Effect of manure application timing, crop, and soil type on nitrate leaching

Timing of manure application affects N leaching. This 3-yr study quantified N losses from liquid manure application on two soils, a Muskellunge clay loam and a Stafford loamy sand, as affected by cropping system and timing of application. Dairy manure was applied at an annual rate of 93 800 L ha(-1) on replicated drained plots under continuous maize (Zea mays L.) in early fall, late fall, early spring, and as a split application in early and late spring. Variable rates of supplemental sidedress N fertilizer were applied as needed. Manure was applied on orchardgrass (Dactylis glomerata L.) in split applications in early fall and late spring, and early and late spring, with supplemental N fertilizer topdressed as NH4NO3 in early spring at 75 kg N ha(-1). Drain water was sampled at least weekly when lines were flowing. Three-year FWM (flow-weighted mean) NO3-N concentrations on loamy sand soil averaged 2.5 times higher (12.7 mg L(-1)) than those on clay loam plots (5.2 mg L(-1)), and those for fall applications on maize-cropped land averaged >10 mg L(-1) on the clay loam and >20 mg L(-1) on the loamy sand. Nitrate-N concentrations among application seasons followed the pattern early fall > late fall > early spring = early + late spring. For grass, average NO3-N concentrations from manure application remained well below 10 mg L(-1). Fall manure applications on maize show high NO3-N leaching risks, especially on sandy soils, and manure applications on grass pose minimal leaching concern.     

Iron and arsenic release from aquifer solids in response to biostimulation

Biostimulation has been used at various contaminated sites to promote the reductive dechlorination of trichloroethylene (TCE), but the addition of carbon and energy donor also stimulates bacteria that use Fe(III) as the terminal electron acceptor (TEA) in potential competition with dechlorination processes. Microcosm studies were conducted to determine the influence of various carbon donors on the extent of reductive dissolution of aquifer solids containing Fe(III) and arsenic. Glucose, a fermentable and respirable carbon donor, led to the production of 1500 mg Fe(II) kg(-1), or 24% of the total Fe in the aquifer sediment being reduced to Fe(II), whereas the same concentration of carbon as acetate resulted in only 300 mg Fe(II) kg(-1) being produced. The biogenic Fe(II) produced with acetate was exclusively associated with the solid phase whereas with fermentable carbon donors as whey and glucose, 22 and 54% of the Fe(II) was in solution. With fermentation, some of the metabolites appear to be electron shuttling chemicals and chelating agents that facilitate the reductive dissolution of even crystalline Fe(III) oxides. Without the presence of electron shuttling chemicals, only surficial Fe in direct contact with the bacteria was bioavailable, as illustrated when acetate was used. Regardless of carbon donor type and concentration, As concentrations in the water exceeded drinking water standards. The As dissolution appears to have been the result of the direct use of As as an electron acceptor by dissimilatory arsenic reducing bacteria. Our findings indicate that selection of the carbon and energy donor for biostimulation for remediation of chlorinated solvent impacted aquifers may greatly influence the extent of the reductive dissolution of iron minerals in direct competition with dechlorination processes. Biostimulation may also result in a significant release of As to the solution phase, contributing to further contamination of the aquifer.     

Behavior of an aerated submerged fixed-film reactor (ASFFR) under simultaneous organic and ammonium loading

The performance of an aerated submerged fixed-film reactor (ASFFR) under simultaneous organic and ammonium loading and its effect on nitrification was studied. Organic loadings varied in the range of 1.93 to 5.29 g chemical oxygen demand (COD) m-2 d-1 and NH4-N loadings were in the range of 116 to 318 mg NH4-N m-2 d-1. Increments of loading rates were obtained both by increasing the flow rate and increasing the influent substrate in individual pilot runs. Results showed that with organic loading rates up to 3.97 g COD m-2 d-1, complete nitrification was achievable. Although high organic loading such as 5.29 g COD m-2 d-1 could cause nitrification to stop, shifting to lower organic loadings made nitrification start and set rapidly to its previous steady-state concentrations. Comparison of results showed that in the ASFFR, nitrification would be severely affected by an organic loading rate of 5.29 g COD m-2 d-1 by increasing either the flow or the influent substrate. It should be noted that the average value of dissolved oxygen was 3.4 mg L-1 with an air supply of 15 L min-1, and there was no indication of oxygen limitation. The results of this study show the flexibility of ASFFRs under changing organic loads. Furthermore, for achieving complete nitrification and optimum application of these reactors for protecting receiving water from the environmental hazards of ammonium, the maximum organic loading that would present complete nitrification should be considered.     

