HEAVY RAINFALL DISTRIBUTIONS BY SEASON IN LOUISIANA: SYNOPTIC INTERPRETATIONS AND QUANTILE ESTIMATES1

ABSTRACT: In most studies, quantile estimates of extreme 24-hour rainfall are given in annual probabilities. The probability of experiencing an excessive storm event, however, differs throughout the year. As a result, this paper explored the differences between heavy rainfall distributions by season in Louisiana. It was concluded by using the Kruskal-Wallis and Mann-Whitney tests that the distribution of heavy rainfall events differs significantly between particular seasons at the sites near the Gulf Coast. Furthermore, seasonal frequency curves varied dramatically at the four sites examined. Mixed distributions within these data were not found to be problematic, but the mechanisms that produced the events were found to change seasonally. Extreme heavy rainfall events in winter and spring were primarily generated by frontal weather systems, while summer and fall events had high proportions of events produced by tropical disturbances and airmass (free-convective) conditions.     

SIMULATION OF TEMPORAL CHANGES IN RAINFALL-RUNOFF CHARACTERISTICS,COON CREEK BASIN,WISCONSIN1

ABSTRACT: Streamflow for 67 years was simulated for Coon Creek at Coon Valley, Wisconsin, for three conditions in the drainage basin: (1) conditions in the 1930s; (2) conditions in the 1970s, excluding flood-detention reservoirs; and (3) conditions in the 1970s, including flood-detention reservoirs. These simulations showed that the changes in agricultural practices over 40 years (1940–80) reduced the 100-year flood by 53 percent (from 38,900 to 18,300 cubic feet per second). The flood-detention reservoirs reduced the 100-year flood by an additional 17 percent (to 15,100 cubic feet per second). The simulation was accomplished by calibrating a precipitation-runoff model to observed rainfall and runoff during two separate periods (1934–40 and 1978–81). Comparisons of model simulations showed that differences between the model calibrations for the two periods were statistically significant at the 95 percent confidence level.     

UNCERTAINTY IN ESTIMATING BANKFULL CONDITIONS1

ABSTRACT: Bankfull depth and discharge are basic input parameters to stream planform, stream restoration, and highway crossing designs, as well as to the development of hydraulic geometry relationships and the classification of streams. Unfortunately, there are a wide variety of definitions for bankfull that provide a range of values, and the actual selection of bankfull is subjective. In this paper, the relative uncertainty in determining the bankfull depth and discharge is quantified, first by examining the variability in the estimates of bankfull and second by using fuzzy numbers to describe bankfull depth. Fuzzy numbers are used to incorporate uncertainty due to vagueness in the definition of bankfull and subjectivity in the selection of bankfull. Examples are provided that demonstrate the use of a fuzzy bankfull depth in sediment trans. port and in stream classification. Using fuzzy numbers to describe bankfull depth rather than a deterministic value allows the engineer to base designs and decisions on a range of possible values and associated degrees of belief that the bankfull depths take on each value in that range.     

OPTIMIZATION MODELING OF A NEW FACILITY FOR THE CALIFORNIA STATE WATER PROJECT1

ABSTRACT: A non-linear optimization model is applied to the California State Water Project (SWP) and portions of the Central Valley Project (CVP). The model accounts for the major hydrologic, regulatory, and operational features of both projects. The model maximizes long-term SWP yields over a 70-year period, using a quarterly time step. The potential for increased yield associated with a proposed facility improvement is evaluated with the model. The proposed facility is an extension of the Folsom-South Canal, which would allow water to be conveyed from the American River below Folsom Reservoir into New Melones Reservoir on the Stanislaus River or into the California Aqueduct. Model results indicate that extension of the Folsom-South Canal has the potential to increase SWP yields by 13 percent.     

