Comparison of the MOVES2010a,MOBILE6.2, and EMFAC2007 mobile source emission models with on-road traffic tunnel and remote sensing measurements

The Desert Research Institute conducted an on-road mobile source emission study at a traffic tunnel in Van Nuys, California, in August 2010 to measure fleet-averaged, fuel-based emission factors. The study also included remote sensing device (RSD) measurements by the University of Denver of 13,000 vehicles near the tunnel. The tunnel and RSD fleet-averaged emission factors were compared in blind fashion with the corresponding modeled factors calculated by ENVIRON International Corporation using U.S. Environmental Protection Agency's (EPA's) MOVES2010a (Motor Vehicle Emissions Simulator) and MOBILE6.2 mobile source emission models, and California Air Resources Board's (CARB's) EMFAC2007 (EMission FACtors) emission model. With some exceptions, the fleet-averaged tunnel, RSD, and modeled carbon monoxide (CO) and oxide of nitrogen (NO_x) emission factors were in reasonable agreement (±25%). The nonmethane hydrocarbon (NMHC) emission factors (specifically the running evaporative emissions) predicted by MOVES were insensitive to ambient temperature as compared with the tunnel measurements and the MOBILE- and EMFAC-predicted emission factors, resulting in underestimation of the measured NMHC/NO_x ratios at higher ambient temperatures. Although predicted NMHC/NO_x ratios are in good agreement with the measured ratios during cooler sampling periods, the measured NMHC/NO_x ratios are 3.1, 1.7, and 1.4 times higher than those predicted by the MOVES, MOBILE, and EMFAC models, respectively, during high-temperature periods. Although the MOVES NO_x emission factors were generally higher than the measured factors, most differences were not significant considering the variations in the modeled factors using alternative vehicle operating cycles to represent the driving conditions in the tunnel. The three models predicted large differences in NO_x and particle emissions and in the relative contributions of diesel and gasoline vehicles to total NO_x and particulate carbon (TC) emissions in the tunnel.

Implications: Although advances have been made to mobile source emission models over the past two decades, the evidence that mobile source emissions of carbon monoxide and hydrocarbons in urban areas were underestimated by as much as a factor of 2–3 in past inventories underscores the need for on-going verification of emission inventories. Results suggest that there is an overall increase in motor vehicle NMHC emissions on hot days that is not fully accounted for by the emission models. Hot temperatures and concomitant higher ratios of NMHC emissions relative to NO_x both contribute to more rapid and efficient formation of ozone. Also, the ability of EPA's MOVES model to simulate varying vehicle operating modes places increased importance on the choice of operating modes to evaluate project-level emissions.     

Quality Assured Measurements of Animal Building Emissions: Gas Concentrations

Abstract

Comprehensive field studies were initiated in 2002 to measure emissions of ammonia (NH₃), hydrogen sulfide (H₂S), carbon dioxide (CO₂), methane (CH₄), nonmethane hydrocarbons (NMHC), particulate matter <10 µm in diameter, and total suspended particulate from swine and poultry production buildings in the United States.

This paper focuses on the quasicontinuous gas concentration measurement at multiple locations among paired barns in seven states. Documented principles, used in air pollution monitoring at industrial sources, were applied in developing quality assurance (QA) project plans for these studies. Air was sampled from multiple locations with each gas analyzed with one high quality commercial gas analyzer that was located in an environmentally controlled on-farm instrument shelter. A nominal 4 L/min gas sampling system was designed and constructed with Teflon wetted surfaces, bypass pumping, and sample line flow and pressure sensors. Three-way solenoids were used to automatically switch between multiple gas sampling lines with ≥10 min sampling intervals. Inside and outside gas sampling probes were between 10 and 115 m away from the analyzers. Analyzers used chemiluminescence, fluorescence, photoacoustic infrared, and photoionization detectors for NH₃, H₂S, CO₂, CH₄, and NMHC, respectively. Data were collected using personal computer-based data acquisition hardware and software. This paper discusses the methodology of gas concentration measurements and the unique challenges that livestock barns pose for achieving desired accuracy and precision, data representativeness, comparability and completeness, and instrument calibration and maintenance.     

模拟成藏填埋垃圾有机质稳定化与产气的阶段性

通过人工构建模拟生物气藏的大型模拟生物反应器,研究模拟成藏填埋城市生活垃圾有机质厌氧降解及生物气化规律及其机理。结果表明,自然温度条件下,模拟填埋垃圾有机质降解和生物气化具有明显阶段性,与pH、ORP、温度等指标的阶段性变化存在相关性。产气阶段最佳条件包括:最适温度范围为31.0～36.0℃;最适pH范围为5.47～6.75,pH中性条件下产甲烷速率最高;ORP最适范围为-428～-541 mV,产甲烷高峰期ORP值为-519 mV,低于前人关于甲烷菌最适ORP的界定范围。每千克挥发性固体总生物气和甲烷产量分别为128.5 L和77.7 L,生物气和甲烷最大产气量分别为118.0 L/d和82.0 L/d,甲烷最大浓度为70.4%,产气高峰期与甲烷浓度高峰期同时出现。模拟成藏填埋垃圾有机质的稳定化过程具有明显的可诱导特征,关键因子的优化对有机质的降解及生物气化产生明显促进作用。     

