Aquatic biomonitoring of Giardia cysts and Cryptosporidium oocysts in peninsular Malaysia

An aquatic biomonitoring of Giardia cysts and Cryptosporidium oocysts in river water corresponding to five villages situated in three states in peninsular Malaysia was determined. There were 51.3 % (20/39) and 23.1 % (9/39) samples positive for Giardia and Cryptosporidium (oo)cysts, respectively. Overall mean concentration between villages for Giardia cysts ranged from 0.10 to 25.80 cysts/l whilst Cryptosporidium oocysts ranged from 0.10 to 0.90 oocysts/l. Detailed results of the river samples from five villages indicated that Kuala Pangsun 100 % (9/9), Kemensah 77.8 % (7/9), Pos Piah 33.3 % (3/9) and Paya Lebar 33.3 % (1/3) were contaminated with Giardia cysts whilst Cryptosporidium (oo)cysts were only detected in Kemensah (100 %; 9/9) and Kuala Pangsun (66.6 %; 6/9). However, the water samples from Bentong were all negative for these waterborne parasites. Samples were collected from lower point, midpoint and upper point. Midpoint refers to the section of the river where the studied communities are highly populated. Meanwhile, the position of the lower point is at least 2 km southward of the midpoint and upper point is at least 2 km northward of the midpoint. The highest mean concentration for (oo)cysts was found at the lower points [3.15?±?6.09 (oo)cysts/l], followed by midpoints [0.66?±?1.10 (oo)cysts/l] and upper points [0.66?±?0.92 (oo)cysts/l]. The mean concentration of Giardia cysts was highest at Kuala Pangsun (i.e. 5.97?±?7.0 cysts/l), followed by Kemensah (0.83?±?0.81 cysts/l), Pos Piah (0.20?±?0.35 cysts/l) and Paya Lebar (0.10?±?0.19 cysts/l). On the other hand, the mean concentration of Cryptosporidium oocysts was higher at Kemensah (0.31?±?0.19 cysts/l) compared to Kuala Pangsun (0.03?±?0.03cysts/l). All the physical and chemical parameters did not show significant correlation with both protozoa. In future, viability status and molecular characterisation of Giardia and Cryptosporidium should be applied to identify species and genotypes/subgenotypes for better understanding of the epidemiology of these waterborne parasites.     

初级基质对降解菌Pseudomonas putida共代谢苯扎贝特的影响

通过对3,5-二硝基水杨酸(DNS)法测定还原糖含量各影响因素的筛选,优化确定了显色时间8 min,稳定时间10 min,最佳波长490 nm下进行吸光度测定的检测方法;分析分别以葡萄糖和麦芽糖作为外加碳源时,降解菌Pseudomonas putida B-31的生长情况和共代谢降解典型药物苯扎贝特(BZF)的过程。结果表明,降解菌只有在外加碳源的条件下才可正常生长,而且其在葡萄糖环境中生长得更好;拟合得到的葡萄糖、麦芽糖和BZF代谢动力学结果显示,葡萄糖对BZF去除的促进作用更为明显,同时从葡萄糖培养基中降解菌所提取的酶比活力要高于麦芽糖培养基,分析原因可能是葡萄糖所诱导的降解菌关键酶活力更强,而且还可能会产生不同的蛋白质点位。     

Exposure to heavy metals in blood and risk perception of the population living in the vicinity of municipal waste incinerators in Korea

Background, aim, and scope

The purpose of this study was to monitor and present the heavy metal concentrations in the blood of residents of areas near municipal waste incinerators (MWIs), who are more prone to environmental pollution. We also sought to compare and analyze the residents?? perception of environmental pollution as one of the factors affecting heavy metal concentrations in the blood using a survey about the perceived damage caused by the facilities. Since heavy metal levels in the blood can be affected not only by local environmental pollution but also by personal and occupational factors, heavy metal levels in the blood need to be verified and consistently monitored.

Methods

Residents who live within 300?m of MWIs in Seoul are acknowledged to be under indirect influence according to the Waste Disposal Act. A survey was given to 841 residents living within 300?m of a MWI from 2006 to 2009. The concentrations of heavy metals (lead, cadmium, and mercury) in the blood were measured in the 841 surveyed residents and in 105 residents in reference areas. Additionally, the perception of the damage caused by municipal waste incinerators was investigated using scores from 1 to 5 on a Likert scale.

