A new THOR shoulder design: a comparison with volunteers, the Hybrid III, and THOR NT

OBJECTIVE: Since the shoulders are rarely seriously injured in frontal or oblique collisions, they have been given low priority in the development of frontal impact crash test dummies. The shoulder complex geometry and its kinematics are of vital importance for the overall dummy kinematics. The shoulder complex also influences the risk of the safety belt slipping off the shoulder in oblique forward collisions. The first aim of this study was to develop a new 50th percentile male THOR shoulder design, while the second was to compare the new shoulder, mounted on a THOR NT dummy, with volunteer, THOR NT, and Hybrid III range of motion and stiffness data. The third aim was to test the repeatability of the new shoulder during dynamic testing and to see how the design behaves with respect to belt slippage in a 45 degrees far-side collision. METHODS: The new 50th percentile THOR shoulder design was developed with the aid of a shell model of the seated University of Michigan Transportation Research Institute (UMTRI) 50th percentile male with coordinates for joints and bony landmarks (Schneider et al., 1983). The new shoulder design has human-like bony landmarks for the acromion and coracoid processes. The clavicle curvature and length are also made similar to that of a male human, as is the range of motion in the anterior-posterior, superior-inferior, and medial-lateral directions. The new shoulder design was manufactured and tested under the same conditions that T?rnvall et al. (2005b) used to compare the shoulder range of motion for the volunteers, Hybrid III, and THOR Alpha. The new design was also tested in two dynamic test configurations: the first was a 0 degrees full-frontal test and the second was a 45 degrees far-side test. The dummy tests were conducted with an R-16 seat with a three-point belt, the Delta V was 27.0+/-0.5 km/h and the maximum peak acceleration was approximately 14.6+/-0.5 g for each test. RESULTS: A new shoulder design with geometry close to that of humans was developed to be retrofitted to the THOR NT dummy. The results showed that the range of motion for the new shoulder complex during static loading was larger by at least a factor of three, for the maximum load (200 N/arm), than that of either the Hybrid III or the THOR NT; this means it was more similar to the volunteers' range of motion. It was observed that the THOR NT with the new shoulder did not slide out of the shoulder belt during a far-side collision. The performance of the new shoulder was reasonably repeatable and stable during both the static tests and the sled tests. CONCLUSION: A new shoulder for the THOR NT has been designed and developed, and data from static range of motion tests and sled tests indicate that the new shoulder complex has the potential to function in a more human-like manner on the THOR dummy.     

THOR dummy chest deflection response in oblique and lateral far-side sled tests

Abstract

Objective: The focus of this study is side impact. Though occupant injury assessment and protection in nearside impacts has received considerable attention and safety standards have been promulgated, field studies show that a majority of far-side occupant injuries are focused on the head and thorax. The 50th percentile male Test Device for Human Occupant Restraint (THOR) has been used in oblique and lateral far-side impact sled tests, and regional body accelerations and forces and moments recorded by load cells have been previously reported. The aim of this study is to evaluate the chestband-based deflection responses from these tests.

Methods: The 3-point belt–restrained 50th percentile male THOR dummy was seated upright in a buck consisting of a rigid flat seat, simulated center console, dashboard, far-side side door structure, and armrest. It was designed to conduct pure lateral and oblique impacts. The center console, dashboard, simulated door structure, and armrest were covered with energy-absorbing materials. A center-mounted airbag was mounted to the right side of the seat. Two 59-gage chestbands were routed on the circumference of the thorax, with the upper and lower chestbands at the level of the third and sixth ribs, respectively, following the rib geometry. Oblique and pure lateral far-side impact tests with and without airbags were conducted at 8.3 m/s. Maximum chest deflections were computed by processing temporal contours using custom software and 3 methods: Procedures paralleling human cadaver studies, using the actual anchor point location and actual alignment of the InfraRed Telescoping Rods for the Assessment of Chest Compression (IR-TRACC) in the dummy on each aspect—that is, right or left,—and using the same anchor location of the internal sensor but determining the location of the peak chest deflection on the contour confined to the aspect of the sensor; these were termed the SD, ID, and TD metrics, respectively.

