危险品仓库静电隐患的测量、评估与防护危险品工作区域中人体静电隐患的防护

阐述了危险品工作区域中人体静电防护的必要性,总结了人体静电的起因和危害形式,给出了危险品工作区域中人体静电隐患防护的几个方法.     

添加炭基材料对蔬菜废物好氧堆肥进程和腐熟度的影响

以蔬菜废弃物辣椒秸秆和树叶为堆肥原料(CK),采用密闭式好氧堆肥工艺,研究了添加5%木本泥炭(T1)、5%活性炭(T2)和10%木本泥炭(T3)等炭基材料对堆肥pH、EC、CO2累积量、物料损失率、T值、C/N和发芽率指数的影响。结果显示,T2处理的pH在60 d后维持在8~9之间;EC值随着堆肥进行呈现先下降后升高再下降的趋势,最终CK、T1、T2和T3处理的EC值(mS/cm)分别降低了1.02、0.76、0.33和0.48;T2和T3处理的CO2累积量一直高于其他处理;所有处理的物料损失率均在20%以上;4个处理堆肥产品的T值分别为0.56、0.65、0.68和0.69;堆肥产品的发芽率指数分别为63.2%、69.3%、93.5%和86.1%。T值和发芽率指数显示T2和T3处理达到了腐熟阶段。结果表明,在蔬菜堆肥处理中添加炭基材料可改善堆肥产品的理化性质,加速堆肥物料的分解,有效地缩短堆肥周期和提高堆肥产品的腐熟度。     

沼气增温与控制系统的设计与仿真

冬季北方寒冷地区温度偏低,难以满足大中型沼气厌氧发酵系统对于温度的要求。为了解决该问题,针对天津地区某奶牛场沼气工程,设计了一套回收发电机余热并辅助电加热为发酵罐体供热的沼气增温控制系统,且实验确定最佳控制温度为35℃。在该系统中,罐体内部均匀布置竖直型循环加热管路,从而使料液温度分布更加均匀,热响应更加迅速,6 d左右即可将发酵罐内发酵料液提升到所需最佳温度;另外,采用罐内部温度及循环水流量的反馈调节,使料液的温度波动维持在±1℃范围内,解决了在冬季由于温度过低而导致沼气产气率偏低、甚至停滞的问题;同时,采用MATLAB软件对基于F-PID及传统PID的温度控制系统进行了仿真。对比结果表明,F-PID控制器较传统PID控制器超调量减小3℃,响应时间缩短60%,表明F-PID系统具有更高的效率、稳定性及实用价值。     

Molecular composition of recycled organic wastes,as determined by solid-state 13C NMR and elemental analyses

Using solid state ¹³C NMR data and elemental composition in a molecular mixing model, we estimated the molecular components of the organic matter in 16 recycled organic (RO) wastes representative of the major materials generated in the Sydney basin area. Close correspondence was found between the measured NMR signal intensities and those predicted by the model for all RO wastes except for poultry manure char. Molecular nature of the organic matter differed widely between the RO wastes. As a proportion of organic C, carbohydrate C ranged from 0.07 to 0.63, protein C from <0.01 to 0.66, lignin C from <0.01 to 0.31, aliphatic C from 0.09 to 0.73, carbonyl C from 0.02 to 0.23, and char C from 0 to 0.45. This method is considered preferable to techniques involving imprecise extraction methods for RO wastes. Molecular composition data has great potential as a predictor of RO waste soil carbon and nutrient outcomes.     

An investigation on pollutant emissions from co-firing of RDF and coal

Pollutant emissions from co-firing of refuse derived fuel (RDF) and coal were investigated in a vortexing fluidized bed combustor (VFBC). RDF-5 was made of common municipal solid waste (MSW). CaCO₃ was injected in the combustor to absorb HCl at 850 °C. The results show that NO_x and HCl emissions increase with RDF-5 co-firing ratio. The NO_x concentration in flue gas at the bottom of the combustor is higher than that at the top. However, the trend of HCl released is reverse compared with NO_x emissions. It was found that the HCl concentration decreases with increasing the molar ratio of Ca/Cl. However, the effect of CaCO₃ addition on HCl retention is not significant when the molar ratio of Ca/Cl is higher than 5. The chlorine content in fly ash increases obviously with the molar ratio of Ca/Cl. PCDD/Fs emissions decrease slightly with an addition of CaCO₃. In this study incomplete combustion is regarded as the main cause for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) formation.     

