Studies on degradation of glyphosate by several oxidative chemical processes: Ozonation,photolysis and heterogeneous photocatalysis

Several different Advanced Oxidation Processes (AOPs) including ozonation at pH 6.5 and 10, photolysis and heterogeneous photocatalysis using TiO₂ as semiconductor and dissolved oxygen as electron acceptor were applied to study the degradation of glyphosate (N-phosphonomethyl glycine) in water. The degree of glyphosate degradation, the reactions kinetic and the formation of the major metabolite, aminomethyl phosphonic acid (AMPA), were evaluated. Ozonation at pH 10 resulted in the maximum mineralization of glyphosate. It was observed that under the experimental conditions used in this study the degradation of glyphosate followed the first-order kinetics. The half-life obtained for glyphosate degradation in the O₃/pH 10 process was 1.8 minutes.     

An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE)

The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile–butadiene–styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive.     

Antimony leaching in plastics from waste electrical and electronic equipment (WEEE) with various acids and gamma irradiation

There has been a recent interest in antimony since the availability in readily mined areas is decreasing compared to the amounts used. It is important in many applications such as flame retardants and in the production of polyester, which can trigger an investigation of the leachability of antimony from plastics using different acids. In this paper, different types of acids are tested for their ability to leach antimony from a discarded computer housing, made of poly(acrylonitrile butadiene styrene), which is a common plastic type used in electrical and electronic equipment. The acid solutions included sodium hydrogen tartrate (0.5 M) dissolved in either dimethyl sulfoxide or water (at ca. 23 °C and heated to ca. 105 °C). The metal content after leaching was determined by inductively coupled plasma optical emission spectroscopy. The most efficient leaching medium was the heated solution of sodium hydrogen tartrate in dimethyl sulfoxide, which leached almost half of the antimony from the poly(acrylonitrile butadiene styrene). Gamma irradiation, which is proposed to improve the mechanical properties in plastics, was used here to investigate the influence of antimony leaching ability. No significant change in the amount of leached antimony could be observed.     

Design and field application of an automated cartridge sampler for VOC concentration and flux measurements

One of the major limitations in advancing the understanding of tropospheric ozone and aerosol generation and developing strategies for their control is the technical ability to accurately measure volatile organic compounds (VOCs). This paper describes the design of a constant flow VOC sampler. The versatile sampler can be used for fully automated concentration and flux measurements of VOCs. The sampler incorporates a microprocessor control unit and provides highly accurate mass flow control and significant ease of operation. Sampling sequences can be programmed directly or by remote control through a PC. All important operational parameters necessary for a complete sampling audit trail are logged. Compact weatherproof housings and low power consumption allow operation at remote sites and locations which are sensitive to disturbances or have restricted access. Inner wetted surfaces of the sampler are constructed from non-contaminating materials that do not sorb or emit VOC, and thus permit the collection of representative samples even in environments with very low VOC concentrations. The cartridge magazine provides a maximum of 20 sequential cartridge samples, which allows for long-term air quality assessments. In the dual channel mode, two samples can be collected simultaneously through two independent sample loops, providing ten sequential sample pairs. This design allows the parallel collection of (a) quality assurance backup samples, (b) samples on two different types of cartridges/sorbents to allow a variety of analyses, or (c) differential samples for flux measurements using enclosure, aerodynamic profile, or relaxed eddy accumulation (REA) methods. Field applications including airplane profile measurements above a tropical rainforest area, as well as gradient and REA measurements over a mid-latitude mixed forest stand are described, and demonstrate the validity and flexibility of the system. In particular, the application of the VOC sampler as an integrated part of a REA system is emphasized.     

Bioethanol-gasoline fuel blends: exhaust emissions and morphological characterization of particulate from a moped engine

