TiO2-rGO制备及其对亚甲基蓝溶液的降解

本实验用改进的Hummers法制备氧化石墨烯(GO),通过溶胶-凝胶法制备得到TiO2-石墨烯复合材料(TiO2-rGO),研究了不同制备条件对复合材料光催化性能的影响。采用X射线衍射(XRD),拉曼光谱(Raman),比表面积(BET),扫描电镜(SEM),透射电镜(TEM)、紫外-可见(UV-Vis)吸收光谱和荧光光谱(PL)等测试手段对复合材料进行表征。结果表明,TiO2-rGO复合材料中的TiO2为锐钛相,且能均匀附着在石墨烯片层上,呈现层状堆积结构;与纯TiO2相比,复合材料具有较大的比表面积和更高的可见光响应。研究了该复合催化剂在紫外光下对亚甲基蓝以降解效果。当焙烧温度为450℃、TiO2/GO质量比为125:1时,制备得到的TiO2-rGO具有最优的光催化效果。     

硫酸体系退镀回收ABS电镀件的工艺

利用H2O2-H2SO4体系作为退镀液,考察硫酸浓度、双氧水浓度、液固比和反应时间等因素对丙烯腈-丁二烯-苯乙烯聚合物(ABS)电镀件退镀效果的影响。寻求使ABS塑料和金属完全分离的最优工艺条件。在硫酸质量分数为15%,双氧水质量分数7%,液固比为10,反应时间为50 min时,退镀率可达到99.45%。最后得到硫酸铜、硫酸镍和硫酸的混合溶液,经过探讨选择电积脱铜-蒸发结晶的方式得到阴极铜、海绵铜、黑铜、粗制硫酸镍、黑酸等。     

曝气条件对浸没式膜生物反应器内流场的影响

为深入研究流场动力学特性对浸没式膜生物反应器系统内膜面污染的控制,应用fluent软件对浸没式膜生物反应器内气液两相流动进行了三维数值模拟研究。采用标准k-ε湍流模型和欧拉多相流模型,考察了改变曝气条件对膜面气液速度场及气含率分布的影响。模拟结果表明,在相同曝气强度下,1 mm曝气孔径下膜面气液两相的速度增加较孔径2 mm、3 mm的快;曝气孔径为1 mm时,膜面的液相速度随着曝气强度的增加逐渐增大;曝气孔径为1 mm时,曝气量为5.5 m3/h所形成的漩涡区较大,膜面气含率值较高且分布较均匀,气液两相接触面积较大,膜面冲刷效果较好;模拟观察到反应器底部靠近壁面局部气含率较低,不利于活性污泥中微生物的生长,需要进一步优化曝气和反应器结构。     

MnO2/Al2O3吸附草甘膦及微波紫外耦合降解再生工艺

以掺混煅烧法制备MnO2/Al2O3,并对草甘膦进行吸附,将吸附态草甘膦置于微波紫外耦合系统中进行降解和再生。研究并给出了MnO2/Al2O3的最佳制备条件、最佳吸附条件和微波紫外耦合降解再生的最佳工艺参数。MnO2/Al2O3最佳制备条件为MnO2质量分数15%,煅烧温度500℃,煅烧时间2 h。在常温下,MnO2/Al2O3对草甘膦的最大吸附量为75 mg/g。微波紫外耦合系统最佳工艺参数为功率500 W,时间25 min,空气量0.06 m3/h。在此操作条件下,MnO2/Al2O3的再生率达到85%,并且可以多次再生利用,草甘膦最终降解产物为二氧化碳、氮氧化物、磷酸和水,矿化率为65%。     

Fe3+和Cu2+对饮用水氯消毒副产物三卤甲烷形成的影响

为了研究水中存在Br-的情况下,Fe3+和Cu2+对三卤甲烷(THMs)的生成及CHCl3、CHBrCl2、CHBr2Cl、CHBr3 4种消毒副产物相对分布的影响,以腐殖酸模拟氯消毒过程中的前体物进行实验。结果表明,在pH为6、7和9 3种条件下,Fe3+抑制了THMs的生成,pH=6时只有CHCl3生成量随着Fe3+浓度的增加逐渐减少,其余3种消毒副产物均在增加,pH=7时4种消毒副产物浓度均减小并在Fe3+浓度为2 mg/L时生成量最低,pH=9时的生成趋势与pH=6时类似。Cu2+能促进THMs的生成,在pH为6、7和9时,当加入0.5 mg/L Cu2+时,THMs总量分别增加了16.7%、22.6%和2.5%,随着pH增加,THMs总量增加。在3种pH环境中,Cu2+对THMs生成的影响大于Fe3+,在偏酸性环境中,Fe3+影响THMs生成,产生的致癌风险高,当金属离子浓度为2.5 mg/L时,致癌风险相差最高为15%,在中性和偏碱性环境中,Cu2+影响THMs生成,产生的致癌风险高。     

