Indoor air quality differences between urban and rural preschools in Korea

Background, aims, and scope

Preschool indoor air quality (IAQ) is believed to be different from elementary school or higher school IAQ and preschool is the first place for social activity. Younger children are more susceptible than higher-grade children and spend more time indoors. The purpose of this study was to compare the indoor air quality by investigating the concentrations of airborne particulates and gaseous materials at preschools in urban and rural locations in Korea.

Methods

We investigated the concentrations of airborne particulates and gaseous materials in 71 classrooms at 17 Korean preschools. For comparison, outdoor air was sampled simultaneously with indoor air samples. Airborne concentrations of total suspended particulates, respirable particulates, lead, asbestos, total volatile organic compounds and components, formaldehyde, and CO₂ were measured with National Institute for Occupational Safety and Health and/or Environmental Protection Agency analytical methods.

Results

The concentration profiles of the investigated pollutants in indoor and urban settings were higher than those in outdoor and rural areas, respectively. The ratios of indoor/outdoor concentrations (I/O) of particulates and gaseous pollutants were characterized in urban and rural preschools. Total dust concentration was highest in urban indoor settings followed by urban outdoor, rural indoor, and rural outdoor locations with an I/O ratio of 1.37 in urban and 1.35 in rural areas. Although I/O ratios of lead were close to 1, lead concentrations were much higher in urban than in rural areas. The I/O ratio of total VOCs was 2.29 in urban and 2.52 in rural areas, with the highest level in urban indoor settings. The I/O ratio of formaldehyde concentrations was higher in rural than in urban areas because the outdoor rural level was much lower than the urban concentration. Since an I/O ratio higher than 1 implies the presence of indoor sources, we concluded that there are many indoor sources in preschools.

Conclusions

We confirmed that pollutants in indoor and urban settings were higher than those in outdoor and rural areas, respectively. Preschool children are expected to spend more time inside preschool facilities and therefore to be more exposed to pollutants. As far as we know, preschool IAQ is different from elementary school or higher school IAQ. Also, they are more vulnerable than higher-grade children. We found that the indoor and urban concentration profiles of the studied pollutants in preschools were higher than those in outdoor and rural areas. We believe that our findings may be useful for understanding the potential health effects of exposure and intervention studies in preschools.     

An assessment of dust, endotoxin, and microorganism exposure during waste collection and sorting

This study was conducted to assess inhalation exposure to dust, endotoxin, and microorganisms (including viable bacteria, Gram-negative bacteria [GNB], and fungi) during waste collection and sorting; to identify factors affecting this exposure; and to estimate the gastrointestinal exposure to microorganisms. A total of 48 or 49 workers involved in collecting and sorting waste from households or the street were studied. Each worker carried two personal samplers in which filters were placed in the breathing zone for estimation of inhalation exposure. To assess the possibility of gastrointestinal exposure, microorganisms on the workers' faces were collected before and after work and compared with those collected from office workers. Inhalation exposure levels were categorized according to job title, waste type handled, and working conditions and were compared using analysis of variance. Multiple regression models were developed to identify those factors that substantially affected inhalation exposure. The average exposure level to total dust was 0.9 mg/m3 (range = 0.05 to 4.51 mg/m3), and the average exposure to endotoxin was 1123 EU/m3. The average respective exposure levels to bacteria, GNB, and fungi each exceeded 10(4) colony forming units (CFU)/m3. The multiple regression models found several factors that significantly explained the variation in levels of inhalation exposure to endotoxin and microorganisms; namely, sex (dust, bacteria, and GNB), job title (GNB and fungi), collection day (dust, bacteria, and GNB), temperature (endotoxin and GNB), humidity (endotoxin and fungi), and region (endotoxin) were significantly associated with exposure to these agents. In addition, the workers' faces were highly contaminated with microorganisms. In conclusion, inhalation exposure to endotoxin and microorganisms was high during waste collection and sorting, which may place workers at risk of developing various health problems, including respiratory complaints.     