This study was aimed at evaluating the effects of gasoline-ethanol blends on the exhaust emissions in a catalyst-equipped four-stroke moped engine. The ethanol was blended with unleaded gasoline in at percentages (10, 15, and 20% v/v). The regulated pollutants and the particulate matter emissions were evaluated over the European ECE R47 driving cycle on the chassis dynamometer bench. Particulate matter was characterized in terms of total mass collected on filters and total number ofparticles in the range 7 nm-10 microm measured by electrical low-pressure impactor (ELPI). In addition, particle-phase polycyclic aromatic hydrocarbons (PAHs) emissions were evaluated to assess the health impact of the emitted particulate. Finally, an accurate morphological analysis was performed on the particulate by high-resolution transmission electron microscope (TEM) equipped with a digital image-processing/data-acquisition system. In general, CO emission reductions of 60-70% were obtained with 15 and 20% v/v ethanol blends, while the ethanol use did not reduce hydrocarbon (HC) and NOx emissions. No evident effect of ethanol on the particulate mass emissions and associated PAHs emissions was observed. Twenty-one PAHs were quantified in the particulate phase with emissions ranging from 26 to 35 microg/km and benzo[a]pyrene equivalent (BaPeq) emission factors from 2.2 to 4.1 microg/km. Both particulate matter and associated PAHs with higher carcinogenic risk were mainly emitted in the submicrometer size range (<0.1 microm). On the basis of the TEM observations, no relevant effect of the ethanol use on the particulate morphology was evidenced, showing aggregates composed ofprimary particles with mean diameters in the range 17.5-32.5 nm.     

Genetic diagnosis and clinical evaluation of severe fetal akinesia syndrome

Objective

In this retrospective study, we describe the clinical course, ultrasound findings and genetic investigations of fetuses affected by fetal akinesia.

Materials and Methods

We enrolled 22 eukaryotic fetuses of 18 families, diagnosed with fetal akinesia between 2008 and 2016 at the Department of Obstetrics and Feto-Maternal Medicine at the Medical University of Vienna. Routine genetic evaluation included karyotyping and chromosomal microarray analysis. Retrospectively, exome sequencing was performed in the index case of 11 families, if stored DNA was available. Confirmation analyses and genetic diagnosis of siblings were performed by using Sanger sequencing.

Results

Whole exome sequencing identified pathogenic variants of CNTN1, RYR1, NEB, GLDN, HRAS and TNNT3 in six cases of 11 families. In three of these families, the variants were confirmed in the respective sibling.

Conclusions

The present study demonstrates a high diagnostic yield of exome sequencing in fetuses affected by akinesia syndrome, especially if family history is positive. Still, in a large part the underlying genetic cause remained unknown, whereas precise clinical evaluation in combination with exome sequencing shows to be the best tool to find the disease causing variants.     

Inter-island movements of scalloped hammerhead sharks (Sphyrna lewini) and seasonal connectivity in a marine protected area of the eastern tropical Pacific

Marine top predators are common at offshore bathymetric features such as islands, atolls, and seamounts, where most pelagic reef fish reside, while certain sharks perform inter-island movements between these formations. Scalloped hammerhead sharks are known to school in great numbers at small islands and seamounts in the eastern tropical Pacific (ETP) and are very susceptible to fisheries while moving into the open sea. It is, therefore, essential to understand hammerhead inter-island movements and environmental effects to provide baseline information for their conservation and management within and beyond an insular marine protected area. Movements of scalloped hammerheads were analyzed in the Galapagos Marine Reserve (GMR) and ETP, and environmental factors were linked to their movements. Hammerheads were tagged (N = 134) with V16 coded pingers (July 2006 to July 2010) in the northern Galapagos and detected at listening stations around four islands in the GMR and two isolated islands in the ETP, 700 and 1,200 km away. Hammerheads formed daytime schools at specific locations, but dispersed at night. Overall, more daytime than nighttime detections were recorded at all receivers in the northern Galapagos Islands, and more detections in the up-current sides of these islands. Hammerheads remained more days at the northern islands during part of the warm season (December–February) compared to the cool; however, fewer individuals were present in March–June. Movement modes were diel island excursions (24-h cycles) in the northern Galapagos and inter-island in the GMR and ETP at different scales: (1) short back-and-forth (<50 km, SBF), <5 days cycles, (2) medium distance (50–300 km, MDT), 5–20 days, and (3) long distance (>300 km, LDT), 15–52 days. The high degree of inter-island connectivity of hammerheads within the northern GMR is striking compared to the almost nil movement to the central GMR. A seasonal migratory pattern to locations offshore is indicated by (1) fewer hammerheads observed in the northern GMR during part of the warm season (March–June) and (2) evidence of LDT movements from the northern GMR to other islands in the ETP. LDT movements of mature female hammerheads are possibly associated with pupping areas. Our results indicate that currents, season, and individual behavior mainly drive inter-island movements of hammerheads at small (SBF) and medium (MDT) scales. These findings have important implications for the management of a highly mobile and endangered top predator within a marine protected area and beyond.     

