The Effect of Fuel Composition on Atmospheric Aerosol Due to Auto Exhaust

Aerosols attributable to automobile exhaust can be classified as two types—primary aerosol (initially present in the exhaust) and secondary aerosol (generated photochemically from hydrocarbons and nitrogen oxides in the exhaust). In this study, investigation was made of possible effects of motor-fuel composition on the formation of these aerosols. Secondary aerosol, of principal interest in this work, was produced by irradiating auto exhaust in Battelle-Columbus’ 610 ft³ environmental chamber. A limited number of determinations of primary aerosol in diluted auto exhaust was made at the exit of a 36 ft dilution runnel. Determination of both primary and secondary aerosol was based on light-scattering measurements.

Exhaust was generated with seven full-boiling motor gasolines, both leaded and nonleaded, in a 1967 Chevrolet which was not equipped with exhaust-emission control devices. Changes in fuel composition produced a maximum factor of three difference in light scattering due to primary aerosol. Aerosol yields, for consecutive driving cycles on the same fuel, vary considerably; as a result, ranking the fuels on the basis of average primary aerosol yield was not very meaningful. In addition to fuel composition, the more important independent variables are initial SO₂ concentration, relative humidity and initial hydrocarbon concentration. Statistical analysis of the data indicates that the seven test fuels can be divided into two arbitrary groups with regard to secondary aerosol-forming potential. The fuels in the lower light-scattering group had aromatic contents of 15 and 21%, while those in the higher light-scattering group had aromatic contents of 25, 48, and 55%. Although the fuels can be grouped on the basis of a compositional factor, the grouping of fuels with aromatic content ranging from 25 to 55% indicates that this compositional factor cannot be equated simply with aromatic content. In an associated study of the aerosol-forming potential of individual hydrocarbons prominent in auto exhaust, it was observed that aromatics produce substantially more photochemical aerosol than olefins and paraffins. However, experiments with binar/hydrocarbon mixtures containing aromatjcs, as well as in these exhaust experiments, a strong dependence of aerosol yield on the aromatic components is is not observed. Thus, the data indicate that the dependence of secondary aerosol formation on fuel factors is a complex one and cannot be predicted solely on the basis of a sirigle hydrocarbon component reactivity scale.

The two types of automobile aerosol did not have the same dependence on fuel, composition. The variation in total light scattering attributable to primary plus secondary aerosol was less than that due to either component alone. It therefore was concluded that the light scattering due to automobile exhaust emissions in these experiments was not significantly affected by changing fuel composition.     

Indoor Nitrogen Dioxide Exposure and Children’s Pulmonary Function

Elevated concentrations of nitrogen dioxide (NO₂) are produced in the home by the use of unvented gas appliances. In studies on potential health effects of Indoor exposure to NO₂, exposure has mostly been estimated from the presence or absence of sources like gas cookers in the home. This leads to misclassification of exposure, as NO₂ concentrations in the home depend also on source use, ventilation habits, time budgets, etc. The availability of cheap, passive monitoring devices has made it possible to measure Indoor concentrations of NO₂ directly in health effects studies, albeit with averaging times of one to several days. So far, it has not been evaluated whether this increases the sensitivity of a study to detect health effects of NO₂. In this paper, a comparison is made between NO₂ sources and weekly average indoor NO₂ measurements, as predictors of pulmonary function in a study among children aged 6–12 years.

The relationship between exposure and lung functions was found to be generally non-significant in this study. The results further suggested that in this study, measuring Indoor NO₂ concentrations with passive monitors offered no advantage over the simple use of source presence as exposure variable.     

Evaluation of Tire-Derived Fuel for Use in Nitrogen Oxide Reduction by Reburning

ABSTRACT

Tire-derived fuel (TDF) was tested in a small-scale (44 kW or 150,000 Btu/hr) combustor to determine its feasibility as a fuel for use in reburning for control of nitrogen oxide (NO). TDF was gravity-fed into upward flowing combustion gases from a primary natural gas flame doped with ammonia to simulate a high NO combustion process. Emissions of NO, oxygen, carbon dioxide, carbon monoxide, and particulate matter were measured. The tests varied the nominal primary NO level from 600 to 1,200 ppm and the primary stoichiometry from 1.1 to 1.2, and used both natural gas and TDF as reburn fuels. The reburn injection rate was varied to achieve 8–20% of the total heat input from the reburn fuel. NO emissions reductions ranged between 20 and 63% when using TDF, depending upon the rate of TDF injection, primary NO, and primary stoichiometry. NO emission reductions when using natural gas as the reburn fuel were consistently higher than those when using TDF. While additional work remains to optimize the process and evaluate costs, TDF has been shown to have the potential to be a technically viable reburning fuel.     