Results: All deformation contours at the upper and lower thorax levels and associated peak deflections are given for all tests. Briefly, the ID metrics were the lowest in magnitude for both pure lateral and oblique modes, regardless of the presence or absence of an airbag. This was followed by the TD metric, and the SD metric produced the greatest deflections.

Conclusion: The chestbands provide a unique opportunity to compute peak deflections that parallel current IR-TRACC-type deflections and allow computation of peak deflections independent of the initial point of attachment to the rib. The differing locations of the peak deflection vectors along the rib contours for different test conditions suggest that a priori attachment is less effective. Further, varying magnitudes of the differences between ID and TD metrics underscore the difficulty in extrapolating ID outputs under different conditions: Pure lateral versus oblique, airbag presence, and thoracic levels. Deflection measurements should, therefore, not be limited to an instrument that can only track from a fixed point. For improved predictions, these results suggest the need to investigate alternative techniques, such as optical methods to improve chest deflection measurements for far-side occupant injury assessment and mitigation.     

Chest injuries of elderly postmortem human surrogates (PMHSs) under seat belt and airbag loading in frontal sled impacts: Comparison to matching THOR tests

Abstract

Objective: The goal of the study was to develop experimental chest loading conditions that would cause up to Abbreviated Injury Scale (AIS) 2 chest injuries in elderly occupants in moderate-speed frontal crashes. The new set of experimental data was also intended to be used in the benchmark of existing thoracic injury criteria in lower-speed collision conditions.

Methods: Six male elderly (age >63) postmortem human subjects (PMHS) were exposed to a 35?km/h (nominal) frontal sled impact. The test fixture consisted of a rigid seat, rigid footrest, and cable seat back. Two restraint conditions (A and B) were compared. Occupants were restrained by a force-limited (2.5?kN [A] and 2?kN [B]) seat belt and a preinflated (16?kPa [A] and 11?kPa [B]; airbag). Condition B also incorporated increased seat friction. Matching sled tests were carried out with the THOR-M dummy. Infra-red telescoping rod for the assessment of chest compression (IRTRACC) readings were used to compute chest injury risk. PMHSs were exposed to a posttest injury assessment. Tests were carried out in 2 stages, using the outcome of the first one combined with a parametric study using the THUMS model to adjust the test conditions in the second. All procedures were approved by the relevant ethics board.

Results: Restraint condition A resulted in an unexpected high number of rib fractures (fx; 10, 14, 15 fx). Under condition B, the adjustment of the relative airbag/occupant position combined with a lower airbag pressure and lower seat belt load limit resulted in a reduced pelvic excursion (85 vs. 110?mm), increased torso pitch and a substantially lower number of rib fractures (1, 0, 4 fx) as intended.

Conclusions: The predicted risk of rib fractures provided by the THOR dummy using the C_max and PC Score injury criteria were lower than the actual injuries observed in the PMHS tests (especially in restraint condition A). However, the THOR dummy was capable of discriminating between the 2 restraint scenarios. Similar results were obtained in the parametric study with the THUMS model.     

Frontal impact dummy kinematics in oblique frontal collisions: evaluation against post mortem human subject test data