Emission factors for high-emitting vehicles based on on-road measurements of individual vehicle exhaust with a mobile measurement platform

Fuel-based emission factors for 143 light-duty gasoline vehicles (LDGVs) and 93 heavy-duty diesel trucks (HDDTs) were measured in Wilmington, CA using a zero-emission mobile measurement platform (MMP). The frequency distributions of emission factors of carbon monoxide (CO), nitrogen oxides (NO(x)), and particle mass with aerodynamic diameter below 2.5 microm (PM2.5) varied widely, whereas the average of the individual vehicle emission factors were comparable to those reported in previous tunnel and remote sensing studies as well as the predictions by Emission Factors (EMFAC) 2007 mobile source emission model for Los Angeles County. Variation in emissions due to different driving modes (idle, low- and high-speed acceleration, low- and high-speed cruise) was found to be relatively small in comparison to intervehicle variability and did not appear to interfere with the identification of high emitters, defined as the vehicles whose emissions were more than 5 times the fleet-average values. Using this definition, approximately 5% of the LDGVs and HDDTs measured were high emitters. Among the 143 LDGVs, the average emission factors of NO(x), black carbon (BC), PM2.5, and ultrafine particle (UFP) would be reduced by 34%, 39%, 44%, and 31%, respectively, by removing the highest 5% of emitting vehicles, whereas CO emission factor would be reduced by 50%. The emission distributions of the 93 HDDTs measured were even more skewed: approximately half of the NO(x) and CO fleet-average emission factors and more than 60% of PM2.5, UFP, and BC fleet-average emission factors would be reduced by eliminating the highest-emitting 5% HDDTs. Furthermore, high emissions of BC, PM2.5, and NO(x) tended to cluster among the same vehicles.     

Implications of Conceptual Channel Representation on SWAT Streamflow and Sediment Modeling

Hydrologic modeling outputs are influenced by how a watershed system is represented. Channel routing is a typical example of the mathematical conceptualization of watershed landscape and processes in hydrologic modeling. We investigated the sensitivity of accuracy, equifinality, and uncertainty of Soil and Water Assessment Tool (SWAT) modeling to channel dimensions to demonstrate how a conceptual representation of a watershed system affects streamflow and sediment modeling. Results showed the amount of uncertainty and equifinality strongly responded to channel dimensions. On the other hand, the model performance did not significantly vary with the changes in the channel representation due to the degree of freedom allowed by the conceptual nature of hydrologic modeling in the parameter calibration. Such findings demonstrated good modeling performance statistics do not necessarily mean small output uncertainty, and partial improvements in the watershed representation may neither increase modeling accuracy nor reduce uncertainty. We also showed the equifinality and uncertainty of hydrologic modeling are case‐dependent rather than specific to models or regions, suggesting great caution should be used when attempting to transfer uncertainty analysis results to other modeling studies, especially for ungauged watersheds. Editor's note: This paper is part of the featured series on SWAT Applications for Emerging Hydrologic and Water Quality Challenges. See the February 2017 issue for the introduction and background to the series.     

Numerical study of heat transfer characteristics of char from waste tire pyrolysis

To investigate heat transfer of char from waste tire pyrolysis, the cooling of char was simulated by the computational fluid dynamics. To scrutinize the heat transfer characteristics, bed height, temperature of cooling wall, and mixing time were selected as calculation parameters. From the results, increasing the char bed height from 0.005 to 0.02 m, the total heat transfer is decreased as from 45.5 to 26.5 J. As the char bed height is further increased from 0.02 to 0.06 m, the total heat transfer is decreased from 26.5 to 9.1 J. The char bed height affects the total heat transfer significantly. The total heat transfer decreases from 15.9 to 14.0 J as the temperature of cooling wall increases from 273.15 to 323.15 K. The total heat transfer mildly depends on the temperature of cooling wall. The particle mixing time increases from 10 to 120 s and the total heat transfer decreases from 28.6 to 22.6 J. It is noted that the particle contact is enhanced between char particles as well as the particles and cooling wall as the particle mixing time decreases. Consequently, heat transfer is augmented.     

