts of an oil spill. Because burning rapidly changes large quantities of oil into its primary combustion products (water and carbon dioxide), the need for collection, storage, transport and disposal of recovered material is greatly reduced. The use of towed fire containment boom to capture, thicken and isolate a portion of a spill, followed by ignition, is far less complex than the operations involved in mechanical recovery, transfer, storage, treatment and disposal (The Science, Technology, and Effects of Controlled Burning of Oil Spills at Sea, Marine Spill Response Corporation, Washington, DC, 1994).However, there is a limited window-of-opportunity (or time period of effectiveness) to conduct successful burn operations. The type of oil spilled, prevailing meteorological and oceanographic (environmental) conditions and the time it takes for the oil to emulsify define the window (see Buist, this volume and Nordvik et al., this volume). Once spilled, oil begins to form a stable emulsion: when the water content exceeds 25% most slicks are unignitable. In situ burning is being viewed with renewed interest as a response tool in high latitude waters where other techniques may not be possible or advisable due to the physical environment (extreme low temperatures, ice-infested waters), or the remoteness of the impacted area. Additionally, the magnitude of the spill may quickly overwhelm the deployed equipment necessitating the consideration of other techniques in the overall response strategy (The Science, Technology, and Effects of Controlled Burning of Oil Spills at Sea, Marine Spill Response Corporation, Washington, DC, 1994; Proceedings of the In Situ Burning of Oil Spills Workshop. NIST. SP934. MMS. 1998, p. 31; Basics of Oil Spill Cleanup, Lewis Publishers, Washington, DC, 2001, p. 233). This paper brings together the current knowledge on in situ burning and is an effort to gain regulatory acceptance for this promising oil spill response tool.     

Ignition,flame spread and mass burning characteristics of liquid fuels on a water bed

An experimental technique has been developed to study systematically the ignition, flame spread and mass burning characteristics of liquid fuels spilled on a water bed. The final objective of this work is to provide a tool that will serve to assess a fuel's ease of ignition, spread and sustaining a flame, thus, helping to better define the combustion parameters that affect in situ burning of oil spills.     

Marsh Sensitivity to Burning of Applied Crude Oil

This research note summarizes Spartina alterniflora and Sagittaria lancifolia sensitivity to oiling and in situ burning of applied oil. Experimental plots (2.4 m × 2.4 m × 0.6 m) were constructed in salt and freshwater marsh habitats and South Louisiana Crude (SLC) applied (2 l m⁻²) to stems and leaves of marsh plants of oil and oil/burn treatment plots. Burning was initiated mid-August when winds were calm and a 15-25 cm floodwater layer covered the marsh substrate. Vegetative responses (stem density, height, carbon assimilation and biomass production) were measured for approximately one year following the in situ burns. Application of oil and burning of SLC only had short-term detrimental effects on salt and freshwater marsh vegetation. About one year after burns, vegetative responses measured in oiled and oiled/burned plots approached or exceeded control (no oil or burn) values. Field results suggest, under our experimental conditions, in situ burning of spilled oil in S. alterniflora and S. lancifolia marshes may be a remediation operation to consider.     

Determination of the Burning Characteristics of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is characterized by three distinct processes, ignition, flame spread and burning rate. Although all three processes are important, ignition and burning rate are critical. The former, because it defines the potential to burn and the latter because of the inherent possibility of boilover. Burning rate is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil spill. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). Ignition has been studied to provide a tool that will serve to assess a fuels ease to ignite under conditions that are representative of oil spills. Two different techniques are used, piloted ignition when the fuel is exposed to a radiant heat flux and flash point as measured by the ASTM D56 Tag Closed Cup Test. Two different crude oils were used for these experiments, ANS and Cook Inlet. Crude oils were tested in their natural state and at different levels of weathering, showing that piloted ignition and flash point are strong functions of weathering level.     

