炼油废水污泥脱水工艺条件的优化

采用化学除油降黏—污泥调理—离心脱水工艺处理某炼油厂废水处理系统的混合污泥,并对工艺条件进行优化。实验结果表明,最佳的工艺条件为：化学除油降黏阶段处理体系的pH=4,反应温度35 ℃,H₂O₂加入量 2 g/L,m（H₂O₂）∶ m（Fe²⁺）=4,反应时间 60 min;污泥调理反应阶段的CaO加入量7.0 g/L;离心脱水阶段在分离因数为1 558时脱水5 min。在此条件下,得到的泥饼的含水率为70.0%~75.0%（w）,含油率小于2%（w）,污泥比阻约为3.0×10⁷ s²/g。     

盐酸脱附Pb(Ⅱ)负载氨基膦酸树脂的基本性能

氨基膦酸树脂是一种常用的广谱性重金属螯合树脂,对水中的Pb(Ⅱ)具有很好的选择性分离去除能力,但吸附Pb(Ⅱ)后的树脂再生较为困难。系统研究了盐酸脱附Pb(Ⅱ)-负载氨基膦酸树脂D860的基本性能,优化了基本脱附参数。实验表明,采用盐酸作为脱附剂具有较为良好的脱附效果,10%吸附量树脂脱附反应平衡较快仅需10 min,脱附本身受Pb(Ⅱ)在盐酸溶液中的溶解度影响显著。脱附流速从1 BV/h升高到5 BV/h,脱附效果受到的影响很小。升高温度可以提高PbCl2溶解度,进而提高脱附效率。固定床脱附采用1.0 mol/L盐酸,在1 BV/h和303 K条件下,仅需7 BV脱附剂即可实现较高的脱附效率。     

罐底含油泥热解动力学参数计算方法的优选

在化学反应设计中反应动力学是较重要的因素。为得到更合理的污泥热解动力学参数计算方法,利用热重分析仪,在氮气气氛下对罐底含油污泥的热解特性进行研究。根据热重实验数据,分别采用Coats-Redfern法、Kissinger法、FWO法和Popescu法计算污泥热解动力学参数,并获取罐底泥热解制油的主要阶段(第2阶段)的反应活化能E、频率因子A并分析各种方法反应机理。通过对比不同计算方法得到动力学参数及拟合曲线与实验曲线的相关性,确定了最佳罐底含油污泥热解动力学参数计算方法。研究表明,Popescu法得到罐底泥的热解过程符合Jander方程,活化能E为101.43 kJ/mol,与FWO法得到的91.20 kJ/mol相近,且预测曲线与实验曲线有较好的相关性(0.9816),说明Popescu法计算罐底泥热解动力学参数更合适。     

不同运行模式对同步脱氮除磷CAST工艺快速启动及其稳定维持的影响

以实际生活污水为处理对象,考察了传统进水/曝气和改良型分段进水的交替缺氧-好氧(A/O)2种运行模式对CAST工艺的快速启动及脱氮除磷性能稳定维持的影响。结果表明,传统进水/曝气运行模式下,系统达到最佳营养物去除性能所需启动时间30 d,稳定运行阶段TN平均去除80.66%,磷的去除率维持在66.30%左右;采用改良型交替运行模式,反应器达到稳定运行状态仅需18 d,系统稳定运行时TN平均去除81.36%,磷去除率稳定维持在90%以上,出水磷浓度在0.3 mg/L以下,出水水质达到国家污水综合排放标准一级A(GB8978-2002)。研究还发现,传统运行模式下,由低温引起的污泥沉降性能变差导致系统污泥严重流失,反应器几乎丧失污染物去除性能;而低温对交替运行模式下的反应器除磷性能几乎没有影响,总氮去除则因氨氮不完全硝化而大大降低。     

电镀污泥的热处理特性以及对金属回收的影响

焙烧-酸浸法可有效回收电镀污泥中的有价金属,而污泥的热处理特性是决定能否采用焙烧预处理的重要因素。研究了氧化焙烧和还原焙烧对污泥成分和金属浸出性的影响,并对焙烧前后的污泥进行了金属形态分析和X射线衍射(XRD)分析。结果表明,焙烧预处理实现了污泥减量和金属富集;ES1经氧化焙烧后金属浸出率接近原泥,Cu的浸出率达99%;ES2的还原焙烧效果优于氧化焙烧,特别是Cu的浸出率超过97%,XRD分析发现,还原焙烧过程中金属Cu被还原为铁铜合金;2种焙烧均造成了ES3中目标金属Ni的浸出率的降低;金属浸出性的下降与残渣态的形成有关。     

Development of IC-ELISA for detection of organophosphorus pesticides in water

Diethyl (carboxymethyl) phosphonate (DECP) was used as the hapten to develop an indirect competitive enzyme-linked immunosorbent assay (IC-ELISA) for detecting organophosphorus pesticides (OPs). Conjugator of DECP with bovin serum albumin (BSA) was used as the immunogen for producing the polyclonal antibodies (PcAbs). Three antisera were obtained after the immune procedure. Characterization studies of the PcAbs indicated that the titer of antiserum-1 was highest in 3 antisera, and antiserum-1 had high affinity and specificity to the parathion, dichlorvos and pirimiphos. The IC-ELISA showed an IC₅₀ of 0.428 μ g/mL with a detection limit of 0.0125 μ g/mL to parathion. The assay also indicated that the IC₅₀ values of pirimiphos and dichlorvos were 0.331 μ g/mL and 1.25 μ g/mL respectively, and the detection limits of pirimiphos and dichlorvos were 0.0116 μ g/mL and 0.048 μ g/mL respectively. Recoveries of parathion, pirimiphos and dichlorvos spiked into water samples ranged from 90% to 160%. The results indicated that the ELISA could be a convenient and supplemental analytical tool for monitoring OPs residues in environmental water samples.     

