Partitioning and removal of dioxin-like congeners in flue gases treated with activated carbon adsorption

Activated carbon adsorption is commonly used to control dioxin-like congener (PCDD/Fs and PCBs) emissions. Partitioning of PCDD/Fs and PCBs between vapor and solid phases and their removal efficiencies achieved with existing air pollution control devices (APCDs) at a large-scale municipal waste incinerator (MWI) and an industrial waste incinerator (IWI) are evaluated via intensive stack sampling and analysis. Those two facilities investigated are equipped with activated carbon injection (ACI) with bag filter (BF) and fixed activated carbon bed (FACB) as major PCDD/F control devices, respectively. Average PCDD/F and PCB concentrations of stack gas with ACI+BF as APCDs are 0.031 and 0.006ng-TEQ/Nm(3), and that achieved with FACB are 1.74 and 0.19ng-TEQ/Nm(3) in MWI and IWI, respectively. The results show that FACB could reduce vapor-phase PCDD/Fs and PCBs concentrations in flue gas, while the ACI+BF can effectively adsorb the vapor-phase dioxin-like congener and collect the solid-phase PCDD/Fs and PCBs in the meantime. Additionally, the results of the pilot-scale adsorption system (PAS) experimentation indicate that each gram activated carbon adsorbs 105-115ng-PCDD/Fs and each surface area (m(2)) of activated carbon adsorbs 10-25ng-PCDD/Fs. Based on the results of PAS experimentation, this study confirms that the surface area of mesopore+macropore (20-200A) of the activated carbon is a critical factor affecting PCDD/F adsorption capacity.     

Bioaccessibility of polychlorinated biphenyls in workplace dust and its implication for risk assessment

Human exposure to bioaccessible PCBs via indoor dust is limited around the world. In the present study, the workplace dust sample from commercial office, hospital, secondary school, shopping mall, electronic factory and manufacturing plant were collected from Hong Kong for PCBs analyses. Total PCBs concentrations ranged from 46.8 to 249 ng g⁻¹, with a median of 107 ng g⁻¹. Manufacturing plant showed the highest concentration among all of sampling sites. PCB 77 was found as the dominant congeners. The bioaccessibility of PCBs in small intestinal juice ranging from 8.3% to 26.0% was significantly higher than that in gastric condition, ranging from 4.8% to 12.4%. In addition, significant negative correlations (p < 0.05) were observed between K_OW and bioaccessibility for all workplace dust samples. Risk assessment indicated that the averaged daily dose of dioxin-like PCBs via non-dietary intake of workplace dust, considering the bioaccessibility of PCBs, were much lower than the TDI of dioxins (2.3 pg WHO-TEQ kg bw⁻¹ d⁻¹) established by Joint FAO/WHO Expert Committee on Food Additives.     

The effects of perennial ryegrass and alfalfa on microbial abundance and diversity in petroleum contaminated soil

Enhanced rhizosphere degradation uses plants to stimulate the rhizosphere microbial community to degrade organic contaminants. We measured changes in microbial communities caused by the addition of two species of plants in a soil contaminated with 31,000 ppm of total petroleum hydrocarbons. Perennial ryegrass and/or alfalfa increased the number of rhizosphere bacteria in the hydrocarbon-contaminated soil. These plants also increased the number of bacteria capable of petroleum degradation as estimated by the most probable number (MPN) method. Eco-Biolog plates did not detect changes in metabolic diversity between bulk and rhizosphere samples but denaturing gradient gel electrophoresis (DGGE) analysis of PCR-amplified partial 16S rDNA sequences indicated a shift in the bacterial community in the rhizosphere samples. Dice coefficient matrices derived from DGGE profiles showed similarities between the rhizospheres of alfalfa and perennial ryegrass/alfalfa mixture in the contaminated soil at week seven. Perennial ryegrass and perennial ryegrass/alfalfa mixture caused the greatest change in the rhizosphere bacterial community as determined by DGGE analysis. We concluded that plants altered the microbial population; these changes were plant-specific and could contribute to degradation of petroleum hydrocarbons in contaminated soil.     

Risk assessment of trace elements in the stomach contents of Indo-Pacific Humpback Dolphins and Finless Porpoises in Hong Kong waters

The potential health risks due to inorganic substances, mainly metals, was evaluated for the two resident marine mammals in Hong Kong, the Indo-Pacific Humpback Dolphin (Sousa chinensis) and the Finless Porpoise (Neophocaena phocaenoides). The stomachs from the carcasses of twelve stranded dolphins and fifteen stranded porpoises were collected and the contents examined. Concentrations of thirteen trace elements (Ag, As, Cd, Co, Cr, Cs, Cu, Hg, Mn, Ni, Se, V and Zn) were determined by inductively coupled plasma mass spectrometer (ICP-MS). An assessment of risks of adverse effects was undertaken using two toxicity guideline values, namely the Reference Dose (RfD), commonly used in human health risk assessment, and the Toxicity Reference Value (TRV), based on terrestrial mammal data. The levels of trace metals in stomach contents of dolphins and porpoises were found to be similar. Risk quotients (RQ) calculated for the trace elements showed that risks to the dolphins and porpoises were generally low and within safe limits using the values based on the TRV, which are less conservative than those based on the RfD values. Using the RfD-based values the risks associated with arsenic, cadmium, chromium, copper, nickel and mercury were comparatively higher. The highest RQ was associated with arsenic, however, most of the arsenic in marine organisms should be in the non-toxic organic form, and thus the calculated risk is likely to be overestimated.     