Characterization of Fine Particulate Matter Produced by Combustion of Residual Fuel Oil

ABSTRACT

Combustion experiments were carried out on four different residual fuel oils in a 732-kW boiler. PM emission samples were separated aerodynamically by a cyclone into fractions that were nominally less than and greater than 2.5 |j.m in diameter. However, examination of several of the samples by computer-controlled scanning electron microscopy (CCSEM) revealed that part of the PM_2.5 fraction consists of carbonaceous cenospheres and vesicular particles that range up to 10 |j.m in diameter. X-ray absorption fine structure (XAFS) spectroscopy data were obtained at the S, V, Ni, Fe, Cu, Zn, and As K-edges and at the Pb L-edge. Deconvolution of the X-ray absorption near edge structure (XANES) region of the S spectra established that the dominant molecular forms of S present were sulfate (26-84% of total S) and thiophene (13-39% of total S). Sulfate was greater in the PM_2.5 samples than in the PM₂₅₊ samples. Inorganic sulfides and elemental sulfur were present in lower percentages. The Ni XANES spectra from all of the samples agreed fairly well with that of NiSO₄, while most of the V spectra closely resembled that of vanadyl sulfate (VO?SO₄?xH₂O). The other metals investigated (i.e., Fe, Cu, Zn, and Pb) also were present predominantly as sulfates. Arsenic was present as an arsen-ate (As⁺⁵). X-ray diffraction patterns of the PM_2.5 fraction exhibit sharp lines due to sulfate compounds (Zn, V, Ni, Ca, etc.) superimposed on broad peaks due to amorphous carbons. All of the samples contain a significant organic component, with the loss on ignition (LOI) ranging from 64 to 87% for the PM_2.5 fraction and from 88 to 97% for the PM_2.5+ fraction. Based on ¹³C nuclear magnetic resonance (NMR) analysis, the carbon is predominantly condensed in graphitic structures. Aliphatic structure was detected in only one of seven samples examined.     

An Environmental Decision-Making Tool for Evaluating Ground-Level Ozone-Related Health Effects

Abstract

A computer model called the Ozone Risk Assessment Model (ORAM) was developed to evaluate the health effects caused by ground-level ozone (O₃) exposure. ORAM was coupled with the U.S. Environmental Protection Agency’s (EPA) Third-Generation Community Multiscale Air Quality model (Models-3/CMAQ), the state-of-the-art air quality model that predicts O₃ concentration and allows the examination of various scenarios in which emission rates of O₃ precursors (basically, oxides of nitrogen [NO_x] and volatile organic compounds) are varied. The principal analyses in ORAM are exposure model performance evaluation, health-effects calculations (expected number of respiratory hospital admissions), economic valuation, and sensitivity and uncertainty analysis through a Monte Carlo simulation. As a demonstration of the system, ORAM was applied to the eastern Tennessee region, and the entire O₃ season was simulated for a base case (typical emissions) and three different emission scenarios. The results indicated that a synergism occurs when reductions in NO_x emissions from mobile and point sources were applied simultaneously. A 12.9% reduction in asthma hospital admissions is expected when both mobile and point source NO_x emissions are reduced (50 and 70%, respectively) versus a 5.8% reduction caused by mobile source and a 3.5% reduction caused by point sources when these emission sources are reduced individually.     

Some happy,others sad: exploring environmental justice in solid waste management in Kinshasa,The Democratic Republic of Congo

This paper explores the concept of environmental justice (EJ) in solid waste management (SWM) in Kinshasa, the Democratic Republic of Congo (DRC). It evaluates the extent to which EJ occurs in SWM and discusses the factors accounting for this state of affairs. The paper examines the relevant theoretical framework(s) and mechanisms that would facilitate the attainment of EJ in Kinshasa. It is argued that solid waste (SW) often ends up in the poorest and least powerful communities in the cities of the DRC. A qualitative research methodology, which includes exhaustive critical review of the literature, system analysis, reflections from best practices through case studies and discussion with stakeholders, was used for this study. Findings revealed that SWM in Kinshasa is a duty entrusted to publicly-funded municipal authorities. There are evidences of a clear divide between the rich and poor neighbourhoods in the manner SW is managed. This is an inequality that has only recently begun to be recognised as injustice practices in SWM. It is argued that a politico-cultural mechanism on remedying SWM inequities could enable changes that will address EJ in Kinshasa. Such a solution will go directly against the prevailing notion “some happy, others sad”.     

An assessment of indoor air quality in recent Mexican immigrant housing in Commerce City, Colorado

An indoor air quality assessment was conducted on 100 homes of recent Mexican immigrants in Commerce City, Colorado, an urban industrial community north of Denver. Head of households were administered a family health survey, filled out an activity diary, and participated in a home inspection. Carbon monoxide (CO) and carbon dioxide (CO₂) were measured for 24 h inside the main living area and outside of the homes. Harvard Impactors were used to collect 24-h samples of PM_2.5 at the same locations for gravimetric analysis. Dust samples were collected by vacuuming carpeting and flooring at four locations within the home and analyzed by ELISA for seven allergens. Mean indoor and outdoor PM_2.5 levels were 27.2 and 8.5 μg m⁻³, respectively. Indoor PM_2.5 and CO₂ were elevated in homes for which the number of hours with door/window open was zero compared to homes in which the number of hours was high (>15 h). Indoor PM_2.5 levels did not correlate with outdoor levels and tended to increase with number of inhabitants, and results indicate that the source of indoor particles were occupants and their activities, excluding smoking and cooking. Mean indoor CO₂ and CO levels were 1170 and 2.4 ppm, respectively. Carbon monoxide was higher than the 24-h National Ambient Air Quality Standard in 3 of the homes. The predominant allergens were cat (Fel d 1) and mouse (Mus m 1) allergens, found in 20 and 34 homes, respectively.     