Results

The measurements of the heavy metal concentrations in the blood showed that the mean concentrations of lead, cadmium, and mercury were 43.1, 1.7, and 1.3?ug/L, respectively. The blood levels of lead and cadmium were slightly higher in the group of the subjects who had resided the longest near the municipal waste incinerators. When compared with the domestic investigation by the Ministry of Environment, the concentrations of lead and cadmium were a little higher, while that of mercury was a little lower. Overall, there was no significant difference in the distribution of heavy metal levels in the blood among age groups. Additionally, the investigation of the perceived damage from municipal waste incinerators showed that the subjects     

The relationship between flow and bacteria in streams

A method is proposed to relate the statistics of in-stream bacteria concentrations to the surface-runoff fraction of stream flow. The parameters of this relationship include the characteristic concentration of bacteria in surface runoff and the characteristic concentration of bacteria in the base flow, and these parameters can be derived from synoptic bacteria and flow measurements. The effectiveness of the proposed method is demonstrated at several U.S. locations for both Escherichia coli and fecal coliform bacteria. Application of the proposed method at a particular location showed that the method can be used to identify the most effective bacteria source controls and that conventional application of the load-duration curve might lead to erroneous identification of target sources.     

Nationwide monitoring of atmospheric PCDD/Fs and dioxin-like PCBs in South Korea

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) were measured in ambient air samples collected from different parts of South Korea in 2008, and the measured levels were used for assessing the spatial and temporal distribution of atmospheric PCDDFs and DL-PCBs in South Korea. The average concentrations of atmospheric PCDD/Fs and DL-PCBs among the 37 sites were 28 fg I-TEQ m⁻³ (ND ∼ 617) and 1 fg WHO-TEQ m⁻³ (ND ∼ 0.016). Elevated atmospheric levels of PCDD/Fs and DL-PCBs observed at residential/industrial sites and in the north-west of Korea, indicated a potential contribution and impacts of anthropogenic sources of PCDD/Fs and DL-PCBs. These levels were similar or lower than those previously reported in other ambient air surveys. Average concentrations of PCDD/Fs showed small seasonal variations (ANOVA analysis, p = 0.144). The highest concentrations of PCDD/Fs were observed during winter, followed by spring, autumn and summer. Atmospheric PCDD/Fs and DL-PCBs in South Korea rapidly decreased during the last 10 years (1998-2008), demonstrating the efficiency of stricter regulations and the application of best available technologies/best environmental practices at emission sources. Comparison of the congener profiles and principal component analysis showed that current atmospheric PCDD/Fs are mostly influenced by industrial sources and PCBs from old commercial PCB uses. Nationwide POPs monitoring will continue and allows an effective evaluation of the implementation of the Stockholm Convention on POPs.     

Removal of selected endocrine disrupting chemicals and personal care products in surface waters and secondary wastewater by ozonation

This study investigated the removal of parabens, N,N-diethyl-m-toluamide (DEET), and phthalates by ozonation. The second-order rate constants for the reaction between selected compounds with ozone at pH 7 were of (2.2 +/-0.2) X 10(6) to (2.9 +/-0.3) X 10(6) M 1/s for parabens, (2.1+/- 0.3) to (3.9 +/-0.5) M-1/s for phthalates, and (5.2 +/-0.3) M-1/s for DEET. The rate constants for the reaction between selected compounds with hydroxyl radical ranged from (2.49 +/-0.06) x 10(9) to (8.5 +/-0.2) x 10(9) M-1/s. Ozonation of selected compounds in secondary wastewater and surface waters revealed that ozone dose of 1 and 3 mg/L yielded greater than 99% depletion of parabens and greater than 92% DEET and phthalates, respectively. In addition, parabens were found to transform almost exclusively through the reaction with ozone, while DEET and phthalates were transformed almost entirely by hydroxyl radicals (.OH).     

Food waste treatment in a community center

For urban community composting centers, the proper selection and use of bulking agent is a key element in not only the cost but also the quality of the finished compost. Besides wood chips (WC) widely used as BA, readily usable cereal residue pellets (CRP) can provide biodegradable carbon and sufficient free air space (FAS) to produce stabilizing temperatures. The objective of the present project was to test at a community center, the effectiveness of CRP in composting food waste (FW). Two recipes were used (CRP with and without WC) to measure: FAS; temperature regimes, and; losses in mass, water, carbon and nitrogen. Both recipes were composted during three consecutive years using a 2 m³ commercial in-vessel composter operated in downtown Montreal (Canada). For all recipes, FAS exceeded 30% for moisture content below 60%, despite yearly variations in FW and BA physical properties. When properly managed by the center operator, both FW and CRP compost mixtures with and without WC developed within 3 days thermophilic temperatures exceeding 50 °C. The loss of total mass, water, carbon and nitrogen was quite variable for both recipes, ranging from 36% to 54%, 42% to 55%, 48% to 65%, and 4% to 55%, respectively. The highest loss in dry mass, water and C was obtained with FW and CRP without WC aerated to maintain mesophilic rather than thermophilic conditions. Although variable, lower nitrogen losses were obtained with CRP and WC as BA, compared to CRP alone, as also observed during previous laboratory trials. Therefore and as BA, CRP can be used alone but nitrogen losses will be minimized by adding WC. Compost stabilization depends on operator vigilance in terms of aeration. The measured fresh compost density of 530-600 kg/m³ indicates that the 2 m³ in-vessel composter can treat 6.5 tons of FW/year if operated during 7 months.     