OBJECTIVE: Today, a predominant percentage of vehicles involved in car crashes are exposed to oblique or frontal offset collisions. The aim of this study is to evaluate the 50th percentile male Hybrid III, THOR 99, and THOR Alpha dummies by comparing them with the corresponding kinematics of post mortem human subjects (PMHS) in this type of collision. METHODS: The PMHS data include results from oblique frontal collision tests. They include sled tests with near-side and far-side belt geometries at 15 degrees , 30 degrees , and 45 degrees angles. The test subjects were restrained with a three-point lap-shoulder belt and the Delta V was 30 km/h. RESULTS: The results from the Hybrid III and THOR 99 tests showed that, in most of the test, the head trajectories were an average of approximately 0.1 m shorter than those from equivalent PMHS. The Hybrid III and THOR 99 far-side belt geometry tests showed that the belt remained in place longer on the shoulder of the Hybrid III than on the THOR 99 and the THOR Alpha. This was probably due to a stiffer lumbar spine in the Hybrid III and to a large groove in the steel of the superior surface of the Hybrid III shoulder structure. The THOR 99 escaped from the shoulder belt about 40-50 ms earlier than the THOR Alpha. The results from the THOR Alpha tests show that the head trajectory accorded fairly well with the PMHS data, as long as the shoulder belt did not slip off the shoulder. Although the THOR Alpha shoulder escaped the shoulder belt in the 45 degrees far-side belt geometry, the PMHS did not. This may be due to the THOR Alpha shoulder design, with approximately 0.05 m smaller superior and medial shoulder range-of-motion, in combination with a relatively soft lumbar spine. CONCLUSIONS: The THOR Alpha provides head trajectories similar to those of the PMHS under these loading conditions, provided the shoulder belt remains in position on the shoulder. When the shoulder belt slipped off the dummy shoulder, the head kinematics was altered. The shoulder range-of-motion may be a contributing factor to the overall kinematics of an occupant in oblique frontal impact situations where the occupant moves in a trajectory at an angle from that of the longitudinal direction of the car.     

Rear impact responses of different sized adult Hybrid III dummies

Rear impact sled tests were conducted using 5th, 50th, and 95th percentile Hybrid III dummies to evaluate proposed injury criteria. Different head restraint height (750, 800 mm) and backset (0, 50, 100 mm) positions were used to determine axial and shear forces, bending moments, and injury criteria (NIC, N(ij), and N(km)). The time sequence to attain each parameter was also determined. Three events were identified in the response. Event I was coincident with the maximum rearward motion of the torso, Event II occurred at the time of the peak upper neck flexion moment, and Event III occurred at the time of maximum rearward motion of the head. Parameters such as backset, head restraint height, seat-head restraint interaction, and anthropometry affected impact responses. Head rotations increased with increasing backset and increasing head restraint height. However, N(ij) and N(km) did not exhibit such clear trends. The 50th percentile dummy responded with consistent injury criteria values (e.g., the magnitude of the injury criteria increased with backset increase or head restraint height decrease). However, the 5th and 95th percentile dummies did not demonstrate such trends. These findings underscore the need to include subject anthropometry in addition to seat and head restraint characteristics for better assessment of rear impact responses.     

The influence of personal protection equipment,occupant body size,and restraint system on the frontal impact responses of Hybrid III ATDs in tactical vehicles

Objective: Although advanced restraint systems, such as seat belt pretensioners and load limiters, can provide improved occupant protection in crashes, such technologies are currently not utilized in military vehicles. The design and use of military vehicles presents unique challenges to occupant safety—including differences in compartment geometry and occupant clothing and gear—that make direct application of optimal civilian restraint systems to military vehicles inappropriate. For military vehicle environments, finite element (FE) modeling can be used to assess various configurations of restraint systems and determine the optimal configuration that minimizes injury risk to the occupant. The models must, however, be validated against physical tests before implementation. The objective of this study was therefore to provide the data necessary for FE model validation by conducting sled tests using anthropomorphic test devices (ATDs). A secondary objective of this test series was to examine the influence of occupant body size (5th percentile female, 50th percentile male, and 95th percentile male), military gear (helmet/vest/tactical assault panels), seat belt type (3-point and 5-point), and advanced seat belt technologies (pretensioner and load limiter) on occupant kinematics and injury risk in frontal crashes.

