酱糟与醋糟混合发酵产沼气研究

酱糟、醋糟是我国食品酿造行业产生的废弃物,通过厌氧发酵不仅可以解决废糟处理问题又可获取能源.因此本研究在中温(35±1)℃的条件下,根据C/N比的不同,进行了酱糟/醋糟干物质(TS)比分别为1∶0(N1)、1∶1.5(N2)、1∶3(N3)、1∶7(N4)、1∶18(N5)和0∶1(N6)的混合发酵实验.结果表明,单一酱渣的延滞期为17.46 d,混合发酵明显缩短了延滞期,为3.00-3.83 d;混合发酵组(N2～N5)累计产甲烷量的实验结果比计算结果分别提高了1％、16％、14％和10％,其中,N3组C/N比为25.7∶1,提高最为明显;各组发酵产生的沼气的甲烷体积分数在65％～ 70％之间;Gompertz模型拟合可以用于酱糟和醋糟混合发酵产甲烷的过程;酱、醋糟发酵的产酸类型以乙酸型发酵为主.     

高温载硫活性炭的制备及脱汞能力研究

研究了载硫温度、硫炭比(简称S/C),吸附温度等因素对载硫活性炭的硫含量、脱汞能力以及硫损失的影响,探讨载硫活性炭制备的工艺条件优化。结果表明,不同载硫温度下制备的载硫活性炭的气态Hg0吸附能力远强于原料活性炭;载硫温度不同时,负载到活性炭孔隙或表面上的硫的形态不同,导致了脱汞能力的差异,较合适的载硫温度为350℃;S/C为5%(质量分数,下同)时,随着吸附温度的升高,载硫活性炭的气态Hg0吸附量降低;在一定的载硫温度下,原料中S/C越高时,制备的载硫活性炭的硫含量越高、气态Hg0吸附能力越强,但其硫损失率也越高,从实际的使用效果来看,较合适的S/C为10%。     

Levels and speciation of arsenic in the atmosphere in Beijing, China

Arsenic levels and speciation in the total suspended particles (TSPs) were quantitatively determined by high performance liquid chromatography on-line coupled with hydride generation atomic fluorescence spectrometry in Beijing, China from February 2009 to March 2011. The high TSP levels fluctuated between 0.07 and 0.79 mg m⁻³, with a mean level of 0.32 ± 0.17 mg m⁻³. The total arsenic concentrations ranged from 0.03 to 0.31 μg m⁻³ (mean: 0.13 ± 0.06 μg m⁻³) in Beijing‘s air. The concentrations of As(III) and As(V) ranged from 0.73 to 20 ng m⁻³ (mean: 4.7 ± 3.6 ng m⁻³) and from 14 to 2.5 × 10² ng m⁻³ (mean: 67 ± 35 ng m⁻³), respectively. As levels and speciation demonstrated relative higher levels in spring and autumn and lower values in summer and winter. As(V) accounted for 81-99% of the extractable species in the TSP samples which showed that As(V) was the major fraction of the extractable As. Organoarsenic species, monomethylarsonate (MMA) and dimethylarsinate (DMA) were not found in all samples. Higher values of enrichment factors demonstrated that arsenic in TSP mainly come from anthropogenic sources. High As and its species levels in air and respiratory exposure (0.30-0.84 μg d⁻¹) attributed to higher excess cancer risk ((4.2 ± 2.0) × 10⁻⁴) for people in Beijing.     

Mn-Ce/TiO2低温SCR催化剂成型过程添加剂的影响

催化剂成型过程中添加剂的种类和添加量对成型后催化剂的机械强度、成型效果和催化性能有很大影响.本文研究了Mn-Ce/TiO₂催化剂制备过程中添加剂对催化剂的低温脱硝性能和机械性能的影响.结果表明,添加10%的拟薄水铝石作为黏结剂,可使催化剂具有较强的机械强度;添加2.5%的活性炭作为造孔剂,可以有效改善催化剂的孔结构.催化剂成型后脱硝性能下降,反应温度为90℃和120℃时,催化剂的NO_x转化率分别下降了15%和30%左右,当温度到达150℃及以上时,催化剂成型前后的脱硝性能基本一致.最后,通过BET、FT-IR、NH₃-TPD和H₂-TPR表征分析原因：成型后催化剂比表面积和孔容下降,催化剂的表面酸性位点和氧化还原能力下降都会影响催化剂的脱硝性能,所以催化剂成型后低温活性变差.     

生理节律对北京市出租车司机驾驶疲劳的影响

为探索生理节律对出租车司机驾驶疲劳的影响,选取具有代表性的15名北京市出租车司机,使用闪光融合频率计、动作稳定器、视觉反应时测试仪3种实验仪器,分实验组和空白组对出租车司机驾驶状态分时段进行多次测试,在数据统计分析基础上对出租车司机疲劳规律进行研究.结果 表明:出租车司机驾驶疲劳主要表现为困倦、身体不适以及倦怠3个方面.8:00司机疲劳程度最低,13:00疲劳特征关键点;7:00 ～13:00疲劳主要因素是生理节律,其显著特征是困倦,而工作方式对疲劳的影响相对较小;13:00 ～ 20:00疲劳的主要因素是工作方式和生理节律,其显著特征是困倦、身体不适和倦怠.     