密相塔半干法烟气脱硫塔内加湿降温及其对脱硫效率的影响

为了实现密相塔半干法脱硫工艺的精确加湿进一步提高系统脱硫效率,利用推导出的传热传质计算方法,得到烟气温度降低和加水量的关系.结合3组密相塔半干法工程实际数据,发现理论计算值和实测值误差区间仅为2.9%~5.4%.通过选取河北某钢厂210 m2烧结烟气密相塔半干法脱硫项目实际在线检测数据,发现循环脱硫灰含湿量为3%的系统脱硫效率整体高于含湿量为5%和4%的样品,最大值达93.56%.通过粒度分析、扫描电镜、X射线衍射及差热-热重对2种不同含湿量的循环脱硫灰进行表征,结果表明,含湿量为3%的循环脱硫灰较含湿量为5%的样品粒径小、比表面积大,无团聚现象,物相分析还证实相对于含湿量为5%样品,其Ca(OH)2和结晶水含量少,几乎都是CaSO4和CaSO3干态物质,因此脱硫反应进行彻底,脱硫效率较高.     

Effect of temperature and particle size on the thermal desorption of PCBs from contaminated soil

Thermal desorption is widely used for remediation of soil contaminated with volatiles, such as solvents and distillates. In this study, a soil contaminated with semivolatile polychlorinated biphenyls (PCBs) was sampled at an interim storage point for waste PCB transformers and heated to temperatures from 300 to 600 °C in a flow of nitrogen to investigate the effect of temperature and particle size on thermal desorption. Two size fractions were tested: coarse soil of 420–841 μm and fine soil with particles <250 μm. A PCB removal efficiency of 98.0 % was attained after 1 h of thermal treatment at 600 °C. The residual amount of PCBs in this soil decreased with rising thermal treatment temperature while the amount transferred to the gas phase increased up to 550 °C; at 600 °C, destruction of PCBs became more obvious. At low temperature, the thermally treated soil still had a similar PCB homologue distribution as raw soil, indicating thermal desorption as a main mechanism in removal. Dechlorination and decomposition increasingly occurred at high temperature, since shifts in average chlorination level were observed, from 3.34 in the raw soil to 2.75 in soil treated at 600 °C. Fine soil particles showed higher removal efficiency and destruction efficiency than coarse particles, suggesting that desorption from coarse particles is influenced by mass transfer.     

宝钢焦化废水处理脱氮研究与实践

针对上海提高新排放标准中总氮(TN)≤35 mg/L的要求,对焦化废水进行了脱氮研究。选取现场缺氧-好氧-好氧(A-O-O)工艺中前两段的A-O生化沉淀池1出水,在SBR内进行反硝化脱氮实验,考察葡萄糖、葡萄糖+乙酸钠、甲醇和甲醇+乙酸钠单一或复合碳源及投加反硝化菌种对脱氮的影响,确定最佳碳源为甲醇+乙酸钠,最佳反硝化水力停留时间为16 h。当反硝化菌液投加浓度为1 mg/L时,SBR出水TN满足达标排放要求。结合实验结果对宝钢焦化废水原有AO-O工艺改造升级为A-O-A-O二段脱氮工艺,并对生化出水实施进一步的物化混凝处理。改造后,工艺长期运行稳定,最终出水完全达到上海市污水综合排放标准(DB 31/199-2009)TN≤35 mg/L的要求,并满足氰化物、氟化物以及COD的排放要求。     

Some technical issues in managing PCBs

Polychlorinated biphenyls (PCBs) were important industrial chemicals featuring high thermal and chemical stability and low flammability. They were widely used as dielectric and thermal fluid in closed electro-technical applications (transformers, capacitors…) and also in numerous dispersive uses, ranking from auto-copying paper to sealant or coatings. During the 1960s, severe environmental consequences started becoming apparent. The stability of PCBs contributed to their persistence in the environment, their lipophilic character to bio-magnification. Fish-eating species seemed threatened in their existence. In Japan and in Taiwan, thousands of people consumed PCB-contaminated oil. The production of PCBs stopped completely during the 1980s. Usage could continue in closed applications only. In this paper, particular attention is given to two issues: the cleaning of PCB electric transformers and the potential impact of PCB-containing building materials. Other contributions will cover the management and treatment of PCB-contaminated soil, sludge or fly ash. The complete survey is being prepared by request of the Knowledge Center for Engineers and Professionals.     

基于改性凹凸棒土的强化混凝处理高藻低浊原水工艺

针对水厂低浊高藻水的处理难题,研究了改性凹凸棒土(改性凹土)联合聚合氯化铝(PAC)强化混凝的除藻除浊效果。设计实验原水条件为叶绿素a(chl-a)浓度为98.58~110.35μg/L,浊度(5.6±0.5)NTU。考察了PAC和改性凹土的复配投加量、混凝沉淀时间、pH、投加顺序、搅拌速率等工艺参数对Chl-a和浊度耦合去除效果的影响。结果表明,"PAC+改性凹土"对Chl-a和浊度的去除效果明显优于单投PAC的效果。当PAC投药量12 mg/L,改性凹土投药量10 mg/L,沉淀时间20 min时,对Chl-a和浊度的去除率可分别达到92.5%和89.2%,可至少减少40%的PAC投量,且形成的矾花密实,沉降速度快,去除效率高。最适pH范围为7~8。投加顺序应为先投加改性凹土,混合搅拌转数宜慢速,可控制为50 r/min。