Performance of different macrophytes in the decontamination of and electricity generation from swine wastewater via an integrated constructed wetland-microbial fuel cell process

Plants constitute a major element of constructed wetlands(CWs).In this study,a coupled system comprising an integrated vertical flow CW(IVCW) and a microbial fuel cell(MFC) for swine wastewater tre atment was developed to research the effects of macrophytes commonly employed in CWs,Canna indica,Acorus calamus,and Ipomoea aquatica,on decontamination and electricity production in the system.Because of the different root types and amounts of oxygen released by the roots,the rates of chemical oxygen demand(COD) and ammonium nitrogen(NH_4~+-N) removal from the swine wastewater differed as well.In the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,the COD removal rates were 80.20%,88.07%,84.70%,and 82.20%,respectively,and the NH_4~+-N removal rates were 49.96%,75.02%,70.25%,and 68.47%,respectively.The decontamination capability of the Canna indica system was better than those of the other systems.The average output voltages were 520±42,715±20,660±27,and 752±26 mV for the unplanted,Canna indica,Acorus calamus,and Ipomoea aquatica systems,respectively,and the maximum power densities were 0.2230,0.4136,0.3614,and0.4964 W/m~3,respectively.Ipomoea aquatica had the largest effect on bioelectricity generation promotion.In addition,electrochemically active bacteria,Geobacter and Desulfuromonas,were detected in the anodic biofilm by high-throughput sequencing analysis,and Comamonas(Proteobacteria),which is widely found in MFCs,was also detected in the anodic biofilm.These results confirmed the important role of plants in IVCW-MFCs.     

Effects of SO2 and H2O on low-temperature NO conversion over F-V2O5-WO3/TiO2 catalysts

F-V_2 O_5-WO3/Ti02 catalysts were prepared by the impregnation method.As the content of F ions increased from 0.00 to 0.35 wt.%,the NO conversion of F-V_2 O_5-WO_3/TiO_2 catalysts initially increased and then decreased.The 0.2 F-V_2 O_5-WO_3/TiO_2 catalyst(0.2 wt.% F ion)exhibited the best denitration(De-NOx) performance,with more than 95% NO conversion in the temperature range 160-360℃,and 99.0% N2 selectivity between 110 and 280℃.The addition of an appropriate amount of F ions eroded the surface morphology of the catalyst and reduced its grain size,thus enhancing the NO conversion at low temperature as well as the sulfur and water resistance of the V_2 O_5-WO3/Ti02 catalyst.After selective catalytic reduction(SCR) reaction in a gas flow containing SO_2 and H_2 O,the number of NH3 adsorption sites,active component content,specific surface area and pore volume decreased to different degrees.Ammonium sulfate species deposited on the catalyst surface,which blocked part of the active sites and reduced the NO conversion performance of the catalyst.On-line thermal regeneration could not completely recover the catalyst activity,although it prolonged the cumulative life of the catalyst.In addition,a mechanism for the effects of S02 and H_2 O on catalyst NO conversion was proposed.     

Fast and efficient aqueous arsenic removal by functionalized MIL-100(Fe)/rGO/δ-MnO2 ternary composites: Adsorption performance and mechanism

Because of its significant toxicological effects on the environment and human health,arsenic(As) is a major global issue.In this study,an Fe-based metal-organic framework(MOF)(Materials of Institut Lavoisier:MIL-100(Fe)) which was impregnated with reduced graphene oxide(rGO) by using a simple hydrothermal method and coated with birnessitetype manganese oxide(δ-MnO_2) using the one-pot reaction process(MIL-100(Fe)/rGO/δ-MnO_2 nanocomposites) was synthesized and applied successfully in As removal.The removal efficiency was rapid,the equilibrium was achieved in 40 min and 120 min for As(Ⅲ) and As(Ⅴ),respectively,at a level of 5 mg/L.The maximum adsorption capacities of As(Ⅲ) and As(Ⅴ) at pH 2 were 192.67 mg/g and 162.07 mg/g,respectively.The adsorbent revealed high stability in pH range 2-9 and saturated adsorbent can be fully regenerated at least five runs.The adsorption process can be described by the pseudo-second-order kinetic model and Langmuir monolayer adsorption.The adsorption mechanisms consisted of electrostatic interaction,oxidation and inner sphere surface complexation.     