Chlorinated Solvent Treatment Wetland

A first‐of‐its‐kind wetland restoration project was completed in October 2000 to treat trichloroethene‐(TCE‐)impacted groundwater from a former manufacturing facility prior to discharge into a highly valued recreational surface water body in the upper Midwest. This article summarizes the design, construction, operation, and effectiveness of the restored wetland. The groundwater‐surface water discharge zone at the site was restored as a wetland to improve the natural degradation of TCE and subsequent degradation by‐products. For the past 11 years, the treatment wetland performance was evaluated by monitoring the wetland vegetation, wetland hydraulics, and water chemistry. Water quality data have been used to assess the wetland geochemistry, TCE and TCE‐degradation by‐product concentrations within the wetland, and the surface water quality immediately downgradient of the wetland. The treatment wetland has been performing according to design, with TCE and TCE‐degradation by‐products not exceeding surface water criteria. The monitoring results show that TCE and TCE‐degradation by‐products are entering the treatment wetland via natural hydraulic gradients and that the geochemistry of the wetland supports both reductive dechlorination (anaerobic degradation) and cometabolic degradation (aerobic degradation) of TCE and TCE‐degradation by‐products: cis‐ and trans‐1,2‐dichloroethene and vinyl chloride. © 2013 Wiley Periodicals, Inc.     

Degradation of anti-inflammatory drug ketoprofen by electro-oxidation: comparison of electro-Fenton and anodic oxidation processes

The electrochemical degradation of the nonsteroidal anti-inflammatory drug ketoprofen in tap water has been studied using electro-Fenton (EF) and anodic oxidation (AO) processes with platinium (Pt) and boron-doped diamond (BDD) anodes and carbon felt cathode. Fast degradation of the parent drug molecule and its degradation intermediates leading to complete mineralization was achieved by BDD/carbon felt, Pt/carbon felt, and AO with BDD anode. The obtained results showed that oxidative degradation rate of ketoprofen and mineralization of its aqueous solution increased by increasing applied current. Degradation kinetics fitted well to a pseudo-first-order reaction. Absolute rate constant of the oxidation of ketoprofen by electrochemically generated hydroxyl radicals was determined to be (2.8?±?0.1)?×?10⁹ M^?1 s^?1 by using competition kinetic method. Several reaction intermediates such as 3-hydroxybenzoic acid, pyrogallol, catechol, benzophenone, benzoic acid, and hydroquinone were identified by high-performance liquid chromatography (HPLC) analyses. The formation, identification, and evolution of short-chain aliphatic carboxylic acids like formic, acetic, oxalic, glycolic, and glyoxylic acids were monitored with ion exclusion chromatography. Based on the identified aromatic/cyclic intermediates and carboxylic acids as end products before mineralization, a plausible mineralization pathway was proposed. The evolution of the toxicity during treatments was also monitored using Microtox method, showing a faster detoxification with higher applied current values.     

乙醇溶析结晶法从白炭黑废母液中回收硫酸钠

以乙醇为溶析剂,通过过滤—中和—蒸馏浓缩—溶析结晶等工序,从白炭黑废母液中回收硫酸钠。考察了硫酸钠回收效果的影响因素,并进行了热能消耗和处理成本的分析。实验结果表明：乙醇的加入量对硫酸钠溶解度和蒸馏浓缩过程有着显著影响;在蒸馏醇水比（乙醇与中性废母液的体积比）为0.27,浓缩废母液中硫酸钠质量浓度为69.27 g/L,溶析醇水比（乙醇与浓缩废母液的体积比）为1的最佳工艺条件下,白炭黑废母液中硫酸钠的一次回收率可达69.94%,硫酸钠产品的纯度达到97.3%。     

Microsporidia parasites disrupt the responses to cadmium exposure in a gammarid

Microsporidia parasites are commonly found in amphipods, where they are often asymptomatic, vertically-transmitted and have several effects on host sexuality and behaviour. As amphipods are often used as models in ecotoxicological studies, we investigated the effect of microsporidian infections on energy reserves and defence capacities of Gammarus roeseli under cadmium stress. Only females were infected by two microsporidia parasites: Dictyocoela roeselum or Dictyocoela muelleri. In physiological conditions, microsporidia had no major effect on energy reserves and defence capacities of G.?roeseli, while under cadmium exposure, energy reserves and antioxidant defence were weaker in infected females. Moreover, higher malondialdehyde levels detected in infected females revealed that they suffered more cellular damages. Our results suggest that microsporidia may affect gammarid fitness in stressful conditions, when parasitic stress cannot be compensated by the host. Consequently, microsporidia parasites should be a factor necessary to take into account in ecotoxicology studies involving amphipods.     

