A comparison of mesh-adaptive LES with wind tunnel data for flow past buildings: Mean flows and velocity fluctuations

In this paper we address two important aspects of micro-scale urban airflow model evaluation: (a) the identification of key flow features as dictated by the physics of the problem and as captured by the simulations, and (b) the comparison of important model output parameters (mean flows and fluctuations) with experimental data. A series of mesh-adaptive large eddy simulations (LES) was carried out for the study of air flows within two intersecting street canyons with varying building configurations. The novelty of the approach lies in the combination of LES with mesh adaptivity, which allows a variable-filter length and the implementation of an anisotropic eddy-viscosity model. Both coarse and fine-mesh simulations were carried out, using single and parallel-processor systems respectively. The simulations showed clearly that the expected flow patterns such as the street canyon recirculation and the street-mouth vortices, as well as the exchange of air flow at the street intersections, can readily be captured by the mesh-adaptive LES.In addition, the detailed comparisons of mean flows and fluctuations of the resolved velocity field with the measured data showed that the simulation results agreed well with the patterns and trends of the wind tunnel measurements. In most cases the finer-mesh simulations improved considerably the accuracy of the mean flows, especially for the symmetrical configuration. The improvement in the predicted fluctuations was less obvious, with several detector locations underpredicting the measured values, although the overall comparison was also satisfactory. The typical errors for the mean flows for all three building configurations were less than 30%, whilst for the velocity fluctuations less that 40%. Both the simulated means flows and turbulence levels were generally more accurate in the streets parallel to the wind (streamwise direction) than in the streets normal to the wind.     

Walking in the Irish countryside: landowner preferences and attitudes to improved public access provision

This paper explores the attitudes of landowners across Ireland to the wider provision of public access for recreational walking using a multinomial logit model. The study also investigates the level of compensation required to improve the supply of this public good. Results indicate that 51% of landowners are not willing to provide access (non-providers), 21% are willing to provide access free of charge (free providers) and 28% seek compensation (willing providers). The findings indicate that participation by landowners in a proposed public access scheme is influenced by landowners' experience with walkers, farm type, farm insurance costs, household demographics, regional variations, opportunity cost of land and participation in other agri-environment schemes. Mean willingness-to-accept for landowners willing to facilitate improved public access for walking was found to be €0.27 per metre of walkway.     

Think global,act local: The effect of goal and mindset specificity on willingness to donate to an environmental organization

This paper investigated the effect of goal and mindset specificity on goal-related behavior in the environmental domain. Two studies demonstrated that goal-related behavior was maximized when participants focused on an abstract goal in combination with a specific mindset, or when they focused on a specific goal in combination with an abstract mindset. When goals and mindsets instead matched in terms of abstractness, goal-related behavior was reduced. Study 2 demonstrated that the effect of goal specificity on behavior was mediated by different processes in each of the mindset conditions. When mindsets were abstract, self-efficacy mediated the positive effect of specific goals on behavior; when mindsets were specific, the value of collective environmental action mediated the positive effect of abstract goals on behavior. The results are discussed in the framework of a complementarity approach. It is argued that complementarity of levels of specificity of goals and mindsets may affect behavior particularly strongly in domains where the discrepancy between the abstract and the specific is large (e.g. the environmental domain).     

Chitosan/Hydrophilic Plasticizer-Based Films: Preparation,Physicochemical and Antimicrobial Properties

The addition of plasticizers to biopolymer films is a good method for improving their physicochemical properties. The aim of this study was to evaluate the effect of chitosan (CHI) blended with two hydrophilic plasticizers glycerol (GLY) and sorbitol (SOR), at two concentrations (20 and 40 wt%) on their mechanical, thermal, barrier, structural, morphological and antimicrobial properties. The chitosan was prepared through the alkaline deacetylation of chitin obtained from fermented lactic from shrimp heads. The obtained chitosan had a degree of deacetylation (DA) of 84 ± 2.7 and a molecular weight of 136 kDa, which indicated that a good film had formed. The films composed of CHI and GLY (20 wt%) exhibited the best mechanical properties compared to the neat chitosan film. The percentage of elongation at break increase to over 700 % in the films that contained 40 % GLY, and these films also exhibited the highest values for the water vapor transmission rate (WVTR) of 79.6 ± 1.9 g m² h^?1 and a yellow color (b _o  = 17.9 ± 2.0) compared to the neat chitosan films (b _o  = 8.8 ± 0.8). For the structural properties, the Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction analyses revealed an interaction in the acetamide group and changes in the crystallinity of plasticized films. The scanning electron micrographs revealed that all formulations of the chitosan films were smooth, and that they did not contain aggregations, pores or microphase separation. The thermal analysis using differential scanning calorimetry (DSC) revealed a glass transition temperature (Tg) of 130 °C for neat chitosan film, but the addition of SOR or GLY elicited a decrease in the temperature of the peak (120 °C). In addition, the antimicrobial activity of the chitosan films was evaluated against Listeria monocytogenes, and reached a reduction of 2 log after 24 h. The plasticizer concentration of 20 % GLY is sufficient for obtaining flexible chitosan films with good mechanical properties, and it could serve as an alternative as a packaging material to reduce environmental problems associated with synthetic packaging films.     

