Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Photodegradation of Hexafluoropropylene Oxide Trimer Acid under UV Irradiation

As a novel alternative to traditional perfluoroalkyl substances (PFASs), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), hexafluoroproplyene oxide trimer acid (HFPO-TA) has been detected worldwide in surface water. Moreover, recent researches have demonstrated that HFPO-TA has stronger bioaccumulation potential and higher hepatotoxicity than PFOA. To treat these contaminants e.g. PFOA and PFOS, some photochemical techniques by adding exogenous substances had been reported. However, there is still no report for the behavior of HFPO-TA itself under direct UV irradiation. The current study investigated the photo-transformation of HFPO-TA under UV irradiation in aqueous solution. After 72 hr photoreaction, 75% degradation ratio and 25% defluorination ratio were achieved under ambient condition. Reducing active species, i.e., hydrated electrons and active hydrogen atoms, generated from water splitting played dominant roles in degradation of HFPO-TA, which was confirmed by different effects of reaction atmospheres and quenching experiments. A possible degradation pathway was proposed based on the products identification and theoretical calculations. In general, HFPO-TA would be transformed into shorter-chain PFASs, including hexafluoropropylene oxide dimer acid (HFPO-DA), perfluoropropionic acid (PFA) and trifluoroacetate (TFA). This research provides basic information for HFPO-TA photodegradation process and is essential to develop novel remediation techniques for HFPO-TA and other alternatives with similar structures.     

Concentrations and chemical compositions of PM10 during hazy and non-hazy days in Beijing

In order to study the concentrations of major components,characteristics and comparison in hazy and non-hazy days of PM_(10) in Beijing,aerosol samples were collected at urban site in Beijing from December 29,2014 to January 22,2015.Heavy metals like Zn,Pb,Mn,Cu,As,V,Cr and Cd were deeply studied considering their toxic effects on human being;nine water-soluble inorganic ions(SO_4~(2-),NO_3~-,NH_4~+,Na~+,K~+,Cl~-,Ca~(2+) and Mg~(2+)) and carbon fractions(OC and EC) were also analyzed.The concentrations of heavy metals were 1.03–1.98 times higher in hazy days than those in non-hazy days,mainly due to biomass burning and coal burning.The trends in total heavy metals concentrations were basically consistent with the trends in PM concentrations except for two obvious periods(12.29–12.30;1.14–1.15);but when air masses accumulated locally or around Beijing,trends in PM concentrations and heavy metals were opposite.The proportion for NO_3~-/SO_4~(2-) indicated that mobile sources such as automobiles were important reasons for haze in Beijing.Correlation between OC and EC during non-hazy days was strong(R~2= 0.95) but it was low(R~2= 0.67) during hazy days,and large variations for OC/EC values occurred in hazy days.The calculated mass concentration of SOC is 2.58 μg/m~3,which only accounted for 10.1% of the OC concentration.When air masses from the far north-west,they decreased PM concentration in Beijing and they were relatively clean;however,those from the near east,south-east and south of the mainland increased PM concentration and they were dirty.     

贵州草海湿地溶解性有机物的光谱特征及其与PFASs的相关性分析

为描述草海湿地DOM（dissolved organic matter,溶解性有机物）荧光特征,探究其对PFASs（per-and polyfluoroalkyl substances,全氟及多氟化合物）环境行为造成的影响,利用超高效液相色谱-质谱联用技术和三维荧光光谱技术,结合平行因子分析,开展DOM光谱学特性研究,分析ρ（DOM）与ρ（PFASs）的相关关系.结果表明:①草海湿地中共解析出3类4种荧光组分,分别为类腐殖酸[λ_Ex（360 nm）/λ_Em（450 nm）]、长波段腐殖质[λ_Ex（400 nm）/λ_Em（510 nm）]、类富里酸[λ_Ex（330 nm）/λ_Em（400 nm）]和类色氨酸[λ_Ex（280 nm）/λ_Em（350 nm）],贡献率分别为48.6%、23.6%、22.9%和4.9%,其中类腐殖质总贡献率高达72.2%.在农业生产和人类活动的影响下,总荧光强度大致呈现从入湖区向出湖区逐渐降低、湖心区略高的趋势.②在草海湿地表层水中共检出了12种PFASs,ρ（PFASs）为233.18 ng/L,每种平均值为19.43 ng/L,PFBA（perfluorobutanoic acid,全氟丁酸）是主要污染物;草海湿地入湖区点源影响特征明显,生活污水和农业生产用水是主要的潜在污染源.③相关性分析结果显示,各荧光组分含量均与ρ（PFBS）（potassium perfluorobutanesulfonate,全氟丁烷磺酸）负相关;类色氨酸含量与ρ（PFHpA）（perfluororoheptanoic acid,全氟庚酸）负相关,与ρ（PFTriDA）（perfluorotrideanoic acid,全氟十三酸）则显著正相关.研究显示,草海湿地水体腐殖化程度高,外源特征明显,共检出12种PFASs,初步揭示了草海湿地水环境中ρ（DOM）与ρ（PFASs）的相关关系,其受水体性质及化合物结构等差异的影响,有待进一步开展深入研究.      

