Seasonal Fluctuation in Heavy Metal Pollution in Iran´s Siahroud River - A Preliminary Study (7 pp)

Background The management of its available water resources has become a key issue for Iran. During the last few decades, the water quality of Siahroud River in the coastal plain of the Caspian Sea in Gilan Province in Northern Iran has significantly degraded. The scarcity of water has been compounded by rapid population growth and increasing pollution from fertilizers, pesticides, and municipal and industrial wastes. One of the sources of this degradation is the movement of heavy metals from the river's watershed into the various water systems supported by the river, including the water system for Rasht City. Methods To study the magnitude of heavy metal pollution in the Siahroud River, seven heavy metals including Zn, Cu, Pb, Cd, Mn, Fe, and Ni were measured in duplicate from replicated water samples collected over five consecutive seasons and analyzed by Atomic Absorption Spectrometry. In situ measurements of pH were taken with the samples and total organic carbon (TOC) was analyzed by IR gas measurement. Results The results demonstrated that four of the seven heavy metals including Pb, Fe, Cd, and Mn exceeded permissible safe levels as established by the United States Environmental Protection Agency. Multivariate factor analysis suggested that industrial land-use was the main contributing factor for the high levels of Fe and Mn in the Siahroud River, whereas, Cd was principly from agricultural activities in the watershed. The data also suggested that pH and TOC had an important role in the behaviour of Pb and Mn, and that the elevated levels of these two heavy metals in Siahroud River was the consequence of other anthropogenic sources. Only negligible levels of Zn, Cu and Ni were detected. Finally, all the sampling stations were subjected to cluster analysis. The results indicated that three different zones could be distinguished according to the levels of pollution. In addition, it was shown that the urban areas did not have a significant impact on the heavy metal pollution in the river. This observation stems from the fact that the data from the sampling stations before and after Rasht City were not significantly different. Recommendation . Preventive measures need to be undertaken in the land-use systems and watersheds of the Siahroud River to reduce the pollution levels of Pb, Cd, Mn and Fe.     

Effectiveness of UV/SO32− advanced reduction process for degradation and mineralization of trichlorfon pesticide in water: identification of intermediates and toxicity assessment

Environmental Science and Pollution Research - This study aimed to investigate the degradability, mineralization, proposed decomposition pathway, intermediate products, and toxicity of effluent...     

The dynamic nexus between air transport,technological innovation,FDI, and economic growth: evidence from BRICS-MT countries

Environmental Science and Pollution Research - This study examines the endogenous growth theory for technological innovation and economic growth with the role of foreign direct investment (FDI) and...     

Performance evaluation of a bipolar electrolysis/electrocoagulation (EL/EC) reactor to enhance the sludge dewaterability

The present study aimed to evaluate the performance of a bipolar electrolysis/electrocoagulation reactor designed to enhance the sludge dewaterability. The reactor was 15 L in volume, with two series of plates used in it; Ti/RuO₂ plates for the electrolysis of the sludge, and also aluminum and iron plates for electrocoagulation process. The dewaterability of the sludge was determined in terms of its capillary suction time (CST) and specific resistance to filtration (SRF), while the degree of sludge disintegration was determined based on the value of degree of sludge disintegration (DD_SCOD). The maximum reduction in CST and SRF was observed at a detention time of 20 min and a voltage of 30 V. However, increasing of both detention time and voltage significantly increased the values of CST and SRF even to an extent that they both exceeded those of the untreated sludge. The optimal degree of sludge disintegration achieved by the present study was 2.5%, which was also achieved at a detention time of 20 min and a voltage of 30 V. As reported previously, increased DD_SCOD values led to increasing CST and SRF values, due primarily to the disruption of the sludge flocs. According to the results from the present study, it can be concluded that simultaneous application of electrocoagulation and electrolysis is effective in enhancing the sludge dewaterability, because electrocoagulation helps to achieve a higher degree of sludge disintegration while maintaining the desired sludge dewaterability.     

Energy consumption,emissions and economic growth in Bahrain

This study examines the Granger causality relationships between economic growth, energy consumption and emissions, from 1980 to 2007 in Bahrain, controlling for capital and urban population using Toda and Yamamoto’s approach. It was found that there is unilateral causality which runs from urban population, economic growth, capital and energy consumption to environment. Further, we found strong support for causality running from economic growth to energy consumption, emissions and capital. The existence of these linkages suggests that the government of Bahrain may pursue energy efficiency strategies and carbon emissions reduction policy in the long run without impeding economic growth. Additionally, the long run pursuit of high economic growth given sustained increases in energy efficiency may also reduce CO₂ emissions intensity per unit of her GDP.     

External force-assisted laser forming process for gaining high bending angles

Laser forming process is used in forming and bending of metallic and non-metallic sheets. Laser beam irradiation causes a localized temperature increase and a localized mechanical strength decrease. In this article, an external mechanical force is added to a laser beam irradiation, which is called external force-assisted laser forming process, to gain a 90-degree bending angle. Furthermore, Numerical simulation of the process is performed to achieve a good understanding of the process. Simulation results show that more than two-third of the final forming is due to the laser beam irradiation. Equivalent plastic strain values during laser forming and external force-assisted laser forming processes are compared. Results show that equivalent plastic strain in laser forming process increases in a step pattern, with increasing in scan pass numbers. This occurs because when the laser beam irradiates on the sheet surface, it reduces the yield strength of the sheet. Equivalent plastic strain in external force-assisted laser forming process has an oscillatory step nature. This attributes to simultaneous effects of strain hardening and thermal induced reduction of yield strength of the sheet. Simulations were in good accordance with experiments.     

Investigation of the association between pesticide exposure and the prevalence of type 2 diabetes in Shahedieh population in Yazd

Environmental Science and Pollution Research - This study aimed to investigate the effect of exposure to pesticides and the prevalence of type 2 diabetes (T2D). In a cross-sectional study with a...     

Effect of biocides on the precipitation of calcium fluoride in the presence of anionic copolymeric inhibitors

The inhibitory efficiency of anionic copolymers and the effect of the biocides sodium hypochlorite, glutaraldehyde, and tris(hydroxymethyl)nitromethane on the precipitation behavior of calcium fluoride (CaF₂) were studied. The efficiency of polymeric inhibitors was traced from conductivity measurements by using half-life (t_1/2) method. X-ray diffraction parameters have been measured for calcium fluoride scale minerals. An anionic copolymer (K-798) acts as one of the best inhibitors for the precipitation process of the calcium fluoride in water as compared to K-775. It is assigned to the fact that the copolymer (K-798) contains both sulfonic acid and sulfonated styrene groups while the polymer (K-775) having only the sulfonic acid group. It was further observed that the biocides have no appreciable effect on the performance of the anionic polymeric inhibitors.