Potential of secondary aerosol formation from Chinese gasoline engine exhaust

Light-duty gasoline vehicles have drawn public attention in China due to their significant primary emissions of particulate matter and volatile organic compounds(VOCs). However,little information on secondary aerosol formation from exhaust for Chinese vehicles and fuel conditions is available. In this study, chamber experiments were conducted to quantify the potential of secondary aerosol formation from the exhaust of a port fuel injection gasoline engine. The engine and fuel used are common in the Chinese market, and the fuel satisfies the China V gasoline fuel standard. Substantial secondary aerosol formation was observed during a 4–5 hr simulation, which was estimated to represent more than 10 days of equivalent atmospheric photo-oxidation in Beijing. As a consequence, the extreme case secondary organic aerosol(SOA) production was 426 ± 85 mg/kg-fuel, with high levels of precursors and OH exposure. The low hygroscopicity of the aerosols formed inside the chamber suggests that SOA was the dominant chemical composition. Fourteen percent of SOA measured in the chamber experiments could be explained through the oxidation of speciated single-ring aromatics. Unspeciated precursors, such as intermediate-volatility organic compounds and semi-volatile organic compounds, might be significant for SOA formation from gasoline VOCs. We concluded that reductions of emissions of aerosol precursor gases from vehicles are essential to mediate pollution in China.     

The effects of autophagy on vascular endothelial cells induced by airborne PM2.5

The purpose of this study was to examine the direct toxicity of PM2.5 collected from Beijing on human umbilical vein endothelial cells(HUVEC). A Cell Counting Kit 8(CCK8) assay demonstrated that PM2.5 exposure decreased the proliferation of HUVECs in a dosedependent manner. We also found that PM2.5 exposure induced autophagy in HUVECs, as evidenced by:(1) an increased number of double-membrane vesicles;(2) enhanced conversion and punctuation of the microtubule-associated protein light chain 3(LC3); and(3) decreased levels of the selective autophagy substrate p62 in a time-dependent manner.Furthermore, promoting autophagy in PM2.5-exposed HUVECs with rapamycin increased the cell survival rate, whereas inhibiting autophagy via 3-methyladenine significantly decreased cell survival. These results demonstrate that PM2.5 exposure can induce cytotoxicity and autophagy in HUVECs and that autophagy play a protective role against PM2.5-induced cytotoxicity. The findings of the present study imply a direct toxic effect of PM2.5 on HUVECs and provide novel insight into the mechanism of cardiovascular diseases caused by PM2.5 exposure.     

7B04铝合金和30CrMnSiA钢短期腐蚀的电化学行为研究

目的研究7B04铝合金和30CrMnSiA合金钢试样的电化学性能。方法采用电化学实验、扫描电子显微镜(SEM)、腐蚀坑深度测试分别对7B04铝合金和30CrMnSiA合金钢试样在是否经过天然海水浸泡的情况下进行测试分析,得到微观腐蚀形貌和腐蚀坑深度以及试样表面不带锈和带锈时的电化学性能。结果随着Na Cl浓度增大,7B04铝合金和30CrMnSiA钢的自腐蚀电流变大,两者之间存在明显的电位差,接触后会发生电偶腐蚀。电偶电流与阴阳极面积比和Na Cl浓度有关,阴阳极面积比增大或Na Cl浓度升高均会导致电偶效应增强。经过海水短期浸泡后,7B04铝合金表面的锈层不仅没有起到抑制腐蚀的作用,反而使自腐蚀加重,但电偶效应确实有所减弱。结论沿海设备在使用过程中应竭力避免铝合金在锈层下工作。     

飞机用铝合金腐蚀行为和腐蚀预测研究现状及问题分析

针对不同的航空铝合金结构及部位,从腐蚀机理、腐蚀行为和腐蚀预测技术三方面较为系统地分析了研究现状及进展。在此基础上,明确了航空铝合金腐蚀预测技术需要进一步研究的问题,分别为飞机结构表面腐蚀环境的确定问题,材料在海洋大气环境下腐蚀电化学性能的准确测量问题,腐蚀预测模型的选取问题。     

石墨烯在防腐涂料中的研究进展及应用

简要叙述了石墨烯结构性能以及当前主流制备石墨烯的方法。概述了最近几年来石墨烯在防腐涂料中的研究进展情况,包括石墨烯在涂料中的添加量、分散技术、原位改性等对涂料性能的影响。研究表明,在涂层中分散均匀添加量适中的石墨烯可以对防腐涂料性能有较大的提升,探讨了石墨烯在防腐涂层中的应用机理,同时对石墨烯防腐涂料的应用发展进行了展望。     