Ambient Air Benzene Concentrations in Canada (1989-1993): Seasonal and Day of Week Variations,Trends, and Source Influences

Abstract

Since 1987, the Pollution Measurement Division of the Environmental Protection Service, Environment Canada, has operated a field program for measuring benzene in ambient air. With the cooperation of provincial and municipal environmental agencies, samples have been collected at over 30 urban and rural monitoring sites across the country. Samples are collected in evacuated canisters and analyzed by gas chromatography with a mass-selective detector. Using data from all sites, the composite average benzene concentration for Canada over the years 1989 to 1993 was 3.6 μg/m³ and the composite median was found to be 2.6 μ/m³. Benzene concentrations are highest at urban sites near major streets and at sites influenced by industrial sources. For eighteen urban and suburban trend sites (those with no nearby industrial sources), composite annual median benzene concentrations decreased by 20% between 1989 and 1993. For the same period, median benzene concentrations decreased by 33% at four trend sites with nearby industries. At most monitoring sites the parameters for benzene and CO are highly correlated; supporting the inventory estimate that most emissions of benzene are due to vehicle exhaust. For sites with nearby industrial sources of benzene, the industries are estimated to account for 35 to 70% of the benzene dose experienced at the sites. These site specific contributions are much more significant than the estimated national emissions assigned to industrial sources.     

Assessing Sorbents for Mercury Control in Coal-Combustion Flue Gas

Abstract

Sorbent injection for Hg control is one of the most promising technologies for reducing Hg emissions from power-generation facilities, particularly units that do not require wet scrubbers for SO₂ control. Since 1992, EPRI has been assessing the performance of Hg sorbents in pilot-scale systems installed at full-scale facilities. The initial tests were conducted on a 5000-acfm (142-m³/min) pilot baghouse. Screening potential sorbents at this scale required substantial resources for installation and operation and did not provide an opportunity to characterize sor-bents over a wide temperature range.

Data collected in the laboratory and in field tests indicate that sorbents are affected by flue gas composition and temperature. Tests carried out in actual flue gas at a number of power plants also have shown that sorbent performance can be site-specific. In addition, data collected at a field site often are different from data collected in the laboratory, with simulated flue gas mixed to match the major components in the site’s gas. To effectively estimate the costs of Hg sorbent systems at different plants, a measure of sorbent performance in the respective flue gases must be obtained. However, injection testing at multiple facilities with large pilot systems is not practical.

Over the past five years, fixed-bed characterization testing, modeling studies, and bench-scale injection testing have been undertaken to develop a low-cost technique to characterize sorbent performance in actual flue gas and subsequently to project normalized costs for Hg removal prior to full-scale demonstration. This article describes the techniques used and summarizes field-testing results from two plants burning Powder River Basin (PRB) coal for commercial activated carbon and several other sorbent types. Full-scale projections based on the results and data collected on larger-scale systems also are included.     

Survey of polyfluorinated chemicals (PFCs) in the atmosphere over the northeast Atlantic Ocean

High volume air sampling in Bermuda, Sable Island (Nova Scotia) and along a cruise track from the Gulf of Mexico to northeast coast of the USA, was carried out to assess air concentrations, particle-gas partitioning and transport of polyfluorinated chemicals (PFCs) in this region. Samples were collected in the summer of 2007. Targeted compounds included the neutral PFCs: fluorotelomer alcohols (FTOHs), perfluoroalkyl sulfonamides (FOSAs) and perfluoroalkyl sulfonamido ethanols (FOSEs).Among the FTOHs, 8:2 FTOH was dominant in all samples. Sum of the concentration of FTOHs (gas+particle phase) were higher in Bermuda (mean, 34 pg m^?3) compared to Sable Island (mean, 16 pg m^?3). In cruise samples, sum of FTOHs were highly variable (mean, 81 pg m^?3) reflecting contributions from land-based sources in the northeast USA with concentrations reaching as high as 156 pg m^?3.Among the FOSAs and FOSEs, MeFOSE was dominant in all samples. In Bermuda, levels of MeFOSE were exceptionally high (mean, 62 pg m^?3), exceeding the FTOHs. Sable Island samples also exhibited the dominance of MeFOSE but at a lower concentration (mean, 15 pg m^?3). MeFOSE air concentrations (pg m^?3) in cruise samples ranged from 1.6 to 73 and were not linked to land-based sources. In fact high concentrations of MeFOSE observed in Bermuda were associated with air masses that originated over the Atlantic Ocean.The partitioning to particles for 8:2 FTOH, 10:2 FTOH, MeFOSE and EtFOSE ranged from as high as 15 to 42% for cruise samples to 0.9 to 14% in Bermuda. This study provides key information for validating and developing partitioning and transport models for the PFCs.     

