Determination of selected fate and aquatic toxicity characteristics of acrylic acid and a series of acrylic esters

Acrylic acid, methyl acrylate, ethyl acrylate, and butyl acrylate are commercially important and widely used materials. This paper reports the results of a series of fate and aquatic toxicity studies. The mobility in soil of acrylic acid and its esters ranged from 'medium' to 'very high'. Calculated bioconcentration factors ranged from 1 to 37, suggesting a low bioconcentration potential. Acrylic acid and methyl acrylate showed limited biodegradability in the five day biochemical oxygen demand (BOD5) test, while ethyl acrylate and butyl acrylate were degraded easily (77% and 56%, respectively). Using the OECD method 301D 28-d closed bottle test, degradability for acrylic acid was 81% at 28 days, while the acrylic esters ranged from 57% to 60%. Acrylic acid degraded rapidly to carbon dioxide in soil (t1/2 < 1 day). Toxicity tests were conducted using freshwater and marine fish, invertebrates, and algae. Acrylic acid effect concentrations for fish and invertebrates ranged from 27 to 236 mg/l. Effect concentrations (LC50 or EC50) for fish and invertebrates using methyl acrylate, ethyl acrylate, and butyl acrylate ranged from 1.1 to 8.2 mg/l. The chronic MATC for acrylic acid with Daphnia magna was 27 mg/l based on length and young produced per adult reproduction day and for ethyl acrylate was 0.29 mg/l based on both the reproductive and growth endpoints. Overall these studies show that acrylic acid and the acrylic esters studied can rapidly biodegrade, have a low potential for persistence or bioaccumulation in the environment, and have low to moderate toxicity.     

Nitrogen oxides from waste incineration: control by selective non-catalytic reduction

An experimental study of the selective non-catalytic reduction (SNCR) process was carried out to determine the efficiency of NOx removal and NH3 mass balance, the NOx reducing reagent used. Experimental tests were conducted on a full-scale SNCR system installed in a hospital waste incineration plant. Anhydrous NH3 was injected at the boiler entrance for NOx removal. Ammonia was analyzed after each flue-gas treatment unit in order to establish its mass balance and NH3 slip in the stack gas was monitored as well. The effective fraction of NH3 for the thermal NOx reduction was calculated from measured values of injected and residual NH3. Results show that a NOx reduction efficiency in the range of 46.7-76.7% is possible at a NH3/NO molar ratio of 0.9-1.5. The fraction of NH3 used in NOx removal was found to decrease with rising NH3/NO molar ratio. The NH3 slip in the stack gas was very low, below permitted limits, even at the higher NH3 dosages used. No direct correlation was found between the NH3/NO molar ratio and the NH3 slip in the stack gas since the major part of the residual NH3 was converted into ammonium salts in the dry scrubbing reactor and subsequently collected in the fabric filter. Moreover, another fraction of NH3 was dissolved in the scrubbing liquor.     

Mechanisms of lead, copper, and zinc retention by phosphate rock

The solid-liquid interface reaction between phosphate rock (PR) and metals (Pb, Cu, and Zn) was studied. Phosphate rock has the highest affinity for Pb, followed by Cu and Zn, with sorption capacities of 138, 114, and 83.2 mmol/kg PR, respectively. In the Pb-Cu-Zn ternary system, competitive metal sorption occurred with sorption capacity reduction of 15.2%, 48.3%, and 75.6% for Pb, Cu, and Zn, respectively compared to the mono-metal systems. A fractional factorial design showed the interfering effect in the order of Pb>Cu>Zn. Desorption of Cu and Zn was sensitive to pH change, increasing with pH decline, whereas Pb desorption was decreased with a strongly acidic TCLP extracting solution (pH = 2.93). The greatest stability of Pb retention by PR can be attributed to the formation of insoluble fluoropyromorphite [Pb(10)(PO(4))(6)F(2)], which was primarily responsible for Pb immobilization (up to 78.3%), with less contribution from the surface adsorption or complexation (21.7%), compared to 74.5% for Cu and 95.7% for Zn. Solution pH reduction during metal retention and flow calorimetry analysis both supported the hypothesis of retention of Pb, Cu, and Zn by surface adsorption or complexation. Flow calorimetry indicated that Pb and Cu adsorption onto PR was exothermic, while Zn sorption was endothermic. Our research demonstrated that PR can effectively remove Pb from solutions, even in the presence of other heavy metals (e.g. Cu, Zn).     

