Forest carbon management in the United States: 1600-2100

This paper reviews the effects of past forest management on carbon stocks in the United States, and the challenges for managing forest carbon resources in the 21st century. Forests in the United States were in approximate carbon balance with the atmosphere from 1600-1800. Utilization and land clearing caused a large pulse of forest carbon emissions during the 19th century, followed by regrowth and net forest carbon sequestration in the 20th century. Recent data and knowledge of the general behavior of forests after disturbance suggest that the rate of forest carbon sequestration is declining. A goal of an additional 100 to 200 Tg C/yr of forest carbon sequestration is achievable, but would require investment in inventory and monitoring, development of technology and practices, and assistance for land managers.     

MULTI INCREMENT® TCE vadose‐zone investigation

MULTI INCREMENT® and discrete sampling strategies were used to estimate the average concentration and the three‐dimensional distribution of TCE in a 3,300‐m³ zone composed of two decision units (e.g., area of concern, population, exposure unit). Authors of this article and a private contractor (Stanley Consultants Inc.), respectively, implemented these two sampling strategies independently. Compared to discrete sampling, the MULTI INCREMENT sampling strategy identified more locations where percent‐level concentrations of TCE have migrated, is more economical, and provided greater data quality. © 2008 Wiley Periodicals, Inc.     

Monitoring of carbon monoxide in residences with bulk wood pellet storage in the Northeast United States

The interest in biomass fuel is continuing to expand globally and in the northeastern United States as wood pellets are becoming a primary source of fuel for residential and small commercial systems. Wood pellets for boilers are often stored in basement storage rooms or large bag-type containers. Due to the enclosed nature of these storage areas, the atmosphere may exhibit increased levels of carbon monoxide. Serious accidents in Europe have been reported over the last decade in which high concentrations of carbon monoxide (CO) have been found in or near bulk pellet storage containers. The aim of this study was to characterize the CO concentrations in areas with indoor storage of bulk wood pellets. Data was obtained over approximately 7 months (December 2013 to June 2014) at 25 sites in New Hampshire and Massachusetts: 16 homes using wood pellet boilers with indoor pellet storage containers greater than or equal to 3 ton capacity; 4 homes with wood pellet heating systems with outdoor pellet storage; 4 homes using other heating fuels; and a university laboratory site. CO monitors were set up in homes to collect concentrations of CO in the immediate vicinity of wood pellet storage containers, and data were then compared to those of homes using fossil fuel systems. The homes monitored in this study provided a diverse set of housing stock spanning two and a half centuries of construction, with homes built from 1774 to 2013, representing a range of air exchange rates. The CO concentration data from each home was averaged hourly and then compared to a threshold of 9 ppm. While concentrations of CO were generally low for the homes studied, the need to properly design storage locations for pellets is and will remain a necessary component of wood pellet heating systems to minimize the risk of CO exposure.

Implications: This paper is an assessment of carbon monoxide (CO) exposure from bulk wood pellet storage in homes in New Hampshire and Massachusetts. Understanding the CO concentrations in homes allows for better designs for storage bins and ventilation for storage areas. Hence, uniform policies for stored wood pellets in homes, schools, and businesses can be framed to ensure occupant safety. Currently in New York State rebates for the installation of wood pellet boilers are only provided if the bulk pellet storage is outside of the home, yet states such as New Hampshire, Vermont, and Maine currently do not have these restrictions.     

Variance Design and Air Pollution Control

Confronted with shortages of low sulfur content residual fuel oil and, consequently, faced with the threat of social and economic upheaval, several air pollution control authorities in the Northeastern states were forced to relax hard-won air quality standards during the winter of 1972. The authorities did so by granting variances to their sulfur content standards for residual fuel oil. This paper examines the institutional characteristics of these variance policies from an economic incentive standpoint. After setting up desirable structural criteria for institutional design of such crisis policies, the authors examine the experience of the winter of 1972 and arrive at policy guidelines which recommend themselves for consideration in future periods of fuel oil shortages.     

Salinity modulates biochemical and histopathological changes caused by silver nanoparticles in juvenile Persian sturgeon (Acipenser persicus)

Environmental Science and Pollution Research - The objective of this study was to evaluate the effect of salinity on the acute and sub-chronic toxicity of silver nanoparticles (AgNPs) in Persian...     

Development of a microscale emission factor model for particulate matter for predicting real-time motor vehicle emissions

The U.S. Environmental Protection Agency's National Exposure Research Laboratory is pursuing a project to improve the methodology for modeling human exposure to motor vehicle emissions. The overall project goal is to develop improved methods for modeling the source through the air pathway to human exposure in significant exposure microenvironments. Current particulate matter (PM) emission models, particle emission factor model (used in the United States, except California) and motor vehicle emission factor model (used in California only), are suitable only for county-scale modeling and emission inventories. There is a need to develop a site-specific real-time emission factor model for PM emissions to support human exposure studies near roadways. A microscale emission factor model for predicting site-specific real-time motor vehicle PM (MicroFacPM) emissions for total suspended PM, PM less than 10 microm aerodynamic diameter, and PM less than 2.5 microm aerodynamic diameter has been developed. The algorithm used to calculate emission factors in MicroFacPM is disaggregated, and emission factors are calculated from a real-time fleet, rather than from a fleet-wide average estimated by a vehicle-miles-traveled weighting of the emission factors for different vehicle classes. MicroFacPM requires input information necessary to characterize the site-specific real-time fleet being modeled. Other variables required include average vehicle speed, time and day of the year, ambient temperature, and relative humidity.     

Consequences of raising the speed limit

Two methods were used to assess the potential impact of increased speed limits on highway fatalities. These were: (a) a method used by National Safety Council (NSC) in estimating the causes of decreased motor vehicles in the 1970s and (b) a method used by the National Research Council, Transportation Research Board (TRB) in reporting on 10 years of experience with the 55 mph speed limit. Applying the NSC method to 1984 fatality data resulted in estimated increases of 200 to 700 deaths per year on rural interstates depending on how much the speed limit was raised. Using the TRB method resulted in estimated increases of 300 to 450 deaths per year if each state returned to pre-1974 speed limits.