Influence of peatland and land cover distribution on fire regimes in insular Southeast Asia

Anthropogenic biomass burning in insular Southeast Asia facilitates conversion and degradation of ecosystems and emits high amounts of carbon into the atmosphere. We analyzed the influence of peat soil and land cover distribution on the occurrence and characteristics of vegetation fires. Two years of satellite-based active fire detections over Peninsular Malaysia, Sumatra, Borneo and Java were examined together with land cover and peatland maps. Our results showed that fire occurrence nearly tripled (23,000 → 68,000) from a wet La Niña year (2008) to a drier El Niño year (2009). In both years, fires were concentrated in peatlands (in 2009 41% of fires vs. 10% of land area), and the majority of large-scale burning took place in peatlands. Variation in peatland land cover within the study area was noticed to create remarkable different fire regimes. Biomass burning in the intensely managed Sumatran peatlands was characterized by large-scale land clearance fires that took place annually to varying extent. The largely unmanaged degraded peatland ecosystems of Borneo, on the other hand, experienced very little fire activity in a wet year but were ravaged by large-scale wildfires when El Niño conditions arose. We conclude that fire regime characteristics in insular Southeast Asia are strongly connected to occurrence of peat soil and land management status. This leads to high variation of fire activity within this region both annually (depending on weather patters) and over longer time range (depending on land cover/management issues) and greatly complicates estimation of the effects of fires.     

Effects of post-sampling conditions on ambient carbon aerosol filter measurements

Ambient carbonaceous material collected on quartz filters is prone to measurement artifacts due to material gained or lost during post-sampling field latency, shipping, and storage. In seventeen sampling events over a one year period, ambient PM_2.5 aerosols were collected on quartz filters (without denuders) and subjected to various filter treatments to assess the potential for and extent of artifacts. The filter treatments simulated post-sampling environments that filters may be exposed to and included: storage at 40 °C for up to 96 h, storage at ?16 °C for 48 h, and storage at room temperature (～21 °C) for 48 h. Carbon mass on the filters was measured using a thermal-optical method. The total carbon (TC), total organic carbon (TOC) and total elemental carbon (TEC) as well as carbon thermal fraction masses were obtained. Statistical analyses were performed to identify significant differences in carbon fraction concentrations between filters analyzed immediately after sampling and after being subjected to treatment.TOC and TC concentrations decreased by on average 15 ± 5% and 10 ± 4%, respectively, for filters maintained at 40 °C for 96 h but did not change for filters stored at room temperature or frozen for 48 h. TEC did not change for any of the filter treatments. The mass concentration for the organic carbon thermal fraction that evolves at the lowest temperature step (OC1) decreased with increasing storage time at 40 °C with average losses of 70 ± 7% after 96 h. Therefore, OC1 is not a stable measurement due to post-sampling conditions that may be encountered. This work demonstrates that TOC and TC can have substantial measurement artifacts on filters subjected to field latency and other non-temperature controlled post-sampling handling, compared to the carbon loadings on the filter at the end of the sampling period.     

Alkali borosilicate glass by fly ash from a coal-fired power plant

The possibility of using coal fly ash as a silica source for alkali borosilicate glass was investigated. Alkali borosilicate glasses were prepared from the coal fly ash mixed with 30 wt.% reagents composed of Na(2)O and B(2)O(3) by susceptor-induction heating. Their densities ranged from 2.24 to 2.55 g cm(-3) and decreased as the amount of B(2)O(3) addition increased. However, the Vickers microhardness showed a different tendency with the density since the glass network connectivity improved by boron anomaly, which was identified by a nuclear magnetic resonance analysis. The Vickers microhardness of the glass product, with the addition of 15 wt.% B(2)O(3) and 15 wt.% Na(2)O, was about 4030 MPa. Furthermore, the changes in microstructure were consistent with those in the chemical stability by the toxicity characteristic leaching procedure (TCLP).