A new device for measuring fluctuations in plant stem diameter: Implications for monitoring plant responses

An electrical device capable of continuously measuring micronsized changes in stem diameter of woody and herbaceous plants is described. Fumigation of sunflowers with automotive exhaust was used to test the ability of the device to detect short-term plant responses.     

Integration of modeling,monitoring and laboratory observation to determine reasons for air quality violations

An attempt was made to explain ambient air quality violations in the vicinity of industrial plants. Micrometeorology, diffusion calculaations, ambient readings, and plant engineering data are all taken into consideration to ascertain whether the plant is or is not the principal offender.Scrutiny of hi-vol filters using scanning electron microscopy for particle size analysis and particle chemical make-up as an assessment technique is also described.Case histories using the above analytical techniques are discussed.Presented at the 16th National Conference on Energy and the Environment, May 23, 1979     

Further studies using X-ray fluorescence to sample lead contaminated carpeted surfaces

The sampling of carpeted surfaces to test for lead contamination primarily focuses upon vacuum techniques. Vacuum sampling techniques, however, require time-consuming, expensive laboratory analysis of the dusts obtained and are unable to determine total lead load on the carpet. X-ray fluorescence (XRF) analysis is an on-site, inexpensive, non-destructive, quick technique for predicting metals levels in a variety of media, such as water, soil, filter paper and painted surfaces. A 1992 study of the feasibility of XRF to analyze for lead and soil loadings on carpeted surfaces indicated that XRF can detect lead at a low enough level to warrant further study. This paper expands this earlier study and developes lead and soil loading calibration curves for three different carpet types based upon XRF lead L-beta peak areas and XRF iron and barium K-alpha peak and background areas. Results indicate that variation in the data can be reduced through modifications of the XRF analysis technique, thus reducing the statistically determined detection level, and that carpet type does affect the calibration. Detection levels of approximately 70 mg/m² for lead and 5 g/m² for soil were obtained. Overall, good agreement was found between results of this study and the earlier one. XRF shows excellent potential for quantitative analysis of lead on carpeted surfaces.     

Ammonia uptake by plants

The paper considers the methodology and results of experimental determination of dry deposition and ammonia uptake by isolated plant leaves. Analytical expressions are proposed which allow a transition from rates obtained in an isolated chamber to dry ammonia deposition by standing crops leaves.     

Field scale variability of cadmium and zinc in soil and barley

CaCl₂-extractable soil Cd and Zn contents have been suggested as a measure of bioavailability. To investigate the ability of this measure to reflect spatial patterns of Cd and Zn concentrations in barley (Hordeum vulgare L.) in an arable field, plant and soil samples were taken from a 0.5 ha area sandy soil contaminated with Cd and Zn. Cd and Zn contents in barley and yield were spatially variable. Yield was low, which may have been caused by Zn toxicity or atrazine turnover. For Cd, CaCl₂-extractable soil contents explained only 17% of the variation in Cd contents in grain, and for Zn no significant correlation was observed. Nevertheless, surface plots of CaCl₂-extractable soil contents and contents of barley grain illustrated their corresponding spatial patterns. Despite the poor linear correlation between CaCl₂-extractable soil-Cd and grain-Cd, a stochastic model for long term behaviour of Cd in field soils predicted observed variability in Cd contents of barley grain well from spatial variability of soil pH and organic matter content. The probabilistic model predicted behaviour of Cd in terms of probability, and was more appropriate than the deterministic approach.     

Heavy metals in the SPM of air in the environment surrounding a ferro-alloy industrial plant in India

Prices for ferro-alloys have hardened due to the closure of plants in developed countries on account of increasingly stringent pollution control legislation, resulting in a higher cost of production. A ferro-alloy industry with a capacity of 80000 MT per annum was selected to study the nature of pollution. Because of the objectionable nature of polluting air in and around the plant it was located in a rural area where there was no other industry. The area was agriculturally active and there was no effective control system for this plant.The quality of ambient air around the plant site is discussed in this paper along with the meteorological conditions. The maximum concentration of suspended particulate matter (SPM) was 768 µg/NM³ downwind of the plant, minimum 184 µg/NM³, and the average was more than 446 µg/NM³. The presence of heavy metals, viz. Fe, Mn, Cr and Pb, was also assessed. The concentration of Fe was 50 µg/NM³ downwind and 10 µg/NM³ upwind. The concentration of other metals followed a similar trend.     

Organochlorine contaminant concentrations in caddisfly adults (Trichoptera) collected from great lakes connecting channels

Pennsylvania-style light traps were used to capture adult Trichoptera from the St. Marys, St. Clair, Detroit and Niagara rivers, Canada. Adequate biomass was acquired in single, 2-h collections to permit triplicate gas chromatographic analyses of 1–4 g samples for 36 organochlorine contaminants. Contaminant levels varied unpredictably but relatively little among samples taken at monthly intervals over the summer. Samples collected simultaneously from the two sides of the Detroit R. reflected local sediment contaminant patterns, suggesting limited dispersal by adults. Genus-specific differences in contaminant concentrations within the Hydropsychidae and Leptoceridae probably reflect differences in larval habitats and manner of feeding. Contaminant concentrations and relative composition paralleled published reports of contaminants in sediments from collection locations. St. Marys R. caddisflies contained contaminant levels indistinguishable from samples collected at reference sites. St. Clair R. samples contained high levels of compounds associated with petrochemical industries located in the river's upstream reaches. High levels of polychlorinated biphenyls (PCBs) and most other contaminants in Detroit R. samples reflected industrial loadings near Detroit, Michigan. Niagara R. samples contained elevated concentrations of PCBs and pesticides. Cluster analysis grouped samples into five clusters each with unique contaminant composition. These also corresponded to geographic origin: St. Marys, St. Clair, Detroit and upper and lower Niagara rivers. The relative ease of collection and consistent results obtained render adult Trichoptera potentially valuable candidates for surveys of aquatic contamination over a broad range of geographical and ecological conditions.     

Matrix diffusion effects in the cleanup of heterogeneous aquifers

Simple mathematical models are developed to account for the rather slow mass transport of nonaqueous phase liquid (NAPL) into aqueous solution in groundwater during flushing operations. The models are based on the assumption that this bottleneck in the process is associated with diffusion in the aqueous phase in the porous medium from the location of the NAPL drops/ganglia in a region of relatively low permeability out into a region of substantially higher permeability, somewhat analogous to diffusion from a block of porous rock into a nearby fracture, where the fracture system overwhelmingly dominates the overall permeability. The models include batch flushing, flushing in a laboratory column, and a one-dimensional model for flushing by means of a single recovery well.     

Patchy distributions: Optimising sample size

A method for estimating sample size which does not require an a priori definition of desired precision, or the assumption that the population is normally distributed with constant variance, has recently been proposed. This paper discusses this method and presents five modifications which make the method easier to use and reduce the probability of estimating a larger sample size than is actually required. The method is extended and used to estimate the mean abundance of patchily distributed benthic organisms. The technique can be used to guide the design of any environmental sampling programme, be it physical, chemical or biological, where comparisons between times and/or locations are required. Trade-offs between numbers of replicates and numbers of levels/sites are discussed.