空空导弹定延寿技术应用研究

介绍了国外典型的定延寿方法,以美国为代表采用的跟踪监测法和以俄罗斯为代表采用的加速试验法,之后概述了国内常用的厂内寿命试验法、领先使用法、外场信息法、工程分析法、加速试验法。在此基础上,总结了适用于国内空空导弹开展定延寿工作的方法,最后对深入开展空空导弹定延寿技术研究提出了几点建议。     

电絮凝净化含聚污水影响因素研究

目的为保障油田正常安全生产,促进油田含聚污水的循环利用。方法采用电絮凝技术单因素研究方法开展净化含聚污水的静态实验研究,探讨外加电流密度、极板间距、初始pH及聚合物浓度等因素对净化效果的影响规律。结果当初始pH为7.0,电流密度为4.0 m A/m2,极板间距为1.0 cm,电解16 min时,综合处理效果最佳。此时,含油量与浊度去除率分别为98.85%,99.93%,处理每克油平均消耗为0.0494 g的Al,处理每立方米含聚污水的能耗为0.2895 k Wh。污水中的聚合物浓度越小,净化效果越好。结论中性处理,极板间距为1.0 cm,外加电流密度为4.0 m A/m2,通电16 min是最佳处理条件。     

碳量子点掺杂氮化碳提高的光电化学阴极保护性能研究

目的研究g-C_3N_4/C-Dots-M复合材料的光电化学阴极保护性能。方法采用X射线衍射(XRD)、扫描电子显微镜(SEM)和紫外可见漫反射光谱技术对样品的晶体结构、微观形貌和光吸收性能进行表征。通过电化学测试可见光照射下g-C_3N_4/C-Dots-M复合材料光电极偶联316L不锈钢后的光电化学阴极保护电流密度和电位变化曲线,研究材料的光电化学阴极保护性能。结果可见光照射下,该偶联体系的光致混合电位下降至-0.43 V(vs. Ag/AgCl),光电化学阴极保护电流密度达到4.3μA/cm。结论得益于碳量子点优异的电子传导特性,g-C_3N_4/C-Dots-550复合材料的光电化学阴极保护性能比纯g-C_3N_4的明显增强。该复合材料在光电化学阴极保护方面展现了较大的应用潜力。     

硫酸盐还原菌对EH40焊接钢海水腐蚀的影响

目的研究无菌和SRB体系中EH40钢焊接接头的母材区、热影响区和焊缝区腐蚀差异。方法利用金相显微镜观察、失重法、电化学测试、扫描电镜和X射线光电子能谱仪等分析手段。结果焊缝区微观组织由块状铁素体(BLF)和魏氏组织(W)组成;热影响区可再分为粗晶区(CGHAZ)和细晶区(FGHAZ)两个区;母材区主要由BLF、AF和少量珠光体组成。在无菌对照体系中,焊缝区腐蚀速率为0.0026 mm/a,混合区次之,为0.0023 mm/a,母材区最小,为0.0019 mm/a。含SRB体系中,各区的腐蚀速率为:焊缝区(0.0037 mm/a)混合区(0.0034 mm/a)母材区(0.0030 mm/a)。热影响区腐蚀产物形貌粗大,点蚀孔也较大。结论焊缝区比母材区容易腐蚀,由此易造成小阳极大阴极加速腐蚀,热影响区容易发生点蚀。SRB能促进三个区域试样腐蚀加速。     

马莲河流域河水化学特征和化学风化过程分析

采用Gibbs图解和端元分析方法研究了马莲河水化学特征、离子来源和化学风化作用,利用质量平衡正演模型评价了各风化作用对水化学组分的贡献率。结果表明,马莲河水为高TDS咸水,阳离子以Na~+、Mg~(2+)为主,阴离子以Cl~-、SO_4~(2-)为主;沿河水流向TDS降低,水化学类型由Cl-Na型演变为HCO_3·SO_4-Na·Mg型;河水化学组分的主要形成作用为化学风化,蒸发盐主导了流域风化过程,对离子组分平均贡献率高达76.5%,硅酸盐和碳酸盐风化较弱;化学风化具空间变异,从上游到下游,硫酸盐和碳酸盐贡献率增加,岩盐贡献率降低。岩性是控制流域化学风化作用的首要因素,降雨量和径流量可能也有一定影响。