炼油废水污泥脱水工艺条件的优化

采用化学除油降黏—污泥调理—离心脱水工艺处理某炼油厂废水处理系统的混合污泥,并对工艺条件进行优化。实验结果表明,最佳的工艺条件为：化学除油降黏阶段处理体系的pH=4,反应温度35 ℃,H₂O₂加入量 2 g/L,m（H₂O₂）∶ m（Fe²⁺）=4,反应时间 60 min;污泥调理反应阶段的CaO加入量7.0 g/L;离心脱水阶段在分离因数为1 558时脱水5 min。在此条件下,得到的泥饼的含水率为70.0%~75.0%（w）,含油率小于2%（w）,污泥比阻约为3.0×10⁷ s²/g。     

磷石膏水热法合成硫酸钙晶须

以磷石膏为原料,二水合硫酸钙、硫酸镁、甘油为添加剂,采用水热法合成硫酸钙晶须,考察了料浆含量、反应温度、反应时间、体系pH等因素对晶须的直径和长径比的影响;并采用SEM技术观察硫酸钙晶须的形貌。实验结果表明,当磷石膏含量2.5%（w）、反应温度130 ℃、反应时间4 h、体系pH 4时,制备得到的硫酸钙晶须长径比为56.24,平均直径为0.17 μm。SEM表征结果显示,硫酸钙晶须形貌规整、分散均匀、直径较小,达百纳米级。     

Effect of temperature and particle size on the thermal desorption of PCBs from contaminated soil

Thermal desorption is widely used for remediation of soil contaminated with volatiles, such as solvents and distillates. In this study, a soil contaminated with semivolatile polychlorinated biphenyls (PCBs) was sampled at an interim storage point for waste PCB transformers and heated to temperatures from 300 to 600 °C in a flow of nitrogen to investigate the effect of temperature and particle size on thermal desorption. Two size fractions were tested: coarse soil of 420–841 μm and fine soil with particles <250 μm. A PCB removal efficiency of 98.0 % was attained after 1 h of thermal treatment at 600 °C. The residual amount of PCBs in this soil decreased with rising thermal treatment temperature while the amount transferred to the gas phase increased up to 550 °C; at 600 °C, destruction of PCBs became more obvious. At low temperature, the thermally treated soil still had a similar PCB homologue distribution as raw soil, indicating thermal desorption as a main mechanism in removal. Dechlorination and decomposition increasingly occurred at high temperature, since shifts in average chlorination level were observed, from 3.34 in the raw soil to 2.75 in soil treated at 600 °C. Fine soil particles showed higher removal efficiency and destruction efficiency than coarse particles, suggesting that desorption from coarse particles is influenced by mass transfer.     

Some technical issues in managing PCBs

Polychlorinated biphenyls (PCBs) were important industrial chemicals featuring high thermal and chemical stability and low flammability. They were widely used as dielectric and thermal fluid in closed electro-technical applications (transformers, capacitors…) and also in numerous dispersive uses, ranking from auto-copying paper to sealant or coatings. During the 1960s, severe environmental consequences started becoming apparent. The stability of PCBs contributed to their persistence in the environment, their lipophilic character to bio-magnification. Fish-eating species seemed threatened in their existence. In Japan and in Taiwan, thousands of people consumed PCB-contaminated oil. The production of PCBs stopped completely during the 1980s. Usage could continue in closed applications only. In this paper, particular attention is given to two issues: the cleaning of PCB electric transformers and the potential impact of PCB-containing building materials. Other contributions will cover the management and treatment of PCB-contaminated soil, sludge or fly ash. The complete survey is being prepared by request of the Knowledge Center for Engineers and Professionals.     

Environmental monitoring of alcohol sulfates and alcohol ethoxysulfates in marine sediments

The study describes the environmental monitoring of anionic surfactants―alcohol sulfates (AS) and alcohol ethoxysulfates (AES)—in marine sediments. Concentration values were obtained after pressurised liquid extraction (PLE) and liquid chromatography–tandem mass spectrometry analysis (LC–MS/MS). Samples were collected from a range of wastewater discharge points along the coast of the provinces of Huelva, Málaga, Granada and Almería. Urban, agricultural and industrial wastewaters are discharged at the selected 38 sampling sites. Principal component analysis was carried out in order to evaluate the distribution and behaviour of these compounds in these coastal environments. Evaluation of the data revealed that the behaviour and sources of AS and AES in marine sediments are different, and that the distribution of AES depends on the length of the alkyl chain, while the number of ethoxylated units is not relevant. Additionally, the 38 sampling sites can be grouped into only two types of outfalls according to their AS distribution. The concentration of compounds in sediment samples ranged from 7.52 to 13.50 mg kg^?1 for AS, from 3.04 to 10.68 mg kg^?1 for AES–C₁₂E_x and from 3.83 to 11.56 mg kg^?1 for AES–C₁₄E_x.     