In Situ Burning of Spilled Oil in Freshwater Inland Regions of the United States

In situ burning is being utilized in the United States to remove oil from inland oil spills, usually when physical recovery is not feasible. Studies have found that habitats may recover from the effects of burning in less than a year under optimal conditions but recovery may take much longer. Policies authorizing the use of in situ burning across the US are very inconsistent. Some states use it routinely, but others do not allow it. Inland in situ burning can be a useful response tool and the federal government needs to issue more guidance to the states. Responders also need to collect more data on the environmental impacts of burning.     

Environmental Effects of In Situ Burning of Oil Spills in Inland and Upland Habitats

In situ burning of inland and upland habitats is an alternative oil spill cleanup technique that, when used appropriately, may be more environmentally acceptable than intrusive manual, mechanical, and chemical treatments. There have been few published reports documenting the environmental effects of in situ burning in inland and upland habitats. Thus, this study, sponsored by the American Petroleum Institute, used two approaches to increase the knowledge base and improve the appropriate use of in situ burning: (1) detailed review of published and unpublished in situ burn case histories for inland and upland spills; and (2) summaries of fire effects and other information from the literature on fire ecology and prescribed burning. Thirty-one case histories were summarized to identify the state of the practice concerning the reasons for burning, favorable conditions for burning, and evaluations of burn effects. The fire ecology and effects summaries included information from the extensive knowledge base surrounding wildfire and prescribed burning (without oil) as a natural resource management tool, as well as fire tolerance and burning considerations for dominant vegetation types of the United States. Results from these two approaches should improve the application of in situ burning for inland and upland spills.     

A study on the effects of oil fires on fire booms employed during the in situ burning of oil

For over 10 years scientists have studied the effects of in situ burning of oil on air and water quality and potential related health issues. The recent Newfoundland Offshore Burn experiment, conducted by Environment Canada, was the culmination of several years of work. The results of this experiment found that ‘emissions from the in situ oil fire were lower than expected and all compounds and parameters measured were below health concerns at 150 m from the fire’ (The Newfoundland Offshore Burn Experiment—NOBE, Preliminary Results of Emissions Measurement). Polyaromatic Hydrocarbons (PAHs) were found to be lower in the soot generated from the fire than in the starting oil prior to the fire. The conclusion reached was that the environmental benefits resulting from the burning of oil spills far outweigh the potential air pollution caused from the smoke. These findings now open the door on the use of in situ burning of oil as a major tool to be used to mitigate environmental damage from oil spills.As a result of these and other test findings, Region 6 of the Regional Response Team (made up of the U.S. Coast Guard, The Minerals Management Service, The Department of Environmental Quality, The U.S. Environmental Protection Agency, and other state and federal agencies) had pre-approved the use of in situ burning of oil spills for offshore Louisiana and Texas. Other parts of the country and other countries are evaluating the use of in situ burning to combat oil spills. Now that the scientific community has weighed the environmental costs and benefits of in situ burning it is time to address the operational and procedural issues.     

In situ burning of emulsions R&D in Norway

SINTEF Applied Chemistry has been working in the field of in situ burning since 1988, beginning with the first open water testing of the 3M fire proof boom which took place on Spitsbergen. In recent years, the focus of SINTEF's research activities in this area has been on the burning of emulsions. An experimental programme was initiated by NOFO in 1990 to study the in situ burning of water-in-oil (w/o) emulsions, as part of a wider NOFO programme ‘Oil spill contingency in Northern and Arctic waters’ (ONA). The research conducted under this programme has addressed many areas of in situ burning including:

• •• study of processes governing burning emulsions
• •• development of ignition techniques for emulsions
• •• effect of environmental conditions on burning
• •• burning crude oil and emulsions in broken ice
• •• uncontained burning of crude oil and emulsions.