WASTE LOADINGS FROM A FRESHWATER ATLANTIC SALMON FARM IN SCOTLAND1

ABSTRACT: Recent studies suggest that waste generation from the freshwater phase of Atlantic salmon (Salmo salar L.) production varies considerably on an annual basis. A fish farm on the West Coast of Scotland was visited regularly during a two-year period to determine inflow and outflow water quality. Waste output budgets of suspended solids (SS), biochemical oxygen demand (BOD), total nitrogen (TN), total phosphorus (TP), total ammonia nitrogen (TAN = NH₃+NH₄⁺), dissolved reactive phosphorus (DRP) and total phosphorus (TP) were produced. The annual waste loadings obtained were 71 kg TN t fish^?1 yr^?1 (one year of data only), 10.9–11.1 kg TP t fish^?1 yr^?1, 1.2–2.1 kg DRP t fish^?1 yr^?1, 422–485 kg BOD₅ t fish^?1 yr^?1, 327–337 kg SS t fish^?1 yr^?1, and 30–35 kg TAN-N t fish^?1 yr^?1. Simple linear regression models relating waste parameter production to water temperature and feeding regime were developed. When compared to existing data for other salmonid production systems, greater ranges of daily waste loadings were observed. Wide variations in concentrations of these parameters during a daily cycle were also observed, suggesting that mass balance estimates of waste production will provide more robust estimates of waste output than frequent monitoring of outflow water quality.     

Starch- polyvinyl alcohol crosslinked film— performance and biodegradation

Starch-PVOH cast films were prepared with and without crosslinking agent (hexamethoxymethylmelamine) in the absence of plasticizer. Moisture absorption in films without crosslinking agent at a low relative humidity was similar to that of PVOH and increased as the relative humidity increased. Films with crosslinking agent showed moisture absorption linearly proportional to the relative humidity. Significant improvement in resistance to water disintegration for crosslinked starch-PVOH films was observed. While the tensile strength decreased with increased relative humidity, crosslinking significantly improved the tensile strength. Increased PVOH content improved elongation of films even when the relative humidity was 80% or higher. Biodegradation studies revealed that the degradation rate was negatively correlated with the PVOH content in films and crosslinking generated more converged degradation curves. Names are necessary to report factually on available data; however, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the product to the exclusion of others that may also be suitable.     

Laboratory scale studies on gaseous emissions generated by the incineration of an artificial automotive shredder residue presenting a critical composition

Car manufacturers must eliminate automotive shredder residues (ASR). Two ways of incineration are of interest: at 850°C in municipal waste incinerators or at higher temperatures, above 1100°C in cement plants. These processes reduce the mass and the volume of waste to be disposed of in landfills and energy recovery might be possible. Regulations govern the emission of gaseous effluents to control environmental risk. To determine gaseous effluents from a pilot sacle or an industrial incineration plant, an artificial ASR was made by mixing three representative organic polymers present in the real ASR, namely polyvinylchloride, polyurethane and rubber. This mixture was incinerated at 850 and 1100°C in laboratory experiments and the analyses of the principal gaseous effluents such as carbon oxides, nitrogen oxides, volatile organic compounds, hydrochloric and hydrocyanic acids and sulphur compounds are presented and discussed. Lastly, in order to simulate artificial ASR behaviour, the composition of the combustion gases at equilibrium was calculated using a Gibbs energy minimisation code.     

Groundwater Remediation and Aquifer Clean-Up: A Case Study

Groundwater was being remediated with pump and treat technology at a facility where the groundwater was contaminated with commonly used degreaser solvents. Hydraulic conductivity of the heterogeneous residuum was beneficiated by applying pneumatic fracturing technology. The remedial system was controlled and monitored by a sophisticated remote telemetry system. A case history follows.     

Remediation of acid mine drainage leachate by a physicochemical and biological treatment‐train approach

Biological and physicochemical approaches were utilized in a treatment train for acid mine dis charge (AMD) waters. Anaerobic bioreactors, chemical precipitation reactors, and biopolymer chelation reactors, operated in static, semicontinuous, and continuous flow modes, removed significant quantities of metals and sulfates associated with AMD water. Static tests indicated accept able copper removal via precipitation by generation of hydrogen sulfide in anaerobic reactors. However, low pH affected the biopolymer coating in the chelation reactor, resulting in loss of bed surface. Corrections of AMD to pH > 7 resulted in some metal precipitationprior to biopolymer treatment. A series of static semicontinuous tests at pH 5.0 provided improved metal and sulfate removal. Copper (Cu⁺) was reduced to trace concentrations, while manganese (Mn⁺), although reduced, proved to be the most recalcitrant of the metals. © 2006 Wiley Periodicals, Inc.