Electroosmotic dewatering of dredged sediments: bench-scale investigation

The Indiana Harbor (Indiana, USA) has not been dredged since 1972 due to lack of a suitable disposal site for dredged sediment. As a result of this, over a million cubic yards of highly contaminated sediment has accumulated in the harbor. Recently, the United States Army Corps of Engineers (USACE) has selected a site for the confined disposal facility (CDF) and is in the process of designing it. Although dredging can be accomplished rapidly, the disposal in the CDF has to be done slowly to allow adequate time for consolidation to occur. The sediment possesses very high moisture content and very low hydraulic conductivity, which cause consolidation to occur slowly. Consolidation of the sediment is essential in order to achieve adequate shear strength of sediments and also to provide enough air space to accommodate the large amount of sediment that requires disposal. Currently, it has been estimated that if a one 3-foot (0.9-m) thick layer of sediment was disposed of at the CDF annually, it would take approximately 10 years to dispose of all the sediment that is to be dredged from the Indiana Harbor. This study investigated the feasibility of using an electroosmotic dewatering technology to accelerate dewatering and consolidation of sediment, thereby allowing more rapid disposal of sediment into the CDF. Electroosmotic dewatering essentially involves applying a small electric potential across the sediment layer, thereby inducing rapid flow as a result of physico-chemical and electrochemical processes. A series of bench-scale electrokinetic experiments were conducted on actual dredged sediment samples from the Indiana Harbor to investigate dewatering rates caused by gravity alone, dewatering rates caused by gravity and electric potential, and the effects of the addition of polymer flocculants on dewatering of the sediments. The results showed that electroosmotic dewatering under an applied electric potential of 1.0VDC/cm could increase the rate of dewatering and consolidation by an order of magnitude as compared to gravity drainage alone. Amending the sediment with polymers at low concentrations (0.5-1% by dry weight) will enhance this dewatering process; however, the optimal polymer concentration and the cost-effectiveness of using polymers should be investigated further.     

Recycling of an industrial sludge and marine clay as light-weight aggregates

The geographical limitations of Singapore, its restricted natural resources and voluminous municipal and industrial waste streams, make environmental management a major challenge for the island state. In an attempt to find ways to reduce importation of raw materials and the waste sent to landfill, light weight aggregates were produced from marine clay and a CaF(2)-rich semiconductor industry sludge. Aggregates were produced in a bench-scale rotary kiln with three clay/sludge loadings (90/10, 70/30 and 50/50%). All three mixtures showed good bloating behavior during firing and the ceramic pellets (1-1.5cm diameter) had densities well below that required for light-weight aggregates. In the initial tests, the pore sizes of the aggregates were in general too large resulting in high water absorption. Comparisons between the composition of the two waste products and the aggregates showed a significant loss of fluorine (40-60%) during processing; a problem which may require flue gas treatment. Leach testing showed that the formed aggregates would not pose a human or environmental hazard in terms of fluorine mobilization.     

Management of mine spoil for crop productivity with lignite fly ash and biological amendments