Use of statistical tools to evaluate the reductive dechlorination of high levels of TCE in microcosm studies

A large, multi-laboratory microcosm study was performed to select amendments for supporting reductive dechlorination of high levels of trichloroethylene (TCE) found at an industrial site in the United Kingdom (UK) containing dense non-aqueous phase liquid (DNAPL) TCE. The study was designed as a fractional factorial experiment involving 177 bottles distributed between four industrial laboratories and was used to assess the impact of six electron donors, bioaugmentation, addition of supplemental nutrients, and two TCE levels (0.57 and 1.90 mM or 75 and 250 mg/L in the aqueous phase) on TCE dechlorination. Performance was assessed based on the concentration changes of TCE and reductive dechlorination degradation products. The chemical data was evaluated using analysis of variance (ANOVA) and survival analysis techniques to determine both main effects and important interactions for all the experimental variables during the 203-day study. The statistically based design and analysis provided powerful tools that aided decision-making for field application of this technology. The analysis showed that emulsified vegetable oil (EVO), lactate, and methanol were the most effective electron donors, promoting rapid and complete dechlorination of TCE to ethene. Bioaugmentation and nutrient addition also had a statistically significant positive impact on TCE dechlorination. In addition, the microbial community was measured using phospholipid fatty acid analysis (PLFA) for quantification of total biomass and characterization of the community structure and quantitative polymerase chain reaction (qPCR) for enumeration of Dehalococcoides organisms (Dhc) and the vinyl chloride reductase (vcrA) gene. The highest increase in levels of total biomass and Dhc was observed in the EVO microcosms, which correlated well with the dechlorination results.     

Spectroscopic changes on fulvic acids from a kraft pulp mill effluent caused by sun irradiation

Large volumes of wastewater with a high organic load are generated by the pulp and paper industry that negatively affect the quality of receiving waters. The main waste products in the pulp mill effluents are lignin derived macromolecular compounds, which are similar to natural humic substances and very resistant to wastewater treatments. Fulvic acids (FA) represent the higher percentage of these humic substances and it was observed that solar irradiation modify their properties. Several analytic tools, namely, UV–Visible, molecular fluorescence and FTIR spectroscopies, were used to assess the effect of solar exposition on fulvic acids from a kraft pulp mill effluent. It may be concluded that sun irradiation may alter to a high extent the physicochemical properties of macromolecular organic matter, namely fulvic acids, released by kraft pulp mill effluents. After solar exposition, the aromaticity decreases, the aliphatic structures become more oxygenated, and the fulvic acids from the pulp mill effluent remaining in solution are more similar to aquatic fulvic acids from non polluted sites.     

Organic pollutants in compost and digestate. Part 2. Polychlorinated dibenzo-p-dioxins, and -furans, dioxin-like polychlorinated biphenyls, brominated flame retardants, perfluorinated alkyl substances, pesticides, and other compounds

Compost and digestate are important recycling fertilizers and have beneficial effects on soil parameters. However, they can contain significant amounts of organic pollutants. Here, the first comprehensive data set on dibenzo-p-dioxins and -furans (PCDD/F), dioxin-like polychlorinated biphenyls (DL-PCB), brominated flame retardants, perfluorinated alkyl substances (PFAS), pesticides, phthalates, nonylphenol and chlorinated paraffins (CP) in source-separated compost and digestate from Switzerland is presented (n = 3-18). The median summation 17PCDD/F and summation 12DL-PCB concentrations were at 3.2 ng I-TEQ kg(-1)dry weight (dw) and 3.0 ng WHO-TEQ kg(-1)dw, respectively. Brominated diphenyl ether 209 (BDE 209) accounted for 72% of the total polyBDE content (10 microg kg(-1)dw). Hexabromocyclododecane (HBCD) and tetrabromobisphenol A (TBBPA) levels were at 100 and 0.51 microg kg(-1)dw, respectively. PFAS were identified for the first time in compost and digestate (median concentration 6.3 microg kg(-1)dw, summation 21compounds). Out of 269 pesticides analysed, 30 fungicides, 14 herbicides, eight insecticides and one acaricide were detected. Di-(2-ethylhexyl)phthalate (DEHP) median concentration accounted for 280 microg kg(-1)dw and nonylphenol was below the detection limit of 1 mg kg(-1)dw. The sum of short and medium chain CP was between 90 and 390 microg kg(-1)dw. The concentrations observed were at or above the levels found in background soils, which are the main recipient of compost and digestate. Where actually applied, compost can contribute considerably to the total input of organic pollutants to the soil. However, on a total Swiss agricultural area base, inputs seem to be limited.