Spatial distribution and vertical profile of polybrominated diphenyl ethers and hexabromocyclododecanes in sediment core from Tokyo Bay, Japan

Brominated flame retardants (BFRs), hexabromocyclododecanes (HBCDs) and polybrominated diethyl ethers (PBDEs) were detected in three sediment cores and six surface sediments of Tokyo Bay, Japan. HBCDs were detected for the first time in this region with concentrations ranging from 0.056 to 2.3 ng/g dry wt, implying their widespread contamination, even though their concentrations were lower than summation operatorPBDEs (di- to nona-BDEs) and BDE-209. Levels of these compounds were higher near to the highly populated industrial area of the bay implicating industrial and human activities as sources of these compounds. Summation operatorPBDEs increased in the sediment layer up to the mid-1990s and decreased afterwards, whereas BDE-209 showed an increasing trend until now, following the usage of different commercial BDE mixtures. HBCDs first appeared in the mid-1970s and increased until today. The annual surficial flux of HBCDs (0.62-2.4 ng/cm2/yr) is equal to summation operatorPBDEs (0.95-2.6 ng/cm2/yr) but lower than that of BDE-209 (17-58 ng/cm2/yr).     

A systemic health risk assessment for the chromium cycle in Taiwan

Health risk assessment (HRA) has been recognized as a useful tool for identifying health risks of human activities. In particular, this method has been well applied to spatially defined units, such as a production plant, a treatment facility, and a contaminated site. However, the management strategies based on the risk information will be more efficient if the comprehensive picture of total risks from all kinds of sources is depicted. In principle, the total risks can be obtained when all risk sources are assessed individually. Apparently, this approach demands huge amount of efforts. This study develops a methodology that combines substance flow and risk estimation to facilitate examination of risk in a systemic way and provide comprehensive understanding of risk generation and distribution corresponding to flows of substances in the anthroposphere and the environment. Substance flow analysis (SFA) and HRA method is integrated to produce a systemic risk assessment method, from which substance management schemes can be derived. In this study, the chromium cycle in Taiwan is used as an example to demonstrate the method, by which the associated substance flow in the economy and the risk caused by the substance in the environmental system is determined. The concentrations of pollutants in the environmental media, the resultant risks and hazard quotients are calculated with the widely-used CalTOX multimedia model.     

Assessment of some water quality parameters in the Red River downstream,Vietnam by combining field monitoring and remote sensing method

Environmental Science and Pollution Research - The Red River is the largest river in northern Vietnam, and it serves as the main water source for production and human activities in the Red River...     

Plastic waste as a valuable resource: strategy to remove heavy metals from wastewater in bench scale application

Environmental Science and Pollution Research - Single-use plastic waste is gradually considered a potential material for circular economy. Ion exchange resin obtained from polystyrene waste by...     

Surface functional characteristics (C, O, S) of waste tire-derived carbon black before and after steam activation

The effects of steam activation on the surface functional characteristics of waste tire-derived carbon black were investigated. Two carbon-based materials, powdered carbon black (PCB) and PCB-derived powdered activated carbon (PCB-PAC), were selected for this study. A stainless steel tubular oven was used to activate the PCB at an activation temperature of 900 degrees C and 1 atm using steam as an activating reagent. X-ray photoelectron spectroscopy (XPS) was adopted to measure the surface composition and chemical structure of carbon surface. Various elemental spectra (C, O, and S) of each carbon sample were further deconvoluted by peak synthesis. Results showed that the surfaces of PCB and PCB-PAC consisted mainly of C-C and C-O. The PCB-PAC surface had a higher percentage of oxygenated functional groups (C=O and O-C=O) than PCB. The O1s spectra show that the oxygen detected on the PCB surface was mainly bonded to carbon (C-O), whereas the oxygen on the PCB-PAC surface could be bonded to hydrogen (O-H) and carbon (C-O). Sulfur on the surface of PCB consisted of 58.9 wt% zinc sulfide (ZnS) and 41.1 wt% S=C=S, whereas that on the surfaces of PCB-PAC consisted mainly of S=C=S. Furthermore, the increase of oxygen content from 9.6% (PCB) to 11.9% (PCB-PAC) resulted in the increase of the pH values of PCB-PAC after steam activation.