Energy recovery from waste incineration: Assessing the importance of district heating networks

Municipal solid waste incineration contributes with 20% of the heat supplied to the more than 400 district heating networks in Denmark. In evaluation of the environmental consequences of this heat production, the typical approach has been to assume that other (fossil) fuels could be saved on a 1:1 basis (e.g. 1 GJ of waste heat delivered substitutes for 1 GJ of coal-based heat). This paper investigates consequences of waste-based heat substitution in two specific Danish district heating networks and the energy-associated interactions between the plants connected to these networks. Despite almost equal electricity and heat efficiencies at the waste incinerators connected to the two district heating networks, the energy and CO₂ accounts showed significantly different results: waste incineration in one network caused a CO₂ saving of 48 kg CO₂/GJ energy input while in the other network a load of 43 kg CO₂/GJ. This was caused mainly by differences in operation mode and fuel types of the other heat producing plants attached to the networks. The paper clearly indicates that simple evaluations of waste-to-energy efficiencies at the incinerator are insufficient for assessing the consequences of heat substitution in district heating network systems. The paper also shows that using national averages for heat substitution will not provide a correct answer: local conditions need to be addressed thoroughly otherwise we may fail to assess correctly the heat recovery from waste incineration.     

A lysimeter experimental study and numerical characterisation of the leaching of incinerator bottom ash waste

Incinerator bottom ash (IBA) is a residual produced from incinerating municipal solid waste. In the past, IBA presented a big waste disposal problem; however, various recycling approaches have been adopted in recent years to mitigate this problem, as well as to provide a useful alternative to using primary aggregate resources. The use of IBA as an alternative to conventional aggregates in different civil engineering construction applications helps to conserve premium grade aggregate supplies; however, when IBA is in contact with water in the field, as a consequence of precipitation events or changes in water table, elements, such as salts and heavy metals, may be released to the soil and ground water. In this work, IBA waste was mixed with limestone aggregate to produce a blend with acceptable mechanical properties and minimum environmental risks for use as road foundation. The study focused on evaluating potential environmental impacts of some constituents, including sulphate, chloride, sodium, copper, zinc and lead in IBA blends using a lysimeter as a large scale leaching tool. Moreover, a specific scenario simulating field conditions was adopted in the lysimeter to assess the potential impact of changing conditions, such as IBA content in the blend, liquid to solid ratio (L/S) and pH value, on long-term release of heavy metals and salts. Then, numerical modelling was used to predict the release of the aforementioned constituents from IBA based on initial measurement of intrinsic material properties and the kinetic desorption process concept. Experimental results showed that zinc and lead were released in very low concentrations but sodium and sulphate were in high concentrations. The control limestone only blend also demonstrated low release concentrations of constituents in comparison to IBA blends, where constituent concentrations increased with increase in IBA content. Experimental results were compared with numerical results obtained using a non-equilibrium desorption model. Good agreement was found between the two sets of data.     

Co-digestion of sewage sludge with glycerol to boost biogas production

The feasibility of adding crude glycerol from the biodiesel industry to the anaerobic digesters treating sewage sludge in wastewater treatment plants was studied in both batch and continuous experiments at 35 °C. Glycerol addition can boost biogas yields, if it does not exceed a limiting 1% (v/v) concentration in the feed. Any further increase of glycerol causes a high imbalance in the anaerobic digestion process. The reactor treating the sewage sludge produced 1106 ± 36 ml CH₄/d before the addition of glycerol and 2353 ± 94 ml CH₄/d after the addition of glycerol (1% v/v in the feed). The extra glycerol-COD added to the feed did not have a negative effect on reactor performance, but seemed to increase the active biomass (volatile solids) concentration in the system. Batch kinetic experiments showed that the maximum specific utilization rate (μ_max) and the saturation constant (K_S) of glycerol were 0.149 ± 0.015 h^?1 and 0.276 ± 0.095 g/l, respectively. Comparing the estimated values with the kinetics constants for propionate reported in the literature, it can be concluded that glycerol uptake is not the rate-limiting step during the process.     

Cell phone recycling experiences in the United States and potential recycling options in Brazil

This paper presents an overview of cell phone recycling programs currently available in the United States. At the same time, it also provides analyses of the current recycling situation and possible recycling alternatives for Brazil. Although there are several recycling options in the United States, collection rates are still only 10% of all potential devices because customers are not aware of these possibilities. The whole system is financially based on reselling refurbished cell phones and recycled materials to developing countries which represent an effective and strong market. Several recyclers offer funds to collection partners who are either charities or who work with charities while obtaining the materials that they need in order to run their operations. A mobile phone recycling system for Brazil considering the United States experience and the Extended Producer Responsibility (EPR) principle is suggested. A deposit/refund/advance-recycling fee is proposed which might be implemented as a voluntary industrial initiative managed by PRO Brazil, a producer responsibility organization. One widespread public–private agreement will integrate all mobile phone stakeholders, and environmental education actions and promotional events will promote citizen’s participation.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.