常熟河网区水污染物总量控制研究

基于常熟河网原型调水实验和水功能区划，建立了感潮地区河网水量水质模型，对常熟河道水质降解系数及水环境容量进行了计算，并按照点源和面源对区域内污染源进行统计，在此基础上进行了常熟河网水污染物总量控制值和现状削减量的计算，为该地区的水污染防控提供了科学依据。     

强化一级处理与SBR工艺处理油脂精炼加工废水

介绍了规模为200 m^3/d的油脂精炼加工废水处理工程的设计与运行.先经强化一级处理工艺预处理,再经SBR工艺处理,出水的有关指标能达到设计的排放标准,工艺运行稳定.     

生物炭/铁酸镧磁性复合材料的制备及对亚甲基蓝的吸附性能

为获得吸附性能良好、便于回收利用的新型吸附剂以处理染料废水,采用超声辅助溶胶-凝胶法将铁酸镧(LaFeO_3)经过一步热解负载于生物炭制得生物炭/LaFeO_3磁性复合材料(BC/FL)。其表面形态、结构和组成分析表明:BC/FL的比表面积、总孔容及平均孔径分别为34.67m2/g、0.041cm3/g和7.82nm,磁饱和强度达到40.283A/m,表面含有C=O、C=C=N、C≡C等官能团。批量吸附实验表明,25℃下,当亚甲基蓝(MB)的初始质量浓度为30mg/L时,BC/FL的最佳投加量为1.5g/L,吸附反应在120min达到平衡,去除率可达92.3%,且吸附效果基本不受pH影响。BC/FL对MB的吸附符合准二级动力学模型,Langmuir模型可描述其等温吸附过程。化学吸附占主导地位,主要机理为静电吸附、氢键和π-π共轭作用。吸附反应为单分子层吸附且为自发的吸热过程。     

SBR法降解有机物规律的研究

本研究是以处理啤酒废水的试验为基础展开的。试验结果进一步验证了SBR法具有简易,快速、低耗等优点。除此之外,还得出以下结论:增加间歇反应时起始污泥浓度可以提高处理效率或减少反应时间;非限制曝气方式耐冲击负荷,需氧均匀,能缩短反应周期;间歇反应中微生物细胞的合成代谢占主导地位,对氮与磷的需要量大于传统的理论值。本文还指出SBR法是很适合我国国情的一种废水处理工艺,应当加强对它的研究和推广应用。     

Photocatalytic reactions of phenanthrene at TiO2/water interfaces

The photocatalytic oxidation of phenanthrene was investigated in aqueous TiO2 suspensions under UV light irradiation. Chemical oxygen demand (COD) measurements, UV-Vis spectrophotometer, IR spectrometer and gas chromatography-mass spectrometry (GC-MS) analytical techniques were used to monitor the reaction process. Some factors affecting the photodegradation rate were studied and some aromatic intermediates were detected during the reaction process. Fast and complete mineralization of phenanthrene was achieved in this reaction system.     

A/O脱氮工艺的控制策略和应用性研究

根据A/O脱氮工艺的运行状况和影响因素 ,提出了应用在线传感器连续测定曝气池中DO浓度、氨氮浓度和硝酸氮浓度 ,并据此调节供氧强度、内循环回流量、有机碳源的投加以及硝化区和反硝化区的大小 ,这是保证A/O脱氮工艺良好处理效果的重要控制策略和思想。同时对近年来国外A/O脱氮工艺自动控制的应用及研究进行了简单的回顾。     

柱生物曝气法吸附处理含铬废水

利用复合生物吸附剂FY01与活性污泥作为吸附材料，探讨了柱式生物曝气法对高浓度含铬电镀废水的生物吸附效果。研究结果表明，FY01性能稳定，耐进水pH冲击能力较强。当进水pH=2—5、流速为500mL／h时，10gFY01和5g活性污泥联合处理60．4mg／L含铬电镀废水2h后，铬的去除率达78％以上；在4℃冰箱和23—28℃实验室保存50d的FY01对铬的去除分别在78％～83％和77％-84％之间。柱式生物曝气吸附法对含铬废水的处理效果理想，运行稳定。串联处理2000mL总Cr、Cu^2＋和COD浓度分别为60．4、4．51和48．2mg／L的电镀废水2h后，去除率分别高达92．1％、99．2％和71．4％。     