Effects of temperature on bacterial transport and destruction in bioretention media: field and laboratory evaluations

Microbial activities are significantly influenced by temperature. This study investigated the effects of temperature on the capture and destruction of bacteria from urban stormwater runoff in bioretention media using 2-year field evaluations coupled with controlled laboratory column studies. Field data from two bioretention cells show that the concentration of indicator bacteria (fecal coliforms and Escherichia coli) was reduced during most storm events, and that the probability of meeting specific water quality criteria in the discharge was increased. Indicator bacteria concentration in the input flow typically increased with higher daily temperature. Although bacterial removal efficiency was independent of temperature in the field and laboratory, column tests showed that bacterial decay coefficients in conventional bioretention media (CBM) increase exponentially with elevated temperature. Increases in levels of protozoa and heterotrophic bacteria associated with increasing temperature appear to contribute to faster die-off of trapped E. coli in CBM via predation and competition.     

Analysis of mixed halogenated dibenzo-p-dioxins and dibenzofurans (PXDD/PXDFs) in soil by gas chromatography tandem mass spectrometry (GC-MS/MS)

Mixed halogenated dibenzo-p-dioxins and dibenzofurans (PXDD/PXDFs, X = Br, Cl) are formed through combustion processes, and may be more toxic than their corresponding chlorinated and brominated analogues. With 4600 potential congeners, limited analytical standards, and complex environmental matrices, PXDD/PXDFs present a significant analytical challenge. Gas chromatography tandem mass spectrometry (GC-MS/MS) offers both selectivity and sensitivity through multiple reaction monitoring of unique transitions in a novel approach to PXDD/PXDF congener identification. Method validation was performed through analysis of soil samples obtained from a recycling plant fire. Of the PXDD/PXDFs examined, monobromo-dichlorodibenzofuran was the most prevalent, ranging in concentration from 8.6 ng g⁻¹ to 180 ng g⁻¹. Dibromo-dichlorodibenzo-p-dioxin, a compound of toxicological concern, ranged from 0.41 ng g⁻¹ to 10 ng g⁻¹. Concentrations of PXDD/PXDFs were between 6% and 10% that of the corresponding polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/PCDFs), with the exception of dibromo-dichlorodibenzo-p-dioxin concentrations, which were 36% that of tetrachlorodibenzo-p-dioxins. Higher levels of polybrominated PXDD/PXDFs may indicate a significant bromine source was present during combustion.     

Analysis of the toxicogenomic effects of exposure to persistent organic pollutants (POPs) in Slovakian girls: correlations between gene expression and disease risk

The chemical composition of persistent organic pollutants (POPs) in the environment is not uniform throughout the world, and these contaminants contain many structurally different lipophilic compounds. In a well-defined study cohort in the Slovak Republic, the POP chemicals present in the peripheral blood of exposed children were chemically analyzed. The chemical analysis data revealed that the relative concentration and profile of structurally different organic pollutants, including polychlorinated biphenyls (PCBs), 2,2′-bis(4-chlorophenyl)-1,1-dichloroethylene (p,p′-DDE), 2,2′-bis(4-chlorophenyl)-1,1,1-trichloro-ethane (p,p′-DDT), hexachlorobenzene (HCB) and β-hexachlorocyclohexane (β-HCH), may vary from individual to individual, even within the same exposure area. These chemicals can be broadly classified into two groups. The first group, the PCB congeners, primarily originated from industrial compounds and their byproducts. The second group of compounds originated from or was commonly used in the agricultural sector (e.g., DDT, HCB). The objective of this study was to examine the effects of the two POP exposure profiles on gene expression. For the study population, we selected pre-pubertal girls (mean age of 46.2 ± 1.4 months) with high POP concentrations in their blood (> 75% tile of total POP) and classified them in the high ‘PCB’ group when the total PCB concentration was significantly higher than the total concentration of other POP components and in the ‘Other Than PCB’ (OTP) group, when the total PCB concentration was significantly lower than the concentration of the other major POP constituents. A matched control group of girls (< 25% tile of total POP) was selected for comparison purpose (n = 5 per group). Our aims were to determine whether there were any common effects of high POP exposure at a toxicogenomic level and to investigate how exposure may affect physiological functions of the children in two different exposure scenarios. Global gene expression analysis using a microarray (Affymetrix Gene Chip Human genome U133 Plus 2.0 Array) platform was conducted on the total RNA of peripheral blood mononuclear cells from the girls. The results were analyzed by Partek GS, Louis, MI, which identified twelve genes (ATAD2B, BIVM, CD96, CXorf39, CYTH1 ETNK1, FAM13A, HIRA, INO80B, ODG1, RAD23B, and TSGA14) and two unidentified probe sets, as regulated differentially in both the PCB and OTP groups against the control group. The qRT-PCR method was used to validate the microarray results. The Ingenuity Pathway Analysis (IPA) software package identified the possible molecular impairments and disease risks associated with each gene set. Connective tissue disorders, genetic disorders, skeletal muscular disorders and neurological diseases were associated with the 12 common genes. The data therefore identified the potential molecular effects of POP exposure on a genomic level. This report underscores the importance of further study to validate the results in a random population and to evaluate the use of the identified genes as biomarkers for POP exposure.