Methods: In total, 20 frontal sled tests were conducted using a custom sled buck that was reconfigurable to represent both the driver and passenger compartments of a light tactical military vehicle. Tests were performed at a delta-V of 30 mph and a peak acceleration of 25 g. The sled tests used the Hybrid III 5th percentile female, 50th percentile male, and 95th percentile male ATDs outfitted with standard combat boots and advanced combat helmets. In some tests, the ATDs were outfitted with additional military gear, which included an improved outer tactical vest (IOTV), IOTV and squad automatic weapon (SAW) gunner with a tactical assault panel (TAP), or IOTV and rifleman with TAP. ATD kinematics and injury outcomes were determined for each test.

Results: Maximum excursions were generally greater in the 95th percentile male compared to the 50th percentile male ATD and in ATDs wearing TAP compared to ATDs without TAP. Pretensioners and load limiters were effective in decreasing excursions and injury measures, even when the ATD was outfitted in military gear.

Conclusions: ATD injury response and kinematics are influenced by the size of the ATD, military gear, and restraint system. This study has provided important data for validating FE models of military occupants, which can be used for design optimization of military vehicle restraint systems.     

Effect of posture on forces and moments measured in a Hybrid III ATD lower leg

Objective: Anthropomorphic test devices (ATDs) are used to assess real injury risk to occupants of vehicles during injurious events. In the lower leg, values from load cells are compared to injury criteria developed in cadaveric studies. These criteria are typically developed with the leg in a neutral posture, whereas the ATD may assume a wide range of postures during safety evaluation tests. The degree to which the initial posture of an ATD has an effect on the measured forces and moments in the lower leg is unknown.

Methods: A Hybrid III ATD lower leg was impacted in a range of postures under conditions representing a crash test, and peak axial force and adjusted tibia index injury measures were evaluated. Ankle posture was varied in 5° increments using a custom-made footplate, and dorsi/plantarflexion (20° DF to 20° PF) and in/eversion (20° IV to 5° EV) were evaluated. Tibia angle was also varied (representing knee flexion/extension) by ±10° from neutral.

Results: Peak axial force was not affected by ankle flexion or tibia angulation. Adjusted tibia index was lowest for plantarflexion, as well as for tibia angles representative of knee extension. Both peak axial force and adjusted tibia index were lowest for postures of great inversion and were highest in neutral or near-neutral postures.

Conclusions: The range of postures tested herein spanned published injury criteria and thus would have made the difference between pass and fail in a safety evaluation. In/eversion had the largest influence on injury metrics, likely due to the change in axial stiffness and altered impact durations in these postures. Results suggest increased injury risk at neutral or near-neutral postures, whereas previous cadaveric studies have suggested that in/eversion does not influence injury risk. It is unclear whether the ATD appropriately represents the natural lower leg for impacts in out-of-position testing. Great care must be taken when initially positioning ATDs for safety evaluations, because small perturbations in posture were shown herein to have large effects on the measured injury risk using this tool.     

Difference in dummy responses in matched side impact tests of vehicles with and without side airbags

Objective: Insurance Institute for Highway Safety (IIHS) high-hooded side impacts were analyzed for matched vehicle tests with and without side airbags. The comparison provides a measure of the effectiveness of side airbags in reducing biomechanical responses for near-side occupants struck by trucks, SUVs, and vans at 50 km/h.

Method: The IIHS moving deformable barrier (MDB) uses a high-hooded barrier face. It weighs 1,500 kg and impacts the driver side perpendicular to the vehicle at 50 km/h. SID IIs dummies are placed in the driver and left second-row seats. They represent fifth percentile female occupants.

IIHS tests were reviewed for matches with one test with a side airbag and another without it in 2003–2007 model year (MY) vehicles. Four side airbag systems were evaluated: (1) curtain and torso side airbags, (2) head and torso side airbag, (3) curtain side airbag, and (4) torso side airbag.