Purification and characterization of Al13 species in coagulant polyaluminum chloride

Nano-Al₁₃ was separated and purified by four methods to investigate its characteristic, and was analyzed by Al-Ferron timed complexation spectrophotometer,²⁷ Al-NMR (nuclear magnetic resonance), and transmission electron microscopy (TEM). Coagulation efficiency of nano-Al₁₃, polyaluminum chloride (PAC), and AlCl₃ in synthetic water were also investigated by jar test. The dynamic process and aggregation state of kaolin suspensions coagulating with nano-Al₁₃, PAC, and AlCl₃ were also investigated. The experimental results indicated that the efficiency of gel column chromatography method was the highest for separating PAC solution with low Al concentration. Ethanol and acetone method was simple and could separated PAC solution with different Al concentrations, while silicon alkylation white block column chromatography method could separate PAC solution only with low Al concentration. The SO₄²−/Ba²⁺ displacement method could separate PAC solution with high Al concentration, but extra inorganic cation and anion could be introduced into the solution during the separation. The coagulation efficiency and dynamic experimental results showed that nano- Al₁₃ with a high positive-charged species was the main species of electric neutralization in coagulation process, and it could reduce the turbidity and increase the effective particles collision rate efficiently in coagulation process. Its coagulation speed and the particle size of coagulant formed were of greatest value in this study.     

工业污泥发生量估算方法的探讨

根据物料平衡原理,推导出用于估算悬浮物污泥、有机污泥和重金属污泥等发生量的简便公式,并用某市工业污泥发生量的调查资料加以验证,结聚表明,估算值的相对误差仅为6.3％。     

纳米Al13的分离方法及混凝效果动态过程的研究

以相同Al13含量、不同浓度的PAC为原料,利用乙醇-丙酮混合溶剂法、SO4^2-／Ba^2 沉淀置换法以及柱层析法分离提纯纳米Al13形态,同时利用Al-Ferron逐时络合比色法、^27Al-NMR等多种现代分析手段进行分析鉴定,比较其分离效果,并采用烧杯实验法和透光率脉动检测技术对Al13形态以及PAC、AlCl3的絮凝效果及絮凝过程中絮集物形成和增长的变化差异作了对比性研究．实验结果表明,乙醇．丙酮混合溶剂法对Al13分离纯化效果最好,分离所得Al13平均粒径大,聚合程度高．柱层析法受柱体积的影响只对低浓度的PAC有较好的分离效果;SO4^2-／Ba^2 沉淀置换法虽具有较好的分离效果,但分离过程有其他杂质离子的加入,影响到产品品质．混凝效果和动态实验结果表明,Al13形态是在絮凝过程中起电中和作用的主要形态,具有较强的除浊及脱色能力,在混凝过程中当絮体受到剪切力的破坏时Al13形态比PAC和AlCl3具有更强重新絮凝的能力．     

Separating method and dynamic processes of Nano-Al13

In order to investigate the characteristics of pure Nano-Al₁₃, Nano-Al₁₃ was separated and purified from a series of poly-aluminum chloride (PAC) solutions which had the same Al₁₃ percentage but different total Al concentrations, by using column chromatography, ethanol-acetone resolving and SO²⁻ ₄/Ba²⁺ displacement. The Al₁₃ species yield was characterized by Al-ferron timed complexation spectrophotometry and ²⁷Al-NMR (nuclear magnetic resonance). The coagulation efficiency of Nano-Al₁₃, PAC and AlCl₃ in synthetic water was also investigated by Jar tests. The dynamic process and aggregation state of kaolin suspensions coagulating with Nano-Al₁₃, PAC and AlCl₃ were similarly investigated using a photometric dispersion analyzer 2000 (PDA2000). The experimental results indicated that the ethanol-acetone resolving method was simple and could separate the PAC solution at different concentrations, while column chromatography could separate PAC solutions at low concentrations. The SO₄ ²⁻/Ba²⁺ displacement method could separate PAC solutions at high concentrations. However, extra inorganic cation and anion could be added in the solution during separation. The coagulation efficiency and dynamic experimental results showed that Nano-Al₁₃ with high positive-charged species was effective in removing turbidity and color. The dynamic process results showed that Nano-Al₁₃ also had the best recovery capability after shearing compared with PAC and AlCl₃ because the Nano-Al₁₃ conformation is more effective in charge neutralization. Translated from Acta Scientiae Circumstantiae, 2005, 25(6): 767–772 [译自: 环境科学学报]     

浅论工业固体废物的资源化和减量化

从工业固体废物所具有的资源性特征出发,简要论述了工业固体废物资源化和减量化的重要意义。通过对资源化前景的分析,提出了发展社会化,专业化资源再利用和加强立法保障的对策建议。通过对国内外废物减量化的一些实例分析,论述了废物减量化的根本途径和今后的发展方向。