武当山夏季颗粒物数浓度谱分布特征及气团来源影响研究

为研究大气边界层中上层大气颗粒物的数浓度谱分布特征及气团来源的影响,于2018年6月利用3080型SMPS粒径谱仪对武当山14.6~660 nm颗粒物数浓度谱进行观测,分析和探讨了其数浓度谱分布及日变化特征,并结合后向轨迹、潜在源贡献因子法（PSCF）与浓度权重轨迹分析法（CWT）探讨对武当山颗粒物数浓度影响较大的外源输送路径和贡献源区.结果表明:①武当山大气颗粒物主要以爱根模态为主,平均数浓度为2 500个/cm3,积聚模态、核膜态平均数浓度分别为2 265、359个/cm3,3种模态数浓度分别占总数浓度的48.79%、44.21%、7.01%.②在新粒子生成日,核膜态数浓度于10:00开始上升,11:00—17:00的核膜态数浓度相对较高,约2 000个/cm3.新粒子生成日ρ（SO₂）与ρ（O₃）的日变化趋势均与核模态数浓度较为相似,表明SO₂和O₃参与光化学反应后的产物（硫酸及有机物）有利于新粒子的生成与增长.新粒子生成日风速、温度均大于非新粒子生成日,但相对湿度较低.③在东部及局地气团影响下大气颗粒物主要以积聚模态为主,数浓度分别为2 311和2 596个/cm3;核模态、爱根模态数浓度在受西北气团影响时最大,数浓度分别为806和3 078个/cm3.④潜在源区分析表明,影响武当山积聚模态数浓度的主要源区为十堰市本地及襄阳市,二者贡献值在840个/cm3以上.研究显示,武当山颗粒物主要以爱根模态为主,颗粒物数浓度日变化主要受大气边界层发展及山谷风的影响,较高的ρ（SO₂）与ρ（O₃）以及高温、低湿及较大的风速均有利于新粒子的生成,周边城市的区域性传输对武当山颗粒物的影响较大.      

京津冀城市群二氧化碳排放达峰研究

基于IPCC排放因子方法建立了2015—2019年京津冀城市群地级城市CO₂排放清单,基于经济增长与CO₂排放关系的脱钩系数法,得到京津冀城市群13个地级以上城市的脱钩情况,结合历史CO₂排放和脱钩情况提出的京津冀城市群达峰判别方法,对京津冀城市群地级以上城市CO₂排放达峰情况进行了判断。结果表明:近5年来,保定、张家口、秦皇岛、邢台、沧州、廊坊、衡水7市碳排放量暂未达到峰值状态;北京、天津、石家庄、承德、邯郸、唐山6个城市已经处于CO₂排放达峰状态。建议已经具备达峰条件的城市抓紧开展达峰行动方案,制定CO₂排放达峰目标。     

长江中下游环境DNA宏条形码生物多样性检测技术初步研究

长江生物多样性在人为影响下面临严重威胁,物种监测是生物多样性保护的基础,为完善长江水生态监测体系,实现高效无损伤的物种监测,在长江中下游干流3个江段（新滩、安庆和芜湖）采集水样,建立长江水样环境DNA宏条形码物种检测体系并评估其有效性.结果表明:①长江中下游环境DNA宏条形码检测到32个物种,包括20种鱼类、1种水生哺乳动物（长江江豚）和11种陆生动物,其中鱼类物种包括鲤形目、鲇形目、鲈形目和鲱形目,其种数占鱼类总种数的比例分别为60%、25%、10%和5%.②长江中下游渔获物中资源量居首位的鲤形目在环境DNA调查中序列数最多,占鱼类总序列的96.2%,其次为鲱形目（占比为3.5%）,鲇形目和鲈形目占比较低,分别为0.2%和0.1%,4个类目序列相对丰度与渔获物种资源量组成差异较大.③环境DNA调查次数约占传统渔获物调查次数的几十至几百分之一,采样时间不足努力量最少的渔获物调查的1%,检测到的鱼类种数为传统调查总数的31%~49%.④安庆采样点位于长江中下游长江江豚密度最高的江段,其环境DNA检出率和序列相对丰度在3个采样点中均最高.研究显示:长江水样环境DNA包含水陆复合生态系统的生物多样性信息,利用水样环境DNA宏条形码可检测不同类群的水生和陆生物种;对于鱼类物种检测,环境DNA宏条形码比传统调查方法效率更高,可对传统调查结果进行补充;环境DNA宏条形码生物多样性检测主要受分子标记体系和核酸序列数据库限制,获取全面的物种多样性和资源量信息需要对检测分析方法进行进一步完善.      