     

The technology windows-of-opportunity for marine oil spill response as related to oil weathering and operations

This paper identifies and estimates time periods as ‘windows-of-opportunity’ where specific response methods, technologies, equipment, or products are more effective in clean-up operations for several oils. These windows have been estimated utilizing oil weathering and technology performance data as tools to optimize effectiveness in marine oil spill response decision-making. The windows will also provide data for action or no-action alternatives. Crude oils and oil products differ greatly in physical and chemical properties, and these properties tend to change significantly during and after a spill with oil aging (weathering). Such properties have a direct bearing on oil recovery operations, influencing the selection of response methods and technologies applicable for clean up, including their effectiveness and capacity, which can influence the time and cost of operations and the effects on natural resources.The changes and variations in physical and chemical properties over time can be modeled using data from weathering studies of specific oils. When combined with performance data for various equipment and materials, tested over a range of weathering stages of oils, windows-of-opportunity can be estimated for spill response decision-making. Under experimental conditions discussed in this paper, windows-of-opportunity have been identified and estimated for four oils (for which data are available) under a given set of representative environmental conditions. These ‘generic’ windows have been delineated for the general categories of spill response namely: (1) dispersants, (2) in situ burning, (3) booms, (4) skimmers, (5) sorbents, and (6) oil-water separators. To estimate windows-of-opportunity for the above technologies (except booms), the IKU Oil Weathering Model was utilized to predict relationships—with 5 m s⁻¹ wind speed and seawater temperatures of 15°C.The window-of-opportunity for the dispersant (Corexit 9527^®) with Alaska North Slope (ANS) oil was estimated from laboratory data to be the first 26 h. A period of ‘reduced’ dispersibility, was estimated to last from 26–120 h. The oil was considered to be no longer dispersible if treated for the first time after 120 h. The most effective time window for dispersing Bonnic Light was 0–2 h, the time period of reduced dispersibility was 2–4 h, and after 4 h the oil was estimated to be no longer dispersible. These windows-of-opportunity are based on the most effective use of a dispersant estimated from laboratory dispersant effectiveness studies using fresh and weathered oils. Laboratory dispersant effectiveness data cannot be directly utilized to predict dispersant performance during spill response, however, laboratory results are of value for estimating viscosity and pour point limitations and for guiding the selection of an appropriate product during contingency planning and response. In addition, the window of opportunity for a dispersant may be lengthened if the dispersant contains an emulsion breaking agent or multiple applications of dispersant are utilized. Therefore, a long-term emulsion breaking effect may increase the effectiveness of a dispersant and lengthen the window-of-opportunity.The window-of-opportunity of in situ burning (based upon time required for an oil to form an emulsion with 50% water content) was estimated to be approximately 0–36 h for ANS oil and 0–1 h for Bonnie Light oil after being spilled. The estimation of windows-of-opportunity for offshore booms is constrained by the fact that many booms available on the market undergo submergence at speeds of less than 2 knots. The data suggest that booms with buoyancy to weight ratios less than 8:1 may submerge at speeds within the envelope in which they could be expected to operate. This submergence is an indication of poor wave conformance, caused by reduction of freeboard and reserve net buoyancy within the range of operation. The windows-of-opportunity for two selected skimming principles (disk and brush), were estimated using modeled oil viscosity data for BCF 17 and BCF 24 in combination with experimental performance data developed as a function of viscosity. These windows were estimated to be within 3–10 h (disk skimmer) and after 10 h (brush skimmer) for BCF 17. Whereas for BCF 24, it is within 2–3 d (disk skimmer) and after 3 d (brush skimmer).For sorbents, an upper viscosity limit for an effective and practical use has in studies been found to be approximately 15,000 cP, which is the viscosity range of some Bunker C oils. Using viscosity data for the relative heavy oils, BCF 17 and BCF 24 (API gravity 17 and 24), the time windows for a sorbent (polyamine flakes) was estimated to be 0–4 and 0–10 d, respectively. With BCF 24, the effectiveness of polyamine flakes, was reduced to 50% after 36 h, although it continued to adsorb for up to 10 d. For BCF 17, the effectiveness of polyamine flakes was reduced to 50% after 12 h, although it continued to adsorb for up to 4 d. The windows-of-opportunity for several centrifuged separators based upon the time period to close the density gap between weathered oils and seawater to less than 0.025 g ml⁻¹ (which is expected to be an end-point for effective use of centrifugal separation technology), were estimated to be 0–18 (ANS) and 0–24 h (Bonnie Light) after the spill. Utilizing the windows-of-opportunity concept, the combined information from a dynamic oil weathering model and a performance technology data base can become a decision-making tool; identifying and defining the windows of effectiveness of different response methods and equipment under given environmental conditions. Specific research and development needs are identified as related to further delineation of windows-of-opportunity.     