Long-term field trials using lignite fly ash (LFA) were carried out in rice crops during the period 1996-2000 at Mine I, Neyveli Lignite Corporation, Tamil Nadu. LFA, being alkaline and endowed with an excellent pozzolanic nature, silt loam texture, and plant nutrients, has the potential to improve the texture, fertility, and crop productivity of mine spoil. The rice crops were the first, third, fifth, and sixth crops in rotation. The other crops, such as green gram (second) and sun hemp (fourth), were grown as green manure. For experimental trials, LFA was applied at various dosages (0, 5, 10, 20, 50, 100, and 200 t/ha), with and without press mud (10 t/ha), before cultivation of the first crop. Repeat applications of LFA were made at the same dosages in treatments of up to 50 t/ha (with and without press mud) before cultivation of the third and fifth crops. Press mud, a lightweight organic waste product from the sugar industry, was used as an organic amendment and source of plant nutrients. Also, a recommended dosage of chemical fertilizer, along with gypsum, humic acid, and biofertilizer as supplementing agents, was applied in all the treatments, including control. With one-time and repeat applications of LFA, from 5 to 20 t/ha (with and without press mud), the crop yield (grain and straw) increased significantly (p < 0.05), in the range from 3.0 to 42.0% over the corresponding control. The maximum yield was obtained with repeat applications of 20 t/ha of LFA with press mud in the third crop. The press mud enhanced the yield in the range of 1.5-10.2% with various dosages of LFA. The optimum dosage of LFA was 20 t/ha for both one-time and repeat applications. Repeat applications of LFA at lower dosages of up to 20 t/ha were more effective in increasing the yield than the corresponding one-time applications of up to 20 t/ha and repeat applications at 50 t/ha. One-time and repeat applications of LFA of up to 20 t/ha (with and without press mud), apart from increasing the yield, evinced improvement in the texture and fertility of mine spoil and the nutrient content of crop produce. Furthermore, some increase in the content of trace and heavy metals and the level of gamma-emitters in the mine spoil and crop produce was observed, but well within the permissible limits. The residual effect of LFA on succeeding crops was also encouraging in terms of eco-friendliness. Beyond 20 t/ha of LFA, the crop yield decreased significantly (p < 0.05), as a result of the formation of hardpan in the mine spoil and possibly the higher concentration of soluble salts in the LFA. However, the adverse effects of soluble salts were annulled progressively during the cultivation of succeeding crops. A plausible mechanism for the improved fertility of mine spoil and the carryover or uptake of toxic trace and heavy metals and gamma-emitters in mine spoil and crop produce is also discussed.     

Environmental assessment of mercury dispersion, transformation and bioavailability in the Lake Victoria Goldfields, Tanzania

Environmental dispersion and transformation of mercury discharged from gold mining operations has been investigated in field and laboratory studies in order to provide better understanding of the degree of mercury (Hg) pollution and bioavailability in the Lake Victoria goldfields (LVGF) ecosystems. This paper reviews results already published elsewhere and presents additional data on Hg dynamics in the LVGF. Studies conducted at the Mugusu and Rwamagaza artisanal mines indicated different degrees of Hg contamination and dispersion in environmental matrices. Mercury concentration in contaminated river sediments near the Mugusu mine varied from 6.0 to 0.5 mg/kg on a dry weight basis. The highest Hg contamination levels (165-232 mg/kg) were associated with mine tailings at the Rwamagaza mine. Mercury concentrations in fish representing different dietary habits on the southwestern shore of Lake Victoria at the Nungwe Bay were very low (2-35 microg/kg) and thought to represent background levels. These and other results suggested that the use of Hg in gold extraction in the LVGF has not caused high Hg levels in lake fish. The study of Hg in lichens showed Parmelia lichen to be an effective bioindicator for atmospheric Hg contamination due to Hg emissions from gold-amalgam firing and purification operations. The Hg levels in the lichens around the Mugusu mine ranged from 3.1 to 0.1 microg/g; the highest levels were recorded in the lichens sampled close to gold-amalgam processing sites. The regional background level in the Parmelia lichen was 0.05-0.10 microg/g, with a mean level of 0.07 microg/g. Studies of Hg transformation in the mine tailings revealed unexpectedly high methylmercury (MeHg) levels in the tailings (629-710 ng/g), which indicated that oxidation and methylation of metallic Hg in the tailings occurred at significant levels under tropical conditions. Re-equilibration of the tailings with freshwater (FW) indicated the MeHg was firmly bound in the tailings and therefore very little MeHg was released to the water column (0.2-1.5 ng/L). The methylation of Hg in tropical loamy clay soil contaminated with HgCl(2) (5 mg Hg/kg) yielded MeHg concentrations of 11 and 14 ng/g when inundated with seawater and FW, respectively, for 4 weeks. Little MeHg was transferred from the soil to the equilibrated water (< or = 0.4 ng/L). Atmospheric exposure of the soil pre-inundated with FW resulted in net degradation of MeHg during the 1st week of exposure, followed by net production and accumulation of MeHg in the soil (up to 15.5 ng/g) during atmospheric desiccation. Mercury uptake by fish from the Hg(0)-contaminated aquatic sediment-tailings system in the aquarium experiment was found to be low, suggesting the low availability of MeHg for bioaccumulation in the system. These and other results provide useful insights into Hg transformation, mobility and bioavailability in tropical aquatic systems affected by Hg pollution from gold mining operations.     