基于模糊PI控制的瞬态高温控制策略研究

目的通过地面环境试验研究气动热引起的瞬态高温环境对飞行器结构的影响。方法设计基于石英灯和离心机的瞬态高温-加速度复合试验系统,研究温度和加速度同步控制系统的结构和原理,分析无制冷装置环境下瞬态高温控制的难点,提出基于模糊PI控制器的温度控制策略。结果通过MATLAB仿真验证,设计的模糊PI控制器相比传统的PI控制器能够有效提高温度控制的动态性能与精确性。结论将基于模糊PI控制的瞬态加热控制策略应用于瞬态高温控制是可行、有效的,能为地面气动热模拟环境试验提供技术保障。     

重金属离子对肺表面活性物质单层膜的影响

为了探究重金属对肺表面活性物质（PS）膜的影响,利用Langmuir–Wilhelmy膜天平,研究了不同种类和浓度的重金属离子与PS单层膜的相互作用.发现Cr³⁺、Cu²⁺、Hg²⁺、Pb²⁺、Cd²⁺、Ni²⁺6种重金属离子均使PS单层的π-A等温线G-LE相变阶段外扩,而Fe³⁺可诱导单层缩合.随后,选取Cd²⁺,Cu²⁺,Hg²⁺,Fe³⁺4种离子进一步探究了重金属浓度对PS单层膜表面活性的影响规律,进行了可压缩模量分析,并结合红外光谱（FTIR）和原子力显微镜（AFM）探究其作用机理,发现Cu²⁺,Fe³⁺和Hg²⁺均会以浓度依赖的方式与PS单层的极性头部发生络合作用,形成复合物,改变膜的稳定性;而Cd²⁺的影响明显弱于其他3种金属离子,但也能使得PS单层有序性增强.     

石灰对生物炭和腐殖酸阻控水稻Cd吸收的效应

采用田间试验,研究了石灰-生物炭和石灰-腐殖酸两种联合修复剂及其不同施用量对酸性土壤中稻米Cd含量、产量和品质的影响,并对不同处理修复效果进行综合评估.结果表明,两种联合修复剂能显著降低稻米Cd含量17.39%~45.96%,降低土壤有效Cd含量18.29%~29.88%,.生物炭、腐殖酸施用量分别为5000,6000kg/hm²时,稻米Cd的降低效果最佳.石灰-生物炭处理中,降低稻米Cd含量的主要因子为土壤pH和土壤有效Cd含量（P<0.05）,而石灰-腐殖酸处理则为土壤有机质含量与土壤有效Cd含量（P<0.05）.施加修复剂后稻米产量可达6637~7890kg/hm²,直链淀粉含量达到19.47%~27.26%;当腐殖酸施用量为7500kg/hm²时可使稻米产量提高10.97%,而石灰-生物炭处理对稻米产量无显著影响;采用层次分析法确定了稻米Cd含量、稻米产量、稻米品质和修复费用在修复效应评估中所占权重为0.608、0.150、0.102、0.140,综合评估结果显示土壤-水稻系统Cd阻控效应的联合修复技术为：在施用1200kg/hm²石灰的基础上同时施加6000kg/hm²腐殖酸.