A Numerical Simulation of an Oil Spill in Tokyo Bay

An oil spill accident happened in Tokyo Bay on 2 July 1997. About 1500 m³ of crude oil was released on the sea surface from the Japanese tanker Diamond Grace. An oil spill model is applied to simulate the fate of spilled oil. The Lagrangian discrete-parcel method is used in the model. The model considers current advection, horizontal diffusion, mechanical spreading, evaporation, dissolution and entrainment in simulating the oil slick transformation. It can calculate the time evolution of the partition of spilled oil on the water surface, in the water column and the sedimentation on the bottom. A continuous source at constant rate is set up as a tanker off the coast of Yokohama. The grid size is 1 km in the calculation domain. The residual flow simulated by a 3-D hydraulic model and observed wind data are used for advection. The simulated distribution of oil spreading agrees well with observations from satellite remote-sensing.     

Evaluating a Protocol for Testing a Fire-Resistant Oil-Spill Containment Boom

Most response plans for in situ burning of oil at sea call for the use of a fire-resistant boom to contain the oil during a burn. Presently, there is no standard method for the user of a fire-resistant boom to evaluate the anticipated performance of different booms. The ASTM F-20 committee has developed a draft standard, “Standard Guide for in situ Burning of Oil Spills on Water: Fire-Resistant Containment Boom”; however, the draft provides only general guidelines and does not specify the details of the test procedure. Utilizing the guidelines in the draft standard, a series of experiments were conducted to evaluate a protocol for testing the ability of fire-resistant booms to withstand both fire and waves.     

Second Phase Evaluation of a Protocol for Testing a Fire Resistant Oil Spill Containment Boom

Most response plans for in situ burning of oil at sea call for the use of a fire-resistant boom to contain the oil during a burn. Presently, there is no standard method for the user of fire-resistant boom to evaluate the anticipated performance of different booms. The American Standard for Testing Materials (ASTM) F-20 Committee has developed a draft standard, `Standard Guide for in situ Burning of Oil Spills on Water: Fire-Resistant Containment Boom'; however, the draft provides only general guidelines and does not specify the details of the test procedure. Utilizing the guidelines in the draft standard, a second series of experiments was conducted to evaluate a protocol for testing the ability of fire-resistant booms to withstand both fire and waves.     

The role of wind and emulsification in modelling oil spill and surface drifter trajectories

Laboratory and field data suggest that the movement of spilled oil at sea is in general a three-dimensional phenomenon in physical space, whereas trajectories of undrogued surface drifters are more susceptible to two-dimensional analysis. These conclusions are consistent with the intermittent failure of two-dimensional surface models to simulate the trajectories of spilled oil, although such models may be more successful with data from surface drifters. A physical explanation is presented, and a model that incorporates the key portions of the governing processes is described and tested against data from experimental oil spills at sea. Observations suggest that emulsified surface oil will drift down wind at speeds in excess of 3% of the windspeed. When surface turbulence drives oil subsurface for a significant fraction of time, however, net transport speeds are considerably less and significantly to the right of the wind in the northern hemisphere.     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

