Vegetable and synthetic tannins induce hormesis/toxicity in sea urchin early development and in algal growth

Mimosa tannin and phenol-based synthetic tannin (syntan) were tested for toxicity to sea urchin (Paracentrotus lividus and Sphaerechinus granularis) early development and to marine algal growth (Dunaliella tertiolecta). Sea urchin embryogenesis was affected by vegetable tannin and syntan water extracts (VTWE and STWE) at levels >or=1mg/L. Developmental defects were significantly decreased at VTWE and STWE levels of 0.1 and 0.3mg/L when control cultures displayed suboptimal quality, i.e. <70% "viable" (normal or retarded) larvae. Fertilization success of sea urchin sperm was increased up to 0.3 mg/L STWE or VTWE, then was inhibited by increasing tannin levels (1-30 mg/L). Offspring abnormalities, following sperm exposure to VTWE or STWE, showed the same shift from hormesis to toxicity. Cell growth bioassays in D. tertiolecta exposed to VTWE or STWE (0.1-30 mg/L) showed non-linear concentration-related toxicity. Novel criteria are suggested in defining control quality that should reveal hormetic effects.     

Molecular Detection of Human Salivirus in Italy Through Monitoring of Urban Sewages

Food and Environmental Virology - Salivirus (SalV) is a newly discovered virus associated to acute gastroenteritis in humans. In Italy, its prevalence and genetic diversity is unknown. To reduce...     

Effects of nanoparticles in species of aquaculture interest

Recently, it was observed that there is an increasing application of nanoparticles (NPs) in aquaculture. Manufacturers are trying to use nano-based tools to remove the barriers about waterborne food, growth, reproduction, and culturing of species, their health, and water treatment in order to increase aquaculture production rates, being the safe-by-design approach still unapplied. We reviewed the applications of NPs in aquaculture evidencing that the way NPs are applied can be very different: some are direclty added to feed, other to water media or in aquaculture facilities. Traditional toxicity data cannot be easily used to infer on aquaculture mainly considering short-term exposure scenarios, underestimating the potential exposure of aquacultured species. The main outputs are (i) biological models are not recurrent, and in the case, testing protocols are frequently different; (ii) most data derived from toxicity studies are not specifically designed on aquaculture needs, thus contact time, exposure concentrations, and other ancillary conditions do not meet the required standard for aquaculture; (iii) short-term exposure periods are investigated mainly on species of indirect aquaculture interest, while shrimp and fish as final consumers in aquaculture plants are underinvestigated (scarce or unknown data on trophic chain transfer of NPs): little information is available about the amount of NPs accumulated within marketed organisms; (iv) how NPs present in the packaging of aquacultured products can affect their quality remained substantially unexplored. NPs in aquaculture are a challenging topic that must be developed in the near future to assure human health and environmental safety.

Open image in new window

Graphical abstract ?

     

Simulating the fate of indigenous antibiotic resistant bacteria in a mild slope wastewater polluted stream

The fate of indigenous surface-water and wastewater antibiotic resistant bacteria in a mild slope stream simulated through a hydraulic channel was investigated in outdoor experiments.The effect of(i) natural(dark) decay,(ii) sunlight,(iii) cloudy cover,(iv) adsorption to the sediment,(v) hydraulic conditions,(vi) discharge of urban wastewater treatment plant(UWTP)effluent and(vii) bacterial species(presumptive Escherichia coli and enterococci) was evaluated.Half-life time(T1/2) of E. coli under sunlight was in the range 6.48–27.7 min(initial bacterial concentration of 10~5 CFU/mL) depending on hydraulic and sunlight conditions. E. coli inactivation was quite similar in sunny and cloudy day experiments in the early 2 hr, despite of the light intensity gradient was in the range of 15–59 W/m~2; but subsequently the inactivation rate decreased in the cloudy day experiment(T1/2= 23.0 min) compared to sunny day(T_(1/2)= 17.4 min). The adsorption of bacterial cells to the sediment(biofilm) increased in the first hour and then was quite stable for the remaining experimental time. Finally, when the discharge of an UWTP effluent in the stream was simulated, the proportion of indigenous antibiotic resistant E. coli and enterococci was found to increase as the exposure time increased, thus showing a higher resistance to solar inactivation compared to the respective total populations.     

Evaluation of the effectiveness of red mud-supported catalysts in combination with ozone and TiO<Subscript>2</Subscript> in the treatment of solution containing benzene,toluene, and xylene

Ozone and a Fe²⁺/TiO₂-based catalyst were examined in the degradation of a synthetic solution of benzene toluene and xylene (BTX) in an advanced oxidation process (AOP). The catalyst beads were made from the slurry waste of aluminum production process, by inserting the TiO₂ content and subsequent calcination. The reduction of the BTX concentration load was monitored by the reduction of chemical oxygen demand (COD) and BTX concentration. Different levels were used on factors: pH, time of treatment, initial concentration of BTX, and percentage of TiO₂. The process was conducted in a bubble column reactor with the insertion of catalyst beads. A response surface methodology technique (CCD) was used to build a model based on COD reduction results. The model was optimized using the normal-boundary intersection (NBI) algorithm to maximize COD reduction and minimize the variance attributed to the process. Optimization led to COD reductions of 80% in 2 h of experiment. Correlation analysis of coefficient models from experimental data R²_adj was 0.9966, showing a good fit of model data. In the optimized conditions, the possible increase of the biodegradability ratio of the BTX solution, through the biochemical oxygen demand (BOD) and COD, was also analyzed. Under pre-treatment conditions, the BOD/COD ratio was 0.13. After the treatment, it increased to 0.56.

Open image in new window

Graphical abstract ?

     

Characterization, Fluxes and Toxicity of Leather Tanning Bath Chemicals in a Large Tanning District Area (IT)

The leather tanning industry is perceived as responsible of a significant consume of natural resources and output of wastes such as high concentration of organics, salts and heavy metals such as chromium, both in solid and liquid form as a result. Now as ever the future of tanneries strongly depends on the increase of their awareness that a sustainable industry for the future means embracing a forward-looking philosophy of the leather making process through optimal resource management within the tannery. This study reports the characterization of some chemicals used in a large tanning district area in terms of COD, BOD, aromaticity (UV₂₈₀) and double bond (UV₂₅₄) absorbance measurements, toxicity on fresh and saline water as well as terrestrial species, GC-MS scanning. The study provides a consistent set of information on tannin-associated concentration-related trends and suggests novel criteria in defining control quality for evaluating environmental impact of leather tanning industry.     

A review of plant-based coagulants for turbidity and cyanobacteria blooms removal

Environmental Science and Pollution Research - In recent years, the proliferation of Harmful Cyanobacterial Blooms (CyanoHABs) has increased with water eutrophication and climate change, impairing...