Dissolved oxygen and dietary phosphorus modulate utilization and effluent partitioning of phosphorus in rainbow trout (Oncorhynchus mykiss) aquaculture

Phosphorus (P) is the limiting nutrient in freshwater primary production, and excessive levels cause premature eutrophication. P levels in aquaculture effluents are now tightly regulated. Increasing our understanding of waste P partitioning into soluble, particulate, and settleable fractions is important in the management of effluent P. When water supply is limited, dissolved oxygen concentration (DO) decreases below the optimum levels. Therefore, we studied effects of DO (6 and 10mg/L) and dietary P (0.7 and 1.0% P) on rainbow trout growth, P utilization, and effluent P partitioning. Biomass increased by 40% after 3 weeks. DO at 10mg/L significantly increased fish growth and feed efficiency, and increased the amount of P in the soluble fraction of the effluent. Soluble effluent P was greater in fish fed 1.0% P. DO increases fish growth and modulates P partitioning in aquaculture effluent.     

Long-term increases in surface water dissolved organic carbon: observations, possible causes and environmental impacts

Dissolved organic carbon (DOC) concentrations in 22 UK upland waters have increased by an average of 91% during the last 15 years. Increases have also occurred elsewhere in the UK, northern Europe and North America. A range of potential drivers of these trends are considered, including temperature, rainfall, acid deposition, land-use, nitrogen and CO2 enrichment. From examination of recent environmental changes, spatial patterns in observed trends, and analysis of time series, it is suggested that DOC may be increasing in response to a combination of declining acid deposition and rising temperatures; however it is difficult to isolate mechanisms based on monitoring data alone. Long-term DOC increases may have wide-ranging impacts on freshwater biota, drinking water quality, coastal marine ecosystems and upland carbon balances. Full understanding of the significance of these increases requires further knowledge of the extent of natural long-term variability, and of the natural "reference" state of these systems.     

Utility of stormwater monitoring.

Stormwater runoff is now a major contributor to the pollution of coastal waters in the United States. Public agencies are responding by requiring stormwater monitoring to satisfy the National Pollutant Discharge Elimination System stormwater permit. However, studies to understand the utility of the current programs or to improve their usefulness have not yet been performed. In this paper, we evaluate the land-use-based program, the industrial stormwater permit program, and beach water-quality monitoring in the County of Los Angeles, California, to determine if the results will be helpful to planners and regulators in abating stormwater pollution. The utility of the program has been assessed based on the programs' ability to accurately estimate the emissions for different classes of land use. The land-use program appears successful, while the industrial monitoring program does not. Beach water-quality monitoring suffers from a lack of real-time monitoring techniques. We also provide suggested improvements, such as sampling method and time, and parameter selection.     

Predictions by the Odor From Feedlots, Setback Estimation Tool (OFFSET) compared with observations by neighborhood monitors

A comparison between predicted and observed odor intensities at 20 neighborhood residences in the vicinity of seven various livestock farms in five different Minnesota counties was made to evaluate the Odor From Feedlots, Setback Estimation Tool (OFFSET) developed by the University of Minnesota. Observations by neighborhood monitors suggest that the OFFSET-predicted separation distances for annoyance-free frequencies of 99, 98, and 97% are large enough. The observations additionally indicate that predicted distances to obtain 94 and 91% annoyance-free frequencies may be large enough for some farms, but for other farms, greater distances may be needed. For two farms in the study, no significant difference between all of the observed and predicted intensities could be found. At four sites, a significant difference was found, and at three of these the difference was considerable. Odor emission rates used in the OFFSET model seem to describe the average emission fairly well for many odor sources, but improvement may be needed for some types of sources. Possible reasons for observations of annoying odor when not predicted include fluctuations in the odor emissions, wind speed fluctuations, topographic variation between sites, sensitivity differences by neighborhood monitors, and background emissions from other sources.     

Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 1. Stabilization performance of a continuous-flow reactor at low residence time.

There is increasing interest in the United States in producing biosolids from municipal wastewater treatment that meet the criteria for Class A designation established by the U.S. Environmental Protection Agency. Class A biosolids are intended to be free of pathogens and also must meet requirements for reduction of the vector-attraction potential associated with untreated sludge. High-temperature processes are considered to produce Class A biosolids if the combination of operating temperature and treatment time exceeds minimum criteria, but this option is not applicable to mixed, continuous-flow reactors. Such reactors, or any combination of reactors that does not meet the holding time requirement at a specific temperature, must be demonstrated to inactivate pathogens to levels consistent with the Class A criteria. This study was designed to evaluate pathogen inactivation by thermophilic anaerobic digestion in a mixed, continuous-flow reactor followed by batch or plug-flow treatment. In this first of a two-part series, we describe the performance of a continuous-flow laboratory reactor with respect to physical and chemical operating parameters; microbial inactivation in the combined continuous-flow and batch treatment system is described in the second part. Sludges from three different sources were treated at 53 degrees C, while sludge from one of the sources was also treated at 55 and 51 degrees C. Relatively short hydraulic retention times (four to six days) were used to represent a conservative operating condition with respect to pathogen inactivation. Treatment of a fermented primary sludge led to an average volatile-solids (VS) destruction efficiency of 45%, while VS destruction for the other two sources was near or below 38%, the Class A criterion for vector attraction reduction. Consistent with other studies on thermophilic anaerobic digestion of sludges at short residence times, effluent concentrations of volatile fatty acids (VFAs) were relatively high. Also consistent with other studies, the most abundant VFA in the effluent was propionate. Gas production ranged from 0.3 to 0.5 m3/kg VS fed and from 0.8 to 1.3 m3/kg VS destroyed.     

Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 2. Inactivation of pathogens and indicator organisms in a continuous-flow reactor followed by batch treatment.

Thermophilic-anaerobic digestion in a single-stage, mixed, continuous-flow reactor is not approved in the United States as a process capable of producing Class A biosolids for land application. This study was designed to evaluate the inactivation of pathogens and indicator organisms in such a reactor followed by batch treatment in a smaller reactor. The combined process was evaluated at 53 degrees C with sludges from three different sources and at 51 and 55 degrees C with sludge from one of the sources. Feed sludge to the continuous-flow reactor was spiked with the pathogen surrogates Ascaris suum and vaccine-strain poliovirus. Feed and effluent were analyzed for these organisms and for indigenous Salmonella spp., fecal coliforms, Clostridium perfringens spores, and somatic and male-specific coliphages. No viable Ascaris eggs were observed in the effluent from the continuous reactor at 53 or 55 degrees C, with greater than 2-log removals across the digester in all cases. Approximately 2-log removal was observed at 51 degrees C, but all samples of effluent biosolids contained at least one viable Ascaris egg at 51 degrees C. No viable poliovirus was found in the digester effluent at any of the operating conditions, and viable Salmonella spp. were measured in the digester effluent in only one sample throughout the study. The ability of the continuous reactor to remove fecal coliforms to below the Class A monitoring limit depended on the concentration in the feed sludge. There was no significant removal of Clostridium perfringens across the continuous reactor under any condition, and there also was limited removal of somatic coliphages. The removal of male-specific coliphages across the continuous reactor appeared to be related to temperature. Overall, at least one of the Class A pathogen criteria or the fecal coliform limit was exceeded in at least one sample in the continuous-reactor effluent at each temperature. Over the range of temperatures evaluated, the maximum time required to meet the Class A criteria by batch treatment of the continuous-reactor effluent was 1 hour for Ascaris suum and Salmonella spp. and 2 hours for fecal coliforms.     

Monitoring of the booster biocide dichlofluanid in water and marine sediment of Greek marinas

Dichlofluanid (N-dichlorofluoromethylthio-N'-dimethyl-N-phenylsulphamide) is used as booster biocide in antifouling paints. The occurrence of dichlofluanid and its metabolite DMSA (N'-dimethyl-N-phenyl-sulphamide) was monitored in seawater and marine sediment from three Greek marinas. Seawater and sediment samples were collected at three representative positions and one suspected hotspot in each marina and shipped to the laboratory for chemical analysis. As part of the project, an analytical method had been developed and validated. Furthermore, some additional experiments were carried out to investigate the potential contribution of paint particle bound dichlofluanid on the total concentration in the sediment. As expected, given its known high hydrolytic degradation rate, no detectable concentrations of dichlofluanid were measured in any of the seawater samples. DMSA was detected in seawater samples at very low concentrations varying from <3 ng l(-1) (LOD) to 36 ng l(-1). During method validation, it had already been demonstrated that dichlofluanid is unstable in sediment and can therefore only be determined as its metabolite DMSA. In a separate experiment, in which marine sediment was spiked with artificial paint particles containing dichlofluanid and then analysed according to the validated method, it was demonstrated that if there is any dichlofluanid originating from paint particles, this would be determined as DMSA. No DMSA was detected in any of the sediment samples. It could therefore be concluded that there were no significant concentrations of dichlofluanid in the sediment samples.     

Feral swine disturbance at important archaeological sites

Feral swine are well known as environmentally destructive invasive animals in many areas around the world, where they degrade native habitats, harm rare plant and animal species, damage agricultural interests, and spread disease. We provide the first quantification of their potential as agents of disturbance at archaeological sites. Our study was conducted in south-central Florida at Avon Park Air Force Range, a base comprising over 40,000 ha and containing many archaeological sites. To determine the identifiable prevalence of feral swine disturbance, we examined 36 sites registered with the Florida State Historic Preservation Office and also eligible for inclusion in the National Register of Historic Places (NRHP). Moreover, we evaluated the extent of swine disturbance at a prehistoric site of extraordinary significance to Florida’s prehistory, “Dead Cow.” Fifteen of the 36 NRHP-eligible sites (42 %) had some level of swine disturbance, including 14 of 30 (47 %) sites known to have artifacts within 20 cm of the surface (well within swine rooting depths). At the Dead Cow site, we documented disturbance at 74 % of shovel test points. Sites with shallow artifact depositions appeared highly vulnerable to disturbance by feral swine, threatening destruction of artifact stratigraphy and provenience. Our observations likely are a minimal representation of accumulated damage. These irreplaceable sites tell the area’s land use story across the millennia. That they are under threat from feral swine should serve broad notice of potential threats that feral swine may pose to archaeological sites globally, making effective swine management imperative for site protection.     