Hindcast of a Japan Sea oil spill

An oil spill model was applied to the Nakhodka tanker spill accident that occurred in the Japan Sea in January 1997. The amount of oil spilled was estimated to be around 5000 kl, released over 1 day. Under a 2-m wave height condition, and a 3.5% of drift factor, the model simulated the oil slick to hit the shoreline after 6 days. This was in good agreement with the observed conditions. After drifting to the shoreline, the oil slick moved northeastward with the current. In the model, the simulation where the shoreline absorbs 100% of stranded oil failed to reproduce the actual oil slick trajectory. The simulation in which oil resuspended after stranding indicated a similar trend to the actual case. Therefore, it is likely that a considerable amount of oil that hit the shoreline may have returned to the sea and moved with the current. The effects of current pattern and wind drift angle on the oil slick trajectory were also examined. It is suggested that the wind parameters were of prime importance in reproducing a realistic distribution.     

The 1993 oil spill of Tampa Bay,a scenario for burning?

This viewpoint paper considers the potential of offshore burning of oil in the recent Tampa Bay spill as a generic oil spill response option. While the oil spilled might not have been amenable to burning, the physical constraints of the spill and subsequent environmental conditions provide a scenario for future consideration of this option.     

Past in situ Burning Possibilities

This study evaluated the feasibility of conducting in situ burning (ISB) using current technology on post-1967 major oil spills over 10 000 barrels in North America and over 50 000 barrels in South America and Europe. A diverse set of 141 spills representing various combinations of parameters affecting spill responses (e.g., spill size, oil type, weather conditions, sea temperature, and geographic location) were evaluated using four “Phase I” criteria: Distance to populated area, oil weathering, logistics, and weather conditions. In Phase I, a spill that failed to meet one of the four criteria was considered an “unsuccessful” candidate for ISB. In total, 47 of the 141 spills passed the Phase I analysis. The potential effect of the plume on populated areas was the most significant of the four Phase I criteria; 59 of the 141 spills did not pass Phase I because the incident occurred near a sizable city. Spills that met all four criteria were further evaluated using a “Phase II” analysis that applied additional criteria and considered individual spill circumstances to determine if the spill should be rated as a “successful”, “marginal call”, or “unsuccessful” ISB candidate. Fourteen spills were ultimately determined successful in the Phase II analysis, and 12 were designated marginal calls.     

Emissions from mesoscale in situ oil fires: the mobile 1991 experiments

A series of 14 mesoscale burns were conducted in 1991 to study various aspects of oil burning in situ. Extensive sampling and monitoring of these burns were conducted to determine the emissions. This was done at two downwind ground stations, one upwind ground station and in the smoke plume using a blimp and a remote-controlled helicopter. Particulate samples in air were taken and analyzed for polycyclic aromatic hydrocarbons (PAHs). PAHs were found to be lower in the soot than in the starting oil. Metals in the oil were found concentrated in the residue and could not be measured in soot samples using conventional industrial hygiene sampling techniques. Particulates in the air were measured by several means and found to be greater than recommended exposure levels only up to 150 m downwind at ground level. Combustion gases including carbon dioxide, sulphur dioxide and carbon monoxide did not reach exposure level maximums. These gases were emitted over a broad area around the fire and are not directly associated with the plume trajectory. Volatile organic compound (VOCs) emissions are extensive from fires, but the levels are less than those emitted from a non-burning test spill. Over 50 compounds were identified and quantified, several at possible levels of concern up to 200 m downwind. Water under the burns was analyzed; no analytes of concern could be found at the detection levels of the methods. The burn residue was analyzed for the same compounds as the air particulate samples. The residue contained elevated amounts of metals. PAHs were at a lower concentration in the residue than in the starting oil, however there is a slight differential concentration increase in some higher molecular weight species. Overall, indications from these mesoscale trials are that emissions from in situ burning are low in comparison to other sources of emissions and result in concentrations of air contaminants that are below exposure limits beyond 500 m downwind.