Evaluating the role of environmental quality in the sustainable rural economic development of England

The issue of the sustainable development of rural economies in England has recently received considerable attention. This is because many of the poorest areas in the country are rural, often of high environmental quality, but suffering from high unemployment and a lack of services and facilities. The rapid decline in agricultural incomes and in-migration of affluent urban workers since 1990 has exacerbated economic inequality in such areas. A number of factors have the potential to drive rural development and this paper applies, and considers, the feasibility of a method from the USA for combining economic and environmental variables in a regional growth model to examine the hypothesis that environmental quality is an important determinant of sustainable rural development in England. The model output suggests that, although environmental quality does play a role in sustainable rural development in England there are other, more important, factors driving development. These include business and communications infra-structure, the degree and opportunities for commuting and underlying employment prospects. The robustness and limitations of the method for combining economic and environmental variables is discussed in relation to the spatial interrelatedness of Local Authority Districts in England, and conclusions are drawn about areas for refinement and improvement of the method.

Alkali borosilicate glass by fly ash from a coal-fired power plant

The possibility of using coal fly ash as a silica source for alkali borosilicate glass was investigated. Alkali borosilicate glasses were prepared from the coal fly ash mixed with 30 wt.% reagents composed of Na(2)O and B(2)O(3) by susceptor-induction heating. Their densities ranged from 2.24 to 2.55 g cm(-3) and decreased as the amount of B(2)O(3) addition increased. However, the Vickers microhardness showed a different tendency with the density since the glass network connectivity improved by boron anomaly, which was identified by a nuclear magnetic resonance analysis. The Vickers microhardness of the glass product, with the addition of 15 wt.% B(2)O(3) and 15 wt.% Na(2)O, was about 4030 MPa. Furthermore, the changes in microstructure were consistent with those in the chemical stability by the toxicity characteristic leaching procedure (TCLP).     

Efficient dehalogenation of automobile shredder residue in NaOH/ethylene glycol using a ball mill

We investigated the effectiveness of sodium hydroxide/ethylene glycol (NaOH/EG) for dehalogenation of automobile shredder residue (ASR) using a ball mill. Efficient dehalogenation was achieved at atmospheric pressure by combining the use of EG (196 degrees C b.p.) as a replacement solvent for NaOH with ball milling, which improved contact between ASR and OH(-) in solution. Moderate NaOH concentrations and increased ball mill rotation speeds produced high dechlorination that was not significantly affected by the weight ratio of ASR to EG. NaOH/EG dechlorination increased with temperature with an apparent activation energy of 50 kJ mol(-1) confirming that the reaction proceeded under chemical reaction control. The modified shrinking-core model was appropriate to explain the dechlorination process. Low chloro levels in our NaOH/EG-treated ASR suggested that this material could be used for feedstock recycling and the wet process may be applicable for dehalogenation of other important waste streams.     

Enrichment of the metallic components from waste printed circuit boards by a mechanical separation process using a stamp mill

Printed circuit boards incorporated in most electrical and electronic equipment contain valuable metals such as Cu, Ni, Au, Ag, Pd, Fe, Sn, and Pb. In order to employ a hydrometallurgical route for the recycling of valuable metals from printed circuit boards, a mechanical pre-treatment step is needed. In this study, the metallic components from waste printed circuit boards have been enriched using a mechanical separation process. Waste printed circuit boards shredded to <10mm were milled using a stamp mill to liberate the various metallic components, and then the milled printed circuit boards were classified into fractions of <0.6, 0.6-1.2, 1.2-2.5, 2.5-5.0, and >5.0mm. The fractions of milled printed circuit boards of size <5.0mm were separated into a light fraction of mostly non-metallic components and a heavy fraction of the metallic components by gravity separation using a zig-zag classifier. The >5.0mm fraction and the heavy fraction were subjected to two-step magnetic separation. Through the first magnetic separation at 700 Gauss, 83% of the nickel and iron, based on the whole printed circuit boards, was recovered in the magnetic fraction, and 92% of the copper was recovered in the non-magnetic fraction. The cumulative recovery of nickel-iron concentrate was increased by a second magnetic separation at 3000 Gauss, but the grade of the concentrate decreased remarkably from 76% to 56%. The cumulative recovery of copper concentrate decreased, but the grade increased slightly from 71.6% to 75.4%. This study has demonstrated the feasibility of the mechanical separation process consisting of milling/size classification/gravity separation/two-step magnetic separation for enriching metallic components such as Cu, Ni, Al, and Fe from waste printed circuit boards.