Pencycuron application to soils: degradation and effect on microbiological parameters

Clay loam soil from agricultural fields of alluvial (AL) soil (typic udifluvent) and coastal saline (CS) soil (typic endoaquept) were investigated for the degradation and effect of pencycuron application at field rate (FR), 2-times FR (2FR) and 10-times FR (10FR) with and without decomposed cow manure (DCM) on soil microbial variables under laboratory conditions. Pencycuron degraded faster in CS soil and in soil amended with DCM. Pencycuron spiking at FR and 2FR resulted in a short-lived (in case of 10FR slightly longer) and transitory toxic effect on soil microbial biomass-C (MBC), ergosterol content and fluorescein diacetate hydrolyzing activity (FDHA). Amendment of DCM did not seem to have any counteractive effect of the toxicity of pencycuron on the microbial variables. The ecophysiological status of the soil microbial communities as expressed by microbial metabolic quotient (qCO2) and microbial respiration quotient (Q(R)) changed, but for a short period, indicating pencycuron induced disturbance. The duration of this disturbance was slightly longer at 10FR. Pencycuron was more toxic to the metabolically activated soil microbial populations, specifically the fungi. It is concluded that side effects of pencycuron at 10FR on the microbial variables studied were only short-lived and probably of little ecological significance.     

Endocrine disruption of water and sediment extracts in a non-radioactive dot blot/RNAse protection-assay using isolated hepatocytes of rainbow trout

Goal, Scope and Background In order to evaluate the estrogenic activity of sediments and XAD water extracts of selected sites of the catchment area of the River Neckar, a river system in Southern Germany, an integrative assessment approach was used to assess the ecological hazard potential of endocrine-disrupting compounds in sediment and water. Methods The approach is based on estrogen receptor-mediated vitellogenin synthesis induced in isolated hepatocytes of rainbow trout and quantified in a non-radioactive dot blot/RNAse protection-assay in parallel to comprehensive chemical analyses of estrogenic substances. Results and Discussion Numerous investigated extracts revealed an estrogen activity comparable to that of the positive control (1 nM 17?-estradiol corresponding to 270 ng/L in the test medium). Based on a concentration factor of 30 in the extracts and a recovery of XAD resins of approximately 80 %, 17?-estradiol equivalent concentrations between 20 and 26.7 ng/L could be calculated downstream of a sewage treatment plant (< 0.1 ng/L for a reference site). A comparison of the bioassay-derived Bio-TEQs (toxicity equivalents) and the Chem-TEQs revealed a high correlation with a Pearson coefficient of 0.85, indicating that the same ranking of the samples could be obtained with respect to the endocrine disrupting potential with both chemical and bioanalytical analysis. However, the TEQ concentrations computed from chemical analyses were significantly lower than the bioassay-derived TEQ concentrations. In fact, in none of the samples, more than 14 % of the vitellogenin-inducing potency could be attributed to the substances (steroids, alkylphenols, bisphenol A, diethylstilbestrol) analyzed. A comparison of the endocrine disrupting potential of sediments extracted by the solvents acetone and methanol revealed lower biological effects for acetone-extracted samples. Possible reasons may be a masking of endocrine effects in acetone extracts by cytotoxicity, a low extraction efficiency of the solvent acetone, or anti-estrogen potencies of some extracted sediment compounds. Using a mass balance approach, the contribution of the compounds analyzed chemically (Chem-TEQs) to the total endocrine activity (Bio-TEQs) was calculated. Based on the very low detection limits, particularly of the steroids with their high TEF factors, results revealed that a calculation of the Chem-TEQs is associated with considerable scale inaccuracy: Whereas only 7-15 % of the biological effectiveness (Bio-TEQs) could be explained by endocrine substances identified above the detection limits, the assumption of concentrations slightly below the given detection limits would result in a significant over estimation (137-197 %) of the Bio-TEQs. Even the interassay variation of the dot blot assay with different fish donors for primary hepatocyte (factor 2 - 2.5) is relatively low, when compared to the large range of the Chem-TEQ concentrations (factor 20) obtained when applying different modes of calculation. Conclusions and Outlook Overall, only a minor portion of the endocrine activity detected by bioassays could be linked to compounds identified by chemical analysis. In vitro assays for assessment of endocrine activities are useful as sensitive integrating methods that provide quantitative estimates of the total activity of particular receptor-mediated responses. Although discrepancies may also result from different bioanalytical approaches, it is overall likely that bioanalytical and not chemical analytical approaches give the correct estimate of endocrine disrupting potencies in environmental samples. As a conclusion, assessment of endocrine disruption based on chemical analysis alone does not appear sufficient and further research into the spectrum of substances with potential endocrine activity as well as into additive or even synergistic effects in complex environmental samples is urgently needed.