Structural changes in soil communities after triclopyr application in soils invaded by Acacia dealbata Link

Triclopyr is a commonly used herbicide in the control of woody plants and can exhibit toxic effects to soil microorganisms. However, the impact on soils invaded by plant exotics has not yet been addressed. Here, we present the results of an 18-month field study conducted to evaluate the impact of triclopyr on the structure of fungal and bacterial communities in soils invaded by Acacia dealbata Link, through the use of denature gradient gel electrophoresis. After triclopyr application, analyses of bacterial fingerprints suggested a change in the structure of the soil bacterial community, whereas the structure of the soil fungal community remained unaltered. Bacterial density and F:B ratio values changed across the year but were not altered due to herbicide spraying. On the contrary, fungal diversity was increased in plots sprayed with triclopyr 5 months after the first application. Richness and diversity (H´) of both bacteria and fungi were not modified after triclopyr application.     

Evaluation of Regenerative-air Vacuum Street Sweeping on Geological Contributions to PM10

Street sweeping is often proposed as a means of reducing the emissions from paved roads. The objective of this study was to evaluate the effectiveness of street sweeping on ambient particulate matter concentrations and to determine the difference In source contributions to PM10 concentrations between street sweeping and non-street sweeping periods.

Chemically-speciated measurements of PM10 and PM2.5 were taken in the commercial section of Reno, Nevada, for a one-month sampling period. The Chemical Mass Balance (CMB) model was applied to these data and an average of approximately 50 percent of the PM10 was apportioned to resuspended geological material. During half of the sampling period, streets In the vicinity of the sampling site were completely swept with a regenerative-air vacuum sweeper, while no sweeping was performed during the remainder of the experiment. Ratios of primary geological contributions divided by primary motor vehicle contributions to PM10 were compared between sweeping and non-sweeping periods using analysis of variance. This ratio of source contributions minimizes the effects of variations in traffic volume and meteorological dispersion. No significant differences in geological contributions to PM10 were detected as a result of regenerative-air vacuum street sweeping.     

Rotary Kiln Incineration of Dichloromethane and Xylene: A Comparison of Incinerability Characteristics Under Various Operating Conditions

Comparisons are made, for the first time, between the combustion characteristics of dichloromethane and xylene in an industrial rotary kiln incinerator. The comparisons are made under different operating conditions, including variable kiln rotation rate and operation both with and without turbulence air. Continuous gas composition and temperature measurements and batch gas composition measurements were obtained from two vertical locations hear the exit region of the rotary kiln. The measurements show that there is significant vertical stratification at the exit of the kiln. Addition of turbulence air enhanced combustion conditions throughout the kiln during xylene processing. During dichloromethane processing, however, the addition of turbulence air had minimal effect and only promoted greater bulk mixing; chlorinated compounds transported from the lower kiln during operation with turbulence air were not efficiently processed in the upper kiln. Evolution of test liquids from the bed was not constant but rather was characterized by intermittent peaks. The field-scale data of this work suggest that the evolution rate of the test liquid was increased as kiln rotation rate increased. Many of the differences between xylene and dichloromethane processing during these experiments are explained by a simple stoichiometric analysis.     

Treatment of 1,3-Butadiene in an Air Stream by a Biotrickling Filter and a Biofilter

ABSTRACT

This paper presents results obtained from a performance study on the biotreatment of 1,3-butadiene in an air stream using a reactor that consisted of a two-stage, in-series biotrickling filter connected with a three-stage, in-series biofilter. Slags and pig manure-based media were used as packing materials for the biotrickling filter and the biofilter, respectively. Experimental results indicated that, for the biotrickling filter portion, the butadiene elimination capacities were below 5 g/m³/hr for loadings of less than 25 g/m³/hr, and the butadiene removal efficiency was only around 17%. For the biofilter portion, the elimination capacities ranged from 10 to 107 g/m³/hr for loadings of less than 148 g/m³/hr. The average butadiene removal efficiency was 75–84% for superficial gas velocities of 53–142 m/hr and a loading range of 10–120 g/m³/hr. The elimination capacity approached a maximum of 108 g/m³/hr for a loading of 150 g/m³/hr. The elimination rates of butadiene in both the biotrickling filter and biofilter were mass-transfer controlled for influent butadiene concentrations below about 600 ppm for superficial gas velocities of 29–142 m/hr. The elimination capacity was significantly higher in the biofilter than in the biotrickling filter. This discrepancy may be attributed to the higher mass-transfer coefficient and gas-solid interfacial area offered for transferring the gaseous butadiene in the biofilter.