Organophosphates in aircraft cabin and cockpit air--method development and measurements of contaminants

Methods for measurements and the potential for occupational exposure to organophosphates (OPs) originating from turbine and hydraulic oils among flying personnel in the aviation industry are described. Different sampling methods were applied, including active within-day methods for OPs and VOCs, newly developed passive long-term sample methods (deposition of OPs to wipe surface areas and to activated charcoal cloths), and measurements of OPs in high-efficiency particulate air (HEPA) recirculation filters (n = 6). In total, 95 and 72 within-day OP and VOC samples, respectively, have been collected during 47 flights in six different models of turbine jet engine, propeller and helicopter aircrafts (n = 40). In general, the OP air levels from the within-day samples were low. The most relevant OP in this regard originating from turbine and engine oils, tricresyl phosphate (TCP), was detected in only 4% of the samples (min-max 相似文献   

Report: waste refinery in the municipality of Bor?s.

This paper briefly describes waste treatment trends in Sweden and describes an example of state-of-the-art treatment in a local integrated waste treatment system (Bor?s). The focus is on treatment of household waste, to illustrate what can be done to establish a sustainable waste treatment system with high recovery of materials and energy. The various processes have resulted in a low amount of landfilled household waste, and high proportions of recovered energy and materials. Heat, electricity, vehicle fuel and fertilizers, metals and construction materials are recovered from the local waste in Bor?s, with less than 4% of domestic waste being sent to landfill.     

Oxidation of sulphite originating from flue gas desulphurization waste in soil

The rate of catalyzed oxidation of sulphite originating from flue gas desulphurization (FGD) waste was studied under varying conditions. The pH dependence was examined in aqueous solution at the pH range of 5 to 8, the effect of soil moisture was studied in sieved soil of different moisture contents, and the oxidation of sulphite to a soil as FGD waste, was measured at different depths in a field experiment. The experiments that the half-lives of sulphite in aqueous solution were between 0.5 and 2 hours and that the oxidation rate was highest at the lowest pH. In sieved soil the half-lives of sulphite were in the range of 3 to 20 days with the oxidation rate at the highest moisture content, indication that oxygen availability was the limiting factor. The slowest decrease of the sulphite concentration was found at a soil depth of 8–10 cm which was the where the highest background concentration of sulphite was found in control plots, too.Environmental Geochemistry and Health, 1988,10(1), 26–30     

The Effect of an Ergonomic Intervention on Musculoskeletal,Psychosocial and Visual Strain of VDT Entry Work: Organization and Methodology of the International Study

This special issue of the International Journal of Occupational Safety and Ergonomics (JOSE) reports the results from an extensive multinational and multidisciplinary collaborative investigation of the impacts on visual display terminal (VDT) work of musculoskeletal, visual, ergonomic, and psychosocial factors. For brevity, this effort has been referred to as the MEPS project (musculoskeletal—eyestrain—psychosocial—stress). This paper lays out the basic methodological structure of the study. The study was conducted in 4 countries utilizing VDT data entry workers as the primary subject population. A battery of objective and subject assessment measures, including muscle load, visual function, physical and visual strain, postural, ergonomic and psychosocial factors, were assessed at 3 different points in time. A pre-test was given prior to an ergonomic intervention. Two post-tests were given 1 month and 1 year after the ergonomic intervention.     

Determination of isocyanates, aminoisocyanates and amines in air formed during the thermal degradation of polyurethane

An air sampling method for the determination of isocyanates, aminoisocyanates and amines formed during the thermal degradation of polyurethane (PUR) is presented. The method is based on the collection of air samples using impinger flasks containing di-n-butylamine (DBA) in toluene with a glass fibre filter in series. Isocyanates are derivatized with DBA to urea derivatives, and amines are derivatized in a subsequent work-up procedure with ethyl chloroformate (ET) to carbamate esters. Amine, aminoisocyanate and isocyanate derivatives were characterized using liquid chromatography-time of flight mass spectrometry (LC-TOFMS) and liquid chromatography-chemiluminescent nitrogen detection (LC-CLND). Quantification was performed by LC-MS, monitoring molecular ions [MH]+ in the electrospray mode. The instrumental detection limits for amines, aminoisocyanates and isocyanates were in the ranges 30-40, 2-3 and 3-70 fmol, respectively. Thermal degradation products of PUR were observed in high concentrations during welding in district heating pipes and PUR-coated metal sheets. Eleven isocyanates, three amines and five aminoisocyanates were identified. The concentrations of isocyanates, aminoisocyanates and amines in samples collected in the smoke close to the welding spot were in the ranges 150-650, 4-290 and 1-70 ppb, respectively. In samples collected in the breathing zone, isocyanates and aminoisocyanates were observed in the ranges 9-120 and 4-19 ppb, respectively. The compounds were present in both gas and particle phases. Volatile compounds dominated in the gas phase, whereas less volatile compounds dominated in the particle phase. The method presented makes it possible to sample and determine amines and aminoisocyanates, in addition to isocyanates. The need to monitor these compounds is clearly illustrated by the high concentrations found during the thermal degradation of PUR.     

Determination of technical grade isocyanates used in the production of polyurethane plastics

A method for determination of technical grade isocyanates used in the production of polyurethane (PUR) is presented. The isocyanates in technical grade products were characterised as di-n-butylamine (DBA) derivatives using LC-MS and LC-chemiluminescent nitrogen detection (CLND) and the total isocyanate content was compared to a titration assay. For collection of isocyanates in air, an impinger-filter sampling technique with DBA as derivatisation reagent was used. Characterised DBA and nonadeuterium labelled DBA derivatives of isocyanates in technical products were used as calibration standards and internal standards, respectively, in the analysis of air samples. Three workplaces were studied where PUR products were produced either by spraying or by moulding. In both technical products and in air samples, a number of monomeric, oligomeric and prepolymeric isocyanates of e.g. methylenebisphenyl diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were characterised. Several of these have not previously been described in workplace atmospheres. In the technical isocyanate products, between 69 and 102% of the NCO content determined by titration was accounted for by LC-CLND. Quantifications of a wide range of isocyanates in air samples were performed with correlation coefficients in the range 0.988-0.999 (n= 8) and the instrumental detection limits were 0.7-25 pg. At the two workplaces where MDI- and HDI isocyanurate-based products were sprayed, the isocyanate composition in the air reflected the composition in the technical product. At the workplace where a MDI-based product was used in a moulding process, only the monomeric isocyanates were found in the air. The advantage of using characterised technical grade isocyanates as analytical standards was clearly demonstrated and the possibility of using index compounds when monitoring isocyanate exposure is discussed.     

Die Kristallstruktur des monoklinen α-Bi2O3

The Science of Nature -     

Tracing recovery from acidification in the western Norwegian Nausta watershed

A novel method, redundancy analysis (RDA), has been used to examine whether chemical recovery from acidification in the western Norwegian Nausta watershed produces detectable recovery within the community structure of the macro-zoobenthos. The RDA results have been compared with measures of recovery based on the changes detected using highly specialized and regionally defined biological acidity indices. We found that the beginning of biological recovery in the Nausta watershed was recognizable during the period 1989-1998. Recovery occurred in the upper reaches and in the tributaries. The multivariate approach proved to complement the acidity indices approach, and much biological information can be gained by their combined use. The RDA method is conservative, i.e. does not overestimate biological recovery, and it is not geographically constrained as are the acidity indices. We also found that seasonal climatic factors strongly influence the benthic community, and may confound the detection of the biological recovery process.