Geochemical and Pb isotopic evidence for sources and dispersal of metal contamination in stream sediments from the mining and smelting district of Príbram, Czech Republic

Stream sediments from the mining and smelting district of Príbram, Czech Republic, were studied to determine the degree, sources and dispersal of metal contamination using a combination of bulk metal and mineralogical determinations, sequential extractions and Pb isotopic analyses. The highest metal concentrations were found 3-4 km downstream from the main polymetallic mining site (9800 mg Pb kg(-1), 26 039 mg Zn kg(-1), 316.4 mg Cd kg(-1), 256.9 mg Cu kg(-1)). The calculated enrichment factors (EFs) confirmed the extreme degree of contamination by Pb, Zn and Cd (EF>40). Lead, Zn and Cd are bound mainly to Fe oxides and hydroxides. In the most contaminated samples Pb is also present as Pb carbonates and litharge (PbO). Lead isotopic analysis indicates that the predominant source of stream sediment contamination is historic Pb-Ag mining and primary Pb smelting (206Pb/207Pb=1.16), while the role of secondary smelting (car battery processing) is negligible.     

Breakdown products on metabolic pathway of degradation of benz[a]anthracene by a ligninolytic fungus

Cultures of the ligninolytic fungus Irpex lacteus incubated in a nutrient liquid medium degraded more than 70% of the initially applied benz[a]anthracene within 14 days. At the first step of metabolization, benz[a]anthracene was transformed via a typical pathway of ligninolytic fungi to benz[a]anthracene-7,12-dione (BaAQ). The product was further transformed by at least two ways, whereas one is complied with the anthracene metabolic pathway of I. lacteus. Benz[a]anthracene-7,12-dione was degraded to 1,2-naphthalenedicarboxylic acid and phthalic acid that was followed with production of 2-hydroxymethyl benzoic acid or monomethyl and dimethylesters of phthalic acid. Another degradation product of BaAQ was identified as 1-tetralone. Its transformation via 1,4-naphthalenedione, 1,4-naphthalenediol and 1,2,3,4-tetrahydro-1-hydroxynaphthalene resulted again in phthalic acid. None of the intermediates were identified as dead-end metabolites. Metabolites produced by ring cleavage of benz[a]anthracene using the ligninolytic fungus are firstly presented in this work.     

Further studies on the uptake of persistent organic pollutants (POPs) by polyurethane foam disk passive air samplers

Passive air samplers (PAS) can be used to monitor semi-volatile organic compounds in the atmosphere. Polyurethane foam (PUF) disks are a popular sampling medium because they have a high retention capacity for such compounds. This paper reports a highly time-resolved uptake study, to derive uptake rate data under field conditions, and investigate the effects of using different foam densities on the uptake rate. PUF disks were deployed alongside an active sampler, for periods of up to 12 weeks. The uptake rates were measured for a range of gas- and particle-bound persistent organic pollutants (polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs)), of different properties, to explore whether gas–particle partitioning affected uptake rate. Uptake rates for two different densities of foam (0.021 and 0.035 g cm^?3) were not statistically significantly different from each other. Uptake rates of light PCBs averaged ～6.5 m³ day^?1, somewhat higher than in previous studies; higher wind speeds and lower temperatures in this study are the likely reason for this difference. The study showed: i) the uptake rate of the compound with lowest K_OA considered in this study (PCB-28/31) declined in the later weeks, indicating an approach to equilibrium; ii) uptake rates of lighter BDEs and heavier PCBs (compounds of intermediate K_OA in this study) remain similar throughout the study period, indicating that they are not approaching equilibrium during the 12-week-study; iii) uptake rates were typically: ～8 m³ day^?1 for PCB-52; ～9.5 m³ day^?1 for PCB-95; ～11 m³ day^?1 for BDE-28 and ～2 m³ day^?1 BDE-99. The latter compound has an important particle-bound component and this lowers the sampling rate compared to predicted uptake rates for compounds which are in the gas phase only. It is shown that knowledge of gas–particle partitioning is needed to correct for this effect, and to improve predicted uptake rates.