There were 24 matched IIHS vehicle tests: 13 with and without a curtain and torso side airbags, 4 with and without a head and torso side airbag, 5 with and without a side curtain airbag, and 2 with and without a torso airbag. The head, chest, and pelvis responses were compared for each match and the average difference was determined across all matches for a type of side airbag.

Results: The average reduction in head injury criterion (HIC) was 68 ± 16% (P < .001) with curtain and torso side airbags compared to the HIC without side airbags. The average HIC was 296 with curtain and torso side airbags and 1,199 without them. The viscous response (VC) was reduced 54 ± 19% (P < .005) with curtain and torso side airbags. The combined acetabulum and ilium force (7 ± 15%) and pelvic acceleration (?2 ± 17%) were essentially similar in the matched tests.

The head and torso side airbag reduced HIC by 42 ± 30% (P < .1) and VC by 32 ± 26% compared to vehicles without a side airbag. The average HIC was 397 with the side head and torso airbag compared to 729 without it. The curtain airbag and torso airbag only showed lower head responses but essentially no difference in the chest and pelvis responses.

Conclusion: The curtain and torso side airbags effectively reduced biomechanical responses for the head and chest in 50 km/h side impacts with a high-hooded deformable barrier. The reductions in the IIHS tests are directionally the same as estimated fatality reductions in field crashes reported by NHTSA for side airbags.     

Variations in occupant response with seat belt slack and anchor location during moderate frontal impacts

Both seat belt slack and anchor location are known to affect occupant excursion during high-speed frontal collisions, but their effects have not been studied at moderate collision severities. The goal of this study was to quantify how seat belt slack and anchor location affect occupant kinematics and kinetics in moderate severity frontal collisions. A Hybrid III 50th percentile male dummy was seated on a programmable sled and exposed to frontal collisions with a speed change of 17.5 km/h. The seat belt was adjusted either snugly or with 10 cm slack (distributed 60/40 between the shoulder and lap portions) and the anchor location was varied by adjusting the seat position either fully forward or rearward (seat travel = 13 cm). Accelerations and displacements of the head, T1 and pelvis were measured in the sagittal plane. Upper neck loads and knee displacements were also measured. Five trials were performed for each of the four combinations of belt adjustment (snug, slack) and anchor location (seat forward, seat rearward). For each trial, kinematic and kinetic response peaks were determined and then compared across conditions using ANOVAs. Peak displacements, accelerations and loads varied significantly with both seat belt slack and anchor location. Seat belt slack affected more parameters and had a larger effect than anchor location on most peak response parameters. Head displacements increased a similar amount between the snug/slack belt conditions and the rearward/forward anchor locations. Overall, horizontal head displacements increased from 23.8 cm in the snug-belt, rearward-anchor configuration to 33.9 cm in the slack-belt, forward-anchor configuration. These results demonstrated that analyses of occupant displacements, accelerations and loads during moderate frontal impacts should consider potential sources of seat belt slack and account for differences in seat belt anchor locations.     

A comparison of volunteers and dummy upper torso kinematics with and without shoulder belt slack in a low speed side/pre-roll environment

OBJECTIVE: The objective of this study was to compare the occupant and dummy kinematics in a low-speed lateral environment with and without shoulder belt slack. METHODS: A buck of a small European car was mounted on a side impact sled. The parameters evaluated were pulses, sitting location, and belt slack. A total of 24 tests were carried out. Three 50th-percentile male volunteers and one Hybrid III 50th-percentile male were tested. The pulses consisted of Pulse 1:+/- 0.7 g's pulse and Pulse 2: a -0.9 g pulse to simulate low-speed pre-roll/side events. Both pulses had a duration of 500 msec. RESULTS: The peak lateral head excursion was higher in the far-side occupants than in the near-side occupants. Furthermore, for the far-side volunteers, lateral head displacements were lower in the no-slack condition than in the slack condition, at 388 +/- 64 mm and 455 +/- 84 mm respectively for Pulse 1 and at 138 +/- 2 mm and 207 +/- 70 mm for Pulse 2. The timing required to reach peak lateral displacement was higher in Pulse 1 than in Pulse 2. In comparison to the volunteers, the Hybrid III dummy lateral motion was lower. The peak lateral displacement in Pulse 1 was 231 mm with slack and 194 mm without and 98 mm and 107 mm for Pulse 2, respectively. CONCLUSIONS: The results obtained in this study indicate that removing seatbelt slack would be more beneficial for far-sided occupants than near-sided. They also point to the lack of biofidelity of the Hybrid III dummy in low g lateral pulses.     