Co-injection of air and steam for the prevention of the downward migration of DNAPLs during steam enhanced extraction: an experimental evaluation of optimum injection ratio predictions

When steam is injected into soil containing a dense volatile non-aqueous phase liquid contaminant, the DNAPL vaporized within the heated soil region condenses and accumulates ahead of the steam condensation front. If enough DNAPL accumulates, gravitational forces can overcome trapping forces allowing the liquid contaminant to flow downward. By injecting air with steam, a portion of the DNAPL vapor remains suspended in equilibrium with the air, decreasing liquid contaminant accumulation ahead of the steam condensation front, and thus reducing the possibility of downward migration. In a previous work, a theoretical model was developed to predict the optimum injection ratio of air to steam that would eliminate accumulation of DNAPL ahead of the temperature front and thus minimize the potential for downward migration. In this work, the theoretical model is summarized, and an experiment is presented in order to evaluate the optimum injection ratio prediction. In the experiment, a two-dimensional water saturated sand pack is contaminated with a known mass of TCE (DNAPL). The system is then remediated by co-injecting air and steam at the predicted optimum injection ratio, calculated based on the average contaminant soil concentration in the sand pack. Results for the co-injection of air and steam are compared to results for the injection of pure steam or pure air. Injection at the predicted optimum injection ratio for a volumetric average NAPL saturation, reduced accumulation of the contaminant ahead of the condensation front by over 90%, as compared to steam injection alone. This indicates that the optimum injection ratio prediction is a valuable tool for limiting the spreading of DNAPL during steam-enhanced extraction. Injection at the optimum injection ratio resulted in earlier recovery of contaminant than for steam injection alone. Co-injection of steam and air is also shown to result in much higher recovery rates than air injection alone.     

Effect of surfactants at low concentrations on the sorption of atrazine by natural sediment.

A series of experiments were carried out to determine the effect of surfactants at low concentrations on the sorption of atrazine by natural sediments. With surfactant concentrations ranging from 0 to 20 mg/ L, anionic and cationic surfactants appreciably reduce the adsorption of atrazine, while nonionic surfactant decreases the adsorption of atrazine at concentrations equal to or less than 1 mg/L and increases adsorption at higher concentrations. Desorption of atrazine in the presence of different sodium dodecylbenzene sulfonate (SDBS) concentrations shows that a portion of the bound pesticide resists desorption in the SDBS free system. However, the addition of SDBS accelerates the desorption of atrazine. Furthermore, the nature of sediment and the contacting sequence of SDBS, at 10 mg/L, with the sediment, also influence the adsorption of atrazine. The conclusions in this study could be explained partially by the effect of the type and concentration of surfactants and the characteristics of sediments.     

Comparative study of extraction methods for the determination of PAHs from contaminated soils and sediments

The following four methods were compared on the extraction efficiency of 16 EPA (US Environmental Protection Agency) polycyclic aromatic hydrocarbons (PAHs): German method of the Verband Deutscher Landwirtschaftlicher Untersuchungs und Forschungsanstalten (VDLUFA), two methods of the International Organization for Standardization using shaking (ISO A) and Soxhlet extraction (ISO B) and an ultrasonic method. Recovery rates of 16 PAHs were determined in two soils. Extraction efficiency was evaluated in five soils and three sediments. Effect of drying soils and sediments on extraction efficiency was tested using the VDLUFA and the ultrasonic methods. Our study shows that the number of aromatic rings, rather than extraction procedures, significantly influenced recovery rates of individual PAHs. No significant differences in extraction efficiency of the four methods were observed for less polluted samples. For highly polluted soils, extraction efficiency decreased in the following order: VDLUFA method > ISO A > ultrasonic method > ISO B. Influence of soil moisture on extraction efficiency depended to some extent on both solvent used and content of PAHs in samples. A mixture of dichloromethane/acetone (5:1) is recommended for PAH extraction from moist samples when the ultrasonic method is used.     

Redox-active ligands in artificial photosynthesis: a review

Environmental Chemistry Letters - Given the rising socioeconomic issues of fossil fuels, efficient artificial photosynthesis would be an important milestone toward a sustainable world. A key step...     

Biodegradation of phthalate esters by two bacteria strains

In this study two aerobic phthalic acid ester (PAE) degrading bacteria strains, DK4 and O18, were isolated from river sediment and petrochemical sludge, respectively. The two strains were found to rapidly degrade PAE with shorter alkyl-chains such diethyl phthalate (DEP), dipropyl phthalate (DPrP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP) and diphenyl phthalate (DPP) are very easily biodegraded, while PAE with longer alkyl-chains such as dicyclohexyl phthalate (DCP) and dihexyl phthalate (DHP) and di-(2-ethylhexyl) phthalate (DEHP) are poorly degraded. The degradation rates of the eight PAEs were higher for strain DK4 than for strain O18. In the simultaneous presence of strains DK4 and O18, the degradation rates of the eight PAEs examined were enhanced. When the eight PAEs were present simultaneously, degradation rates were also enhanced. We also found that PAE degradation was delayed by the addition of nonylphenol or selected polycyclic aromatic hydrocarbons (PAHs) at a concentration of 1 microg/g in the sediment. The bacteria strains isolated, DK4 and O18, were identified as Sphigomonas sp. and Corynebacterium sp., respectively.