Using Relative Risk to Compare the Effects of Aquatic Stressors at a Regional Scale

The regional-scale importance of an aquatic stressor depends both on its regional extent (i.e., how widespread it is) and on the severity of its effects in ecosystems where it is found. Sample surveys, such as those developed by the U.S. Environmental Protection Agency’s Environmental Monitoring and Assessment Program (EMAP), are designed to estimate and compare the extents, throughout a large region, of elevated conditions for various aquatic stressors. In this article, we propose relative risk as a complementary measure of the severity of each stressor’s effect on a response variable that characterizes aquatic ecological condition. Specifically, relative risk measures the strength of association between stressor and response variables that can be classified as either “good” (i.e., reference) or “poor” (i.e., different from reference). We present formulae for estimating relative risk and its confidence interval, adapted for the unequal sample inclusion probabilities employed in EMAP surveys. For a recent EMAP survey of streams in five Mid-Atlantic states, we estimated the relative extents of eight stressors as well as their relative risks to aquatic macroinvertebrate assemblages, with assemblage condition measured by an index of biotic integrity (IBI). For example, a measure of excess sedimentation had a relative risk of 1.60 for macroinvertebrate IBI, with the meaning that poor IBI conditions were 1.6 times more likely to be found in streams having poor conditions of sedimentation than in streams having good sedimentation conditions. We show how stressor extent and relative risk estimates, viewed together, offer a compact and comprehensive assessment of the relative importances of multiple stressors.     

TUGAI: An Integrated Simulation Tool for Ecological Assessment of Alternative Water Management Strategies in a Degraded River Delta

The development of ecologically sound water allocation strategies that account for the needs of riverine ecosystems is a pressing issue, especially in semiarid river basins. In the Aral Sea Basin, a search for strategies to mitigate ecological and socioeconomic deterioration has been in process since the early 1990s. The Geographic Information System–based simulation tool TUGAI has been developed to support the policy determination process by providing a simple, problem-oriented method to assess ecological effects of alternative water management strategies for the Amudarya River. It combines a multiobjective water allocation model with simple, spatially explicit statistical and rule-based models of landscape dynamics. Changes in environmental conditions are evaluated by a fuzzy habitat suitability index for Populus euphratica, which is the dominant species of the characteristic riverine Tugai forests. Water management scenarios can be developed by altering spatiotemporal water distribution in the delta area or the amount of water inflow into the delta. Outcomes of scenario analysis are qualitative comparisons of the ecological effects of different options for a time period of up to 28 years. The given approach utilizes different types of knowledge, from quantitative hydrological data to qualitative local expert knowledge. The main purpose of the tool is to integrate the knowledge in a comprehensive way to make it available for discussions on alternative policies in moderated workshops with stakeholders. In this article, the modules of the tool, their integration, and three hypothetical scenarios are presented. Based on the experience gained when developing the TUGAI tool, we propose that the general framework can be transferred to other areas where tradeoffs in water allocation between the environment and other water users are of major concern. The potential for a simulation tool to structure and inform a complex resource management situation by involving local experts and stakeholders in the development of possible future scenarios will become increasingly valuable for transparent and participatory resource management.     

近年来珠三角地区大气中痕量氟氯烃(CFCs)的浓度水平与变化特征

用预浓缩-GC/MS方法研究了珠江三角洲大气中的CCl3F、CFC-12、CFC-113和CFC-114等4种痕量氟氯烷烃气体。结果表明,2005年珠江三角洲背景点鼎湖山大气中CFC-12和CFC-11的年平均浓度高于全球本底站,说明珠三角地区还存在一定CFC-11和CFC-12的排放源;CFC-113浓度水平则与全球本底站点浓度接近,且CFC-113和CFC-114在广州城区与鼎湖山差别不显著,表明区内其排放源强度应很小。观测日内广州和鼎湖山大气中四种CFCs的日变化幅度均较小,无明显的昼夜变化规律。广州市CFCs总体呈夏秋高、冬春低的特征,与城区致冷设备高温季节使用频率较大有关;鼎湖山则呈冬春高、夏秋低的特征,主要受扩散作用和季风的影响。初步分析显示,从1997年到2005年,CFC-11、CFC-12和CFC-114浓度总体呈现先上升后缓慢降低的趋势,而CFC-113的浓度一直逐年下降。