二乙烯三胺五甲叉膦酸酸解磷尾矿的实验探究

为减少磷尾矿堆积带来的环境污染问题,实现磷尾矿的钙、镁、磷元素的分离,以高镁磷尾矿为原料,采用二乙烯三胺五甲叉膦酸(DTPMP)进行酸解,探究磷尾矿中主要物相在DTPMP中的分解机制,并通过单因素实验探究pH、反应时间、反应温度及投料比对磷尾矿中MgO、CaO和P_2O_5分解率的影响。实验结果表明:pH对P_2O_5的分解率影响较大,高温更有利于尾矿中镁的溶出,在pH为2. 5,反应时间为60 min,反应温度为80℃,投料比为1. 56时,MgO、CaO和P_2O_5的分解率分别达到61. 05%、38. 23%和9. 67%。     

建筑垃圾堆放点样本集构建与优化研究

为更好地解决手工制作的建筑垃圾堆放点样本集效率低、数据量少,难以支撑基于深度学习的遥感图像目标检测算法训练需求的问题,采用基于像素的遥感分类方法构建建筑垃圾堆放点样本集,在此基础上结合直方图均衡化,CS-LBP算子约束以及迁移学习的方法对Wasserstein生成对抗模型（WGAN）进行优化,实现了样本集扩充。研究结果表明:相对于纯手工制作的样本集,基于像素的遥感分类方法可以显著提升样本集制作的效率;同时,经过WGAN优化后,生成样本模拟了原始数据的颜色与纹理特征分布规律,增加了原始数据的多样性,满足了扩充样本集的需求。     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

On-going nitrification in chloraminated drinking water distribution system (DWDS) is conditioned by hydraulics and disinfection strategies

Within the drinking water distribution system (DWDS) using chloramine as disinfectant, nitrification caused by nitrifying bacteria is increasingly becoming a concern as it poses a great challenge for maintaining water quality. To investigate efficient control strategies, operational conditions including hydraulic regimes and disinfectant scenarios were controlled within a flow cell experimental facility. Two test phases were conducted to investigate the effects on the extent of nitrification of three flow rates (Q = 2, 6, and 10 L/min) and four disinfection scenarios (total Cl₂=1 mg/L, Cl₂/NH₃-N=3:1; total Cl₂=1 mg/L, Cl₂/NH₃-N=5:1; total Cl₂=5 mg/L, Cl₂/NH₃-N=3:1; and total Cl₂=5 mg/L, Cl₂/NH₃-N=5:1). Physico-chemical parameters and nitrification indicators were monitored during the tests. The characteristics of biofilm extracellular polymetric substance (EPS) were evaluated after the experiment. The main results from the study indicate that nitrification is affected by hydraulic conditions and the process tends to be severe when the fluid flow transforms from laminar to turbulent (2300<Re<4000). Increasing disinfectant concentration and optimizing Cl₂/NH₃-N mass ratio were found to inhibit nitrification to some extend when the system was running at turbulent condition (Q = 10 L/min, Re = 5535). EPS extracted from biofilm that was established at the flow rate of 6 L/min had greater carbohydrate/protein ratio. Furthermore, several nitrification indicators were evaluated for their prediction efficiency and the results suggest that the change of nitrite, together with total organic carbon (TOC) and turbidity can indicate nitrification potential efficiently.     

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.     

长江流域2000—2015年生态系统质量及服务变化特征

分析生态系统质量与服务现状及变化特征,有助于准确了解流域生态系统状况与趋势,为流域生态保护与修复的高效管理提供参考依据.采用相对生物量密度与相对植被覆盖度指数以及生态系统服务（土壤保持、防风固沙、洪水调蓄、粮食生产）评估模型,评估2000—2015年长江流域生态系统质量及服务变化特征.结果表明:①2000—2015年,长江流域森林、灌丛以及草地生态系统质量提升显著,56.56%的森林、45.65%的灌丛以及19.26%的草地生态系统质量得到不同程度的提高.②研究期间,长江流域粮食生产、洪水调蓄、土壤保持、防风固沙均呈显著上升趋势,其中粮食生产能力增加13.7%,洪水调蓄功能提升10.1%,土壤保持服务提高19.5%,防风固沙总量增加30.0%.③长江流域生态系统质量不高,处于低与差质量等级的生态系统面积比例在25%~35%之间;受不同类型的自然和人类活动影响,长江流域生态系统质量与服务均存在局部退化现象.研究显示,在生态质量与服务评估的基础上,分区域、分类型实施不同的生态系统保护与恢复途径,是今后长江流域加强生态系统管理的重要途径.      

基于PCA-SOM的北京市平谷区地下水污染溯源

为了解北京市平谷区地下水污染物来源,以平谷区2010—2018年监测数据为基础,使用PCA(主成分分析法)识别了地下水水质指标因子,使用自组织映射识别了污染物的空间分布.结果表明:通过监测指标间的Pearson检验发现, 平谷区地下水电导率与ρ(Ca2+)(p=0.936)、总碱度与ρ(HCO₃2-)(p=0.981)、ρ(Mg2+)与总硬度(p=0.944)指标之间显著相关.地下水化学类型主要以HCO₃-Ca型为主,其次为HCO₃-Mg型.NH₄+、SO₄2-、Cd、Fe(Ⅱ)、NO₂指标空间分布离散性和差异性较大,存在局部富集现象.通过因子分析法筛选出影响平谷区地下水水质的8个公因子,首要影响因子为溶滤-富集作用(贡献率为22.398%),次要影响因子为农业、养殖业和填埋场等人为活动作用(贡献率为16.533%),雨水下渗作用(贡献率为8.035%)、工业源人为活动(贡献率为7.466%)对地下水也有一定影响.通过比较各指标的SOM(Self-Organizing Map,自组织映射)特征图像和监测井映射特征图像,发现NH₄+受山前地带林业、种植业和平原地带农业、养殖业的双重影响,Na+、Mn受平原地带人为活动的影响;同时,NH₄+、NO₃-、NO₂三者之间及Fe(Ⅱ)与Fe(Ⅲ)之间来源不同,Cd、Al、氰化物三者具有同一来源.研究显示,PCA-SOM(PCA与SOM相结合)可以对地下水化学组分来源进行定性识别与定量分析.      

三江源植被碳利用率动态变化及其对气候响应

本文基于MODIS GPP/NPP数据估算了三江源植被碳利用率（CUE）,结合气象数据和高程数据采用一元线性回归和相关分析法,探讨了2001~2017年三江源植被CUE的时空变化特征及植被CUE对气温、降水量和蒸散量变化的响应.结果表明：（1）三江源植被CUE年内3~10月表现为先增加后降低的变化趋势,其中6月植被CUE最高.（2）三江源年植被碳利用率位于0.73~1,平均水平为0.85;植被CUE空间上呈现北高南低,西高东低的分布特征.（3）整体上,三江源4~10月植被碳利用率与同期气温、降水量和蒸散量分别呈现正相关、负相关和负相关关系,降水量是影响三江源植被CUE变化的主要影响因素,气温为次要因素,蒸散量影响程度最小.