Bolted flange joints equipped with FBG sensors in industrial piping systems subjected to seismic loads

The vulnerability of major-hazard industrial plants to natural hazards has been recognized as an emergent issue whose importance is underlined by the Sendai Framework, established immediately after the Tohoku earthquake of 2011, in Japan. Hence, seismic risk analysis is of paramount importance as testified by the intense research activity that characterized the last years. In this respect, structural health monitoring can represent a valuable tool able to strongly help the decision-making phase. Along this main vein, optical fibers (OFs) represent a class of sensors able to both monitor critical conditions, as leakage of hazardous material, and activate safety barriers, if any. More precisely, optical fibers represent an economic solution, whose characteristics appear particularly suitable for dangerous environments like major-hazard plants. However, investigations relevant to their use for seismic monitoring of chemical/petrochemical plants are rather limited, especially when subject to strong dynamic excitations. As a result, this paper deals with the analysis of optical fiber Bragg gratings (FBGs) applied to bolted flange joints (BFJ) under cyclic loadings. More precisely, two experimental programs, i.e., a cyclic test on a single BFJ and a series of shaking table tests on BFJs of a multicomponent system, demonstrated the effectiveness of the proposed monitoring systems in detecting hazardous conditions and, thus, their potential use in conjunction with safety barriers.     

Experimental investigation of the effect of occupant characteristics on contemporary seat belt payout behavior in frontal impacts

Objective: The goal of this study was to investigate the influence of the occupant characteristics on seat belt force vs. payout behavior based on experiment data from different configurations in frontal impacts.

Methods: The data set reviewed consists of 58 frontal sled tests using several anthropomorphic test devices (ATDs) and postmortem human subjects (PMHS), restrained by different belt systems (standard belt, SB; force-limiting belt, FLB) at 2 impact severities (48 and 29 km/h). The seat belt behavior was characterized in terms of the shoulder belt force vs. belt payout behavior. A univariate linear regression was used to assess the factor significance of the occupant body mass or stature on the peak tension force and gross belt payout.

Results: With the SB, the seat belt behavior obtained by the ATDs exhibited similar force slopes regardless of the occupant size and impact severities, whereas those obtained by the PMHS were varied. Under the 48 km/h impact, the peak tension force and gross belt payout obtained by ATDs was highly correlated to the occupant stature (P =.03, P =.02) and body mass (P =.05, P =.04), though no statistical difference with the stature or body mass were noticed for the PMHS (peak force: P =.09, P =.42; gross payout: P =.40, P =.48). With the FLB under the 48 km/h impact, highly linear relationships were noticed between the occupant body mass and the peak tension force (R² = 0.9782) and between the gross payout and stature (R² = 0.9232) regardless of the occupant types.

Conclusions: The analysis indicated that the PMHS characteristics showed a significant influence on the belt response, whereas the belt response obtained with the ATDs was more reproducible. The potential cause included the occupant anthropometry, body mass distribution, and relative motion among body segments specific to the population variance. This study provided a primary data source to understand the biomechanical interaction of the occupant with the restraint system. Further research is necessary to consider these effects in the computational studies and optimized design of the restraint system in a more realistic manner.     