Co-surfactant of ethoxylated sorbitan ester and sorbitan monooleate for enhanced flushing of tetrachloroethylene

This work evaluated the flushing efficiency of tetrachloroethylene (PCE) using the co-surfactant of non-ionic ethoxylated sorbitan ester (Tween) and oilphilic sorbitan monooleate (Span 80), which formed more hydrophobic micelles than Tween alone. The flushing efficiency was evaluated with laboratory columns filled with silica and aquifer sand. Results from column flushing were also compared to those of batch solubility experiments to study the removal mechanism by the co-surfactant solution. Compared to Tween 80 alone, the molar solubilization ratio and the affinity between the micelles and PCE increased 84% and 90%, respectively, by the co-surfactant solution of Tween 80 and Span 80 mixed at a 4:1 ratio. Flushing with 1% Tween 80 solution yielded a steady PCE recovery of 7% for both silica and aquifer sand in each pore volume (PV). Flushing with co-surfactant of 1% Tween 80 + Span 80 (4:1) further increased PCE recovery to 10% for silica sand and 13% for aquifer sand per PV. A comparison of results from column flushing and batch solubility tests indicated that the primary flushing mechanism of PCE using the co-surfactant solution of Tween 80 + Span 80 (4:1) was micellar solubilization.     

Controlled exposures of volunteers to respirable carbon and sulfuric acid aerosols.

Respirable carbon or fly ash particles are suspected to increase the respiratory toxicity of coexisting acidic air pollutants, by concentrating acid on their surfaces and so delivering it efficiently to the lower respiratory tract. To investigate this issue, we exposed 15 healthy and 15 asthmatic volunteers in a controlled-environment chamber (21 degrees C, 50 percent relative humidity) to four test atmospheres: (i) clean air; (ii) 0.5-microns H2SO4 aerosol at approximately 100 micrograms/m3, generated from water solution; (iii) 0.5-microns carbon aerosol at approximately 250 micrograms/m3, generated from highly pure carbon black with specific surface area comparable to ambient pollution particles; and (iv) carbon as in (iii) plus approximately 100 micrograms/m3 of ultrafine H2SO4 aerosol generated from fuming sulfuric acid. Electron microscopy showed that nearly all acid in (iv) became attached to carbon particle surfaces, and that most particles remained in the sub-micron size range. Exposures were performed double-blind, 1 week apart. They lasted 1 hr each, with alternate 10-min periods of heavy exercise (ventilation approximately 50 L/min) and rest. Subjects gargled citrus juice before exposure to suppress airway ammonia. Lung function and symptoms were measured pre-exposure, after initial exercise, and at end-exposure. Bronchial reactivity to methacholine was measured after exposure. Statistical analyses tested for effects of H2SO4 or carbon, separate or interactive, on health measures. Group data showed no more than small equivocal effects of any exposure on any health measure.(ABSTRACT TRUNCATED AT 250 WORDS)     

中国钢铁行业大气环境影响

本研究基于2015年在线监测等数据,分析中国钢铁行业主要工序(烧结和球团)排口烟气浓度情况,自下而上建立了2015年中国高时空分辨率钢铁行业大气污染物排放清单(HSEC, 2015),使用CAMx模型,定量模拟钢铁行业排放对区域大气污染物浓度贡献.结果表明, 2015年中国钢铁行业共排放SO_2、NO_x、PM_(10)、PM_(2.5)、PCDD/Fs、VOCs、CO、BC、OC、EC和F分别为37.48万t、 72.05万t、 33.48万t、 15.03万t、 1.91 kg、 84.29万t、 3 478.85万t、 0.64万t、 0.83万t、 0.08万t和0.77万t.从区域角度:上海和天津钢铁行业单位面积污染排放强度最大,对区域大气污染贡献比例较高.从工序角度:2015年烧结和球团烟气排口月平均浓度降低.从污染物角度:2015年钢铁行业排放NO_x对区域污染物浓度贡献最大,NO_x具有较大的减排潜力.