The variability of free tropospheric ozone over Beltsville,Maryland (39N, 77W) in the summers 2004–2007

Ozone profiles are often used to investigate day-to-day and year-to-year variability in origins of free tropospheric ozone. With this in mind, more than 50 ozonesonde launches were conducted in Beltsville, MD, during the summers of 2004 through 2007. Budgets of free tropospheric ozone were calculated for each ozone profile in the four summers using a laminar identification (LID) method and unusual episodes were analyzed with respect to meteorological variables. The laminar method showed that stratosphere-to-troposphere transport (ST) accounted for greater than 50% of the free tropospheric ozone column on 17% of days sampled, a more pronounced influence than regional convective and lightning (RCL) sources. The ST origins were confirmed with trajectories, and tracers (water vapor and potential vorticity). The amount of free tropospheric ozone from ST and RCL sources varied from year-to-year (up to 13%) and can be explained by differences in mean meteorological patterns. On average, almost 30% of the free tropospheric column was attributed to ST influence, about twice as much as RCL, although the LID method may not capture weeks-old lightning influences as in a chemical model. The prevalence of ST ozone in summertime Beltsville soundings was similar to six sounding sites in the IONS-04 campaign [Thompson, A.M., et al., 2007b. Intercontinental Transport Experiment Ozonesonde Network Study (IONS, 2004): 1. Summertime upper tropospheric/lower stratosphere ozone over northeastern North America. J. Geophys. Res. 112, D12S12; Thompson, A.M., et al., 2007c. Intercontinental Transport Experiment Ozonesonde Network Study (IONS, 2004): 2. Tropospheric ozone budgets and variability over northeastern North America. J. Geophys. Res. 112, D12S13.] and to statistics from a 30 year climatology of European soundings [Collette, A., Ancellet, G., 2005. Impact of vertical transport processes on the tropospheric ozone layering above Europe. Part II: Climatological analysis of the past 30 years. Atmos. Environ. 39, 5423–5435]. The Beltsville record also demonstrated the value of soundings for air quality forecasting in an urban area. The 22 nighttime soundings collected over Beltsville in 2004–2007 can be divided into distinct polluted and unpolluted subsets, the former 20 ppbv higher in residual layer ozone (1 km) than the latter. These distinctions propagated to daytime differences of 10 ppbv at the surface in the Washington, DC, area, with the high-ozone residual layers leading to non-attainment of the National Ambient Air Quality Standard for ozone. More frequent ozone observations aloft appear essential for better understanding ozone variability and for enabling air quality modelers to achieve more accurate ozone forecasts.     

Does Zoning Winter Recreationists Reduce Recreation Conflict?

Environmental Management - Parks and protected area managers use zoning to decrease interpersonal conflict between recreationists. Zoning, or segregation, of recreation—often by non-motorized...     

A novel use of anaerobically digested liquid swine manure to potentially control soybean cyst nematode

Experiments were carried out in two steps to determine the effect of anaerobically digested swine manure on soybean cyst nematode (SCN) egg control. In the first step, liquid swine manure underwent anaerobic digestion to search for the best digestion time for both volatile fatty acids (VFA) and ammonium nitrogen (NH₄ ⁺) enrichment. The results showed that about 17 and 28 days of incubation were needed, respectively, to reach the maximal levels of VFA and NH₄ ⁺ in the manure. In the second step, raw, VFA-enriched, and NH₄ ⁺-enriched manure were applied separately, at four different rates (25, 50, 100, and 200 mL/pot), to soil pots inoculated with nematode eggs in a greenhouse environment. Soil samples were collected 35 and 61 days after inoculation to determine the effect of such treated manure on SCN egg productivity. The data indicated that the SCN egg counts were inversely related to the manure application rates in a linear manner with correlation coefficients of 0.998, 0.967, and 0.900 for raw, NH₄ ⁺-enriched, and VFA-enriched manure for the 35-day samples. While no such relationships were found for the 61-day samples, implying that none of the treatments were still effective 61 days after application. At the four application rates, the VFA-enriched manure performed best in reducing SCN egg counts (by 18.1, 19.5, 34.3, and 18.6%) as compared to the raw manure treatment. In contrast, the NH₄ ⁺-enriched manure achieved mostly negative reductions. To achieve the best control of SCN egg growth, the VFA-enriched manure should be used and applied to soybean fields every 35 days.