Degree of phosphorus saturation of an Oxisol amended with biosolids in a long-term field experiment

When applied to agricultural soils, phosphate fertilizers and the mineral or organic compounds present in solid and/or liquid waste may raise phosphorus (P) content and increase soil P saturation. The degree of phosphorus saturation (DPS) is a good indicator of potential P loss from agricultural soils. The purpose of this study was to calculate the DPS of samples from an Oxisol amended for 5 years with biosolids and mineral fertilizer. DPS was calculated based on P, iron, and aluminum extracted by ammonium oxalate and oxalic acid (DPS_ox) or by Mehlich-1 solution (DPS_M1). Treatments included NPK mineral fertilization (175 kg ha^?1 of P), B1?=?19.02 t ha^?1 of biosolids (350 kg ha^?1 of P), B2?=?38.17 t ha^?1 of biosolids (703 kg ha^?1 of P), B3?=?76.26 t ha^–1 of biosolids (1,405 kg ha^?1 of P), and a control (no P added). Water-extractable P (WEP) was also measured. Critical levels of DPS_ox and DPS_M1 (21 and 24 %, respectively) were only achieved in the topsoil (0–0.1 m) at the highest biosolid dose. Concentration of WEP was positively correlated to DPS_ox and DPS_M1. The DPS_M1 method may be an alternative to DPS_ox for assessing the environmental risk of P loss from soil into surface runoff.     

混凝-超滤短流程工艺处理北方水库原水简

采用混凝-超滤膜短流程工艺对大伙房水库原水进行处理,考察其除污染性能和膜污染情况,并对该短流程工艺参数进行优化。结果表明,当利用超滤膜直接过滤原水时,膜污染较重,并且对污染物质的去除率较低;而采用混凝-超滤短流程工艺时,膜污染得到一定程度上的缓解;当絮凝剂投加量为7 mg/L、膜清洗周期为30 min时,对浊度、COD_Mn和UV₂₅₄的去除率分别为95.61%、40.42%和37.12%,出水水质能够满足生活饮用水卫生标准。     

活性炭纤维负载TiO2催化剂的制备及其电催化性能

采用溶胶-凝胶法制备了活性炭纤维负载TiO₂催化剂（TiO₂/ACF）,并通过SEM和XRD等手段对TiO₂/ACF进行了表征。以邻苯二甲酸二甲酯（DMP）为目标降解物,考察了催化材料的电催化活性。实验结果表明：在反应温度为25 ℃、初始DMP质量浓度为100.0 mg/L、电解质Na₂SO₄质量浓度为100 mg/L、电流密度为62.5 mA/cm²、电极板间距为4 cm的条件下,经过40 min的降解,DMP质量浓度为1.8 mg/L,DMP去除率为98.2%;TiO₂/ACF在反应过程中可以原位再生,经6次重复使用后仍保持很高的催化活性,对DMP的去除率仍达90%以上。     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.     

罐底含油泥热解动力学参数计算方法的优选

在化学反应设计中反应动力学是较重要的因素。为得到更合理的污泥热解动力学参数计算方法,利用热重分析仪,在氮气气氛下对罐底含油污泥的热解特性进行研究。根据热重实验数据,分别采用Coats-Redfern法、Kissinger法、FWO法和Popescu法计算污泥热解动力学参数,并获取罐底泥热解制油的主要阶段(第2阶段)的反应活化能E、频率因子A并分析各种方法反应机理。通过对比不同计算方法得到动力学参数及拟合曲线与实验曲线的相关性,确定了最佳罐底含油污泥热解动力学参数计算方法。研究表明,Popescu法得到罐底泥的热解过程符合Jander方程,活化能E为101.43 kJ/mol,与FWO法得到的91.20 kJ/mol相近,且预测曲线与实验曲线有较好的相关性(0.9816),说明Popescu法计算罐底泥热解动力学参数更合适。