The impact of a standard enforcement safety belt law on fatalities and hospital charges in Ohio

Introduction

The purpose of this study was to analyze linked crash and hospital data to determine the effect that enactment of a standard enforcement safety belt law in Ohio would have on hospital charges and direct medical costs due to motor-vehicle crashes, focusing on the impact to the state's Medicaid system.

Method

The linkage and analysis was conducted as part of the Ohio Crash Outcome Data Evaluation System (CODES) program. Current safety belt usage in Ohio stands at 82% with its secondary enforcement safety belt law.

Results

Assuming an increase in usage to 92% through standard enforcement, over $15.3 million in medical costs to Medicaid for injuries that occur in a single year could be prevented over a 10-year period. Cumulative savings could reach more than $91.2 million during the 10-year period. In addition, 161 fatalities could have been prevented in one year had all unbelted occupants who sustained a fatal injury instead chosen to wear their safety belt.

Summary and Impact on Industry

Clearly, substantial progress can be made in reducing the number of deaths and injuries, as well as medical costs associated with motor-vehicle crashes, by strengthening safety belt laws and increasing safety belt usage in Ohio.     

Evaluation criteria for AIS 1 neck injuries in frontal impacts--a parameter study combining field data and Madymo modeling

Two situations with an expected higher AIS 1 neck injury rate in frontal impact were compared to a reference situation using a Madymo human body model in three different sitting postures and four different crash pulses. The two situations were reduced occupant weight and occupant with initial forward arm resistance, respectively. Occupant neck motion phases were identified and corresponding possible evaluation criteria were evaluated within the phases. Typical neck kinematics was seen for the two different situations. Occupants of lower weight had a more extended neck in the initial protraction phase and also a generally more pronounced upper neck link angle. Occupants with initial arm resistance had generally greater lower neck link angle at the time when the upper neck link angle was straight. No evaluation criteria reflected the anticipated AIS 1 neck injury rate consistently. In the initial protraction phase, NICmin correlated to expected injury outcome in almost half of the cases. In the protraction-flexion shift phase, Nkm, Nij, upper neck shear force and neck tension force reflected anticipated severity outcome to some extent. In the flexion phase, upper and lower neck extension correlated to anticipated AIS 1 neck injury rate only to a minor extent. The different sitting postures were more influential than the different crash pulses, emphasizing the importance of not only considering the spectra of impact severity but also differences in sitting postures in safety system development and evaluation.     

Effects of whole spine alignment patterns on neck responses in rear end impact

Objective: The aim of this study was to investigate the whole spine alignment in automotive seated postures for both genders and the effects of the spinal alignment patterns on cervical vertebral motion in rear impact using a human finite element (FE) model.

Methods: Image data for 8 female and 7 male subjects in a seated posture acquired by an upright open magnetic resonance imaging (MRI) system were utilized. Spinal alignment was determined from the centers of the vertebrae and average spinal alignment patterns for both genders were estimated by multidimensional scaling (MDS). An occupant FE model of female average size (162 cm, 62 kg; the AF 50 size model) was developed by scaling THUMS AF 05. The average spinal alignment pattern for females was implemented in the model, and model validation was made with respect to female volunteer sled test data from rear end impacts. Thereafter, the average spinal alignment pattern for males and representative spinal alignments for all subjects were implemented in the validated female model, and additional FE simulations of the sled test were conducted to investigate effects of spinal alignment patterns on cervical vertebral motion.

Results: The estimated average spinal alignment pattern was slight kyphotic, or almost straight cervical and less-kyphotic thoracic spine for the females and lordotic cervical and more pronounced kyphotic thoracic spine for the males. The AF 50 size model with the female average spinal alignment exhibited spine straightening from upper thoracic vertebra level and showed larger intervertebral angular displacements in the cervical spine than the one with the male average spinal alignment.