基于模糊PI控制的瞬态高温控制策略研究

目的通过地面环境试验研究气动热引起的瞬态高温环境对飞行器结构的影响。方法设计基于石英灯和离心机的瞬态高温-加速度复合试验系统,研究温度和加速度同步控制系统的结构和原理,分析无制冷装置环境下瞬态高温控制的难点,提出基于模糊PI控制器的温度控制策略。结果通过MATLAB仿真验证,设计的模糊PI控制器相比传统的PI控制器能够有效提高温度控制的动态性能与精确性。结论将基于模糊PI控制的瞬态加热控制策略应用于瞬态高温控制是可行、有效的,能为地面气动热模拟环境试验提供技术保障。     

液-弹隔振器设计与试验分析

目的开展液-弹隔振器的设计及试验验证。方法基于反共振原理建立的液-弹隔振器动力学分析模型,推导了其动力学方程。结果建立了液弹隔振器隔振频率与相关参数的关系,依据相关参数完成了液-弹隔振器的设计,并进行了液-弹隔振器动力学性能相关试验,利用动刚度测试法和传递率测试法验证了液-弹隔振器性能,试验验证了液-弹隔振器高静态刚度和隔振频率点下的低动态刚度特点。结论实现了液-弹隔振器的设计,同时液弹隔振器在隔振频率点下达到60%的减振效果。     

油脂对红壤结构性质与水流运动特征的影响

本文通过室内灌水入渗试验,研究了灌溉水油脂浓度（0,1.0,3.0和10.0g/L）、灌水频率（1d1次,2d1次,4d1次）和灌溉模式（纯清水灌溉,纯含油脂灌溉水灌溉,含油脂灌溉水-清水交替灌溉）对受灌土壤结构性质与水流运动特征的影响.结果显示,随灌水进入到受灌土壤中的油脂主要集中在优先流通道中快速运动,优先流湿润锋处的土壤油脂浓度较高且不受灌溉水中油脂浓度的影响,表明即便是采用较低油脂浓度的灌溉水灌溉,依然对地下水系统存在较高的污染风险;高频率、低定额的含油脂灌溉水灌溉有利于进入到受灌土壤中的油脂向深层土壤运动,使得斥水性土层厚度增大,从而导致入渗水流运动的不确定性及地下水系统的污染风险均增大;油脂对受灌土壤团聚体的再团聚作用只有在其浓度较高时才能形成,含油脂灌溉水-清水交替灌溉因降低了受灌土壤的油脂浓度反而导致土壤团聚体分散和破碎.研究成果对再生水和原污水农田灌溉制度设计具有参考价值.     

华北地区沙尘天气垂直气溶胶直接辐射强迫

利用CALIOP数据和SBDART（Santa Barbara DISORT Atmospheric Radiative Transfer）辐射传输模式研究了2013~2016年华北地区8d沙尘天气气溶胶及其直接辐射强迫垂直分布特征,分析了气溶胶垂直分布和光学特性对直接辐射强迫的影响.结果表明,气溶胶集中分布在地表及以上3km范围,其中纯净沙尘型和污染沙尘型气溶胶位于上层,污染大陆型气溶胶和烟雾位于下层.大气层顶、地表和大气层的日均气溶胶直接辐射强迫分别是-38.41~-88.44,-74.03~-225.86,9.06~137.42W/m².0~8km高度范围气溶胶直接辐射强迫是负值,且随着高度的增加绝对值逐渐减小.气溶胶垂直分布对大气层顶、地表和大气层的直接辐射强迫影响较小,但对直接辐射强迫垂直分布影响较大,由气溶胶廓线差异造成的同一高度层气溶胶直接辐射强迫最大差值能达到31.18W/m².气溶胶光学厚度和单次散射反照率对直接辐射强迫影响明显.消光能力相同时,吸收性气溶胶对短波太阳光的衰减作用大于散射性气溶胶,后向散射比例大的气溶胶大于后向散射比例小的气溶胶.     

贵州农村污水典型抗生素污染水平及生态风险

抗生素残留物是一种新兴的微污染物,广泛存在于各种环境介质及生物样品中,长期暴露在抗生素环境会对人体健康、生态环境产生一定的潜在威胁。由于农村污水排放量逐渐增大、农村地区对抗生素的不合理使用以及受经济、地理地形的限制大部分农村地区都缺乏完整的污水收集管网和污水治理设施,进而导致抗生素通过多种途径进入农村环境,可能会对农村生态环境产生一定的环境风险。为了解贵州农村污水中抗生素的污染水平及处理后污水对环境的影响,作者采用固相萃取—液相色谱—串联质谱(SPE-LC-MS)联用技术,选取贵州省3处典型农村地区,对农村污水治理设施进出水中典型抗生素(包括6种磺胺类、3种四环素类、1种喹诺酮类抗生素)的浓度水平进行分析。结果表明,3处农村污水治理设施进水和出水中均检出不同程度的抗生素,浓度范围分别在ND～417.57 ng/L和ND～253.68 ng/L,其中土霉素浓度最高,进出水的浓度分别为417.57、253.68 ng/L;其次是氧氟沙星,在进出水中的最高浓度分别为278.75、183.73 ng/L。3处农村污水治理设施对抗生素的去除率在-58.32%～45.52%,对目标抗生素的去除率较低。与国内外其他地区农村污水相比,所选地区的进出水中抗生素的浓度较高。通过生态风险评估发现,经处理后的污水中均含有一种RQ≥1的抗生素物质,并且发现氧氟沙星为处理后污水中的高风险污染物,污水的排放会对环境造成一定的生态风险。