Conclusions: The cervical spine alignment is continuous with the thoracic spine, and a trend of the relationship between cervical spine and thoracic spinal alignment was shown in this study. Simulation results suggested that variations in thoracic spinal alignment had a potential impact on cervical spine motion as well as cervical spinal alignment in rear end impact condition.     

A Comparison of Volunteer,BioRID P3 and Hybrid III Performance in Rear Impacts

The most important tool for testing seat-systems in rear impacts is a crash test dummy. However, investigators have noted limitations of the most commonly used dummy, the Hybrid III. The BioRID I is a step closer to a biofidelic crash test dummy, but it is not user-friendly and the straightening of the thoracic spine kyphosis is smaller than that 220of humans. To reduce these problems, a new BioRID prototype was developed, the P3. It has new neck muscle substitutes, a softer thoracic spine and a softer rubber torso than does the BioRID I.

The BioRID P3 was compared with volunteer test data in a rigid and a standard seal without head restraints. The dummy kinematic performance, pressure distribution between subject and seatback, neck loads and accelerations were compared with those of ten volunteers and a Hybrid III. The BioRID P3 provided repeatable test results and its response was very similar to that of the average volunteer in rear impacts at Δv = 9 km/h.     

Effects of initial seated position in low speed rear-end impacts: a comparison with the TNO rear impact dummy (TRID) model

Injury-producing mechanisms associated with rear-end impact collision has remained a mystery not withstanding numerous investigations devoted to its scrutiny. Several criteria have been proposed to predict the injury-causing mechanism, but none have been universally accepted. The challenge lies in determining a set of testing procedures representative of real-world collisions, wherein the results obtained are not only the same as human testing, but remain consistent with various subjects and impact conditions. It is hypothesized that one of the most important considerations in the testing methodology is the effect of initial seated position (ISP) on occupant kinematics during a rear impact collision. This study involves two parts that evaluates the effects of ISP during rear-end impact. In the first part, head acceleration results of computer simulation using Hybrid III TNO rear impact dummy (TRID) are compared to physical impact testing (PIT) of humans. The second part focuses on the computer simulation using TRID to obtain different neck parameters such as NIC (Neck Injury Criterion), NIJ (Neck Injury Predictor), neck forces and moments to predict the level of neck injury such as whiplash associated disorder (WAD) during low speed rear-end impact. In PIT, a total of 17 rear-impact tests were conducted with a nominal 8-km/hour change in velocity to 5 subjects in four different seated positions comprising of a normal position (NP) and three out of positions (OOP). The first position was a NP, defined as torso against the seat back, looking straight ahead, hands on the steering wheel, and feet on the floor. The second position was a head flex position (HFP), defined as the normal position with head flexed forward approximately 20 degrees. The third position was a torso lean position (TLP), defined as the normal position with torso leaned forward approximately 10 degrees away from the seat back. Lastly, a torso lean head flex position (TLHFP), defined as the normal position with the head flexed forward approximately 20 degrees and torso leaned forward approximately 10 degrees. The head acceleration plots from PIT reveal that for the third and fourth positions (TLP and TLHFP) when the subject torso leaned forward, the peak head acceleration for the subject decreased and there was also a delay in reaching the peak. The Hybrid III-TRID anthropomorphic test dummy (ATD) was used in the same four different seated positions using computer simulation software MAthematical DYnamic MOdel (MADYMO 6.0) and the head acceleration results were compared to PIT. The comparison demonstrates that the Hybrid III-TRID ATD with MADYMO can be a reliable testing procedure during low-speed, rear-end impact for the four ISPs considered since the head acceleration plots deviated within the range of PIT head acceleration plots for different human subjects. This ensures that the second part of the study with neck injury using computer simulation results is a reliable testing procedure. It can be observed that MADYMO results have a greater error when compared to PIT when more than one OOP condition is employed as in TLHFP. All these observations would help in providing a tool to better understand the injury mechanisms and provide an accurate testing procedure for rear-end impact.