煤炭开发建设项目环境影响后评价初步研究

环境影响后评价作为环境影响评价的延伸,是提高环评有效性的有力手段,目前我国环境影响后评价仍处于起步阶段,其理论和实践都具有很强的探索性。煤炭在我国的能源地位突出,但对煤炭开采建设项目的环境影响后评价研究甚少,文章介绍了国内外环境影响后评价的研究进展,并针对煤炭项目,通过识别煤炭开采的环境影响,概述了其评价指标的选取原则、指标体系的构建和评价方法。     

基于多期遥感数据对岱海湿地的景观格局分析

文章提取了3期遥感数据的湿地类型,通过对景观格局的动态变化分析,说明了人为干扰和气候因素对岱海湿地的影响,为湿地管理提供了依据。     

FRP加固震损RC柱建模方法及骨架模型研究

为研究震损RC柱采用FRP(Fiber Reinforced Polymer,FRP)加固修复后的抗震性能,本文基于OpenSees仿真平台,根据震后RC柱的表观损伤状态提出FRP加固震损RC柱的有限元模型建立方法。对FRP加固震损RC柱进行5120种工况的Pushover分析,采用三折线荷载-位移骨架曲线,研究损伤状态对骨架曲线特征点参数的影响规律,并通过数据回归分析提出FRP加固震损RC柱的骨架曲线计算模型。分析结果表明:损伤会降低FRP加固RC柱的承载力及刚度,且降低程度随损伤指数的增大而增加,两者近似成抛物线关系;在DS-5损伤状态下,相比于FRP加固完好RC柱,FRP加固震损RC柱的屈服承载力P y、峰值承载力P c、弹性刚度K 1、弹塑性刚度K 2及下降段刚度K 3的均值下降17.9%、14.5%、41.8%、43.1%和19.9%;损伤对FRP加固RC柱弹性刚度和弹塑性刚度的降低程度明显高于屈服承载力和峰值承载力;文中提出的FRP加固震损RC柱骨架曲线计算模型具有较高精度。     

Compositions and sources of organic acids in fine particles (PM2.5) over the Pearl River Delta region, south China

Organic acids as important constituents of organic aerosols not only influence the aerosols' hygroscopic property, but also enhance the formation of new particles and secondary organic aerosols. This study reported organic acids including C14–C32fatty acids, C4–C9dicarboxylic acids and aromatic acids in PM2.5collected during winter 2009 at six typical urban, suburban and rural sites in the Pearl River Delta region. Averaged concentrations of C14–C32fatty acids, aromatic acids and C4– C9 dicarboxylic acids were 157, 72.5 and 50.7 ng/m3, respectively. They totally accounted for 1.7% of measured organic carbon. C20–C32fatty acids mainly deriving from higher plant wax showed the highest concentration at the upwind rural site with more vegetation around, while C14–C18fatty acids were more abundant at urban and suburban sites, and dicarboxylic acids and aromatic acids except 1,4-phthalic acid peaked at the downwind rural site. Succinic and azelaic acid were the most abundant among C4–C9dicarboxylic acids, and 1,2-phthalic and 1,4-phthalic acid were dominant aromatic acids. Dicarboxylic acids and aromatic acids exhibited significant mutual correlations except for 1,4-phthalic acid, which was probably primarily emitted from combustion of solid wastes containing polyethylene terephthalate plastics. Spatial patterns and correlations with typical source tracers suggested that C14–C32fatty acids were mainly primary while dicarboxylic and aromatic acids were largely secondary. Principal component analysis resolved six sources including biomass burning, natural higher plant wax, two mixed anthropogenic and two secondary sources; further multiple linear regression revealed their contributions to individual organic acids. It turned out that more than 70% of C14–C18fatty acids were attributed to anthropogenic sources, about 50%–85% of the C20–C32fatty acids were attributed to natural sources, 80%–95% of dicarboxylic acids and 1,2-phthalic acid were secondary in contrast with that 81% of 1,4-phthalic acid was primary.     

南京市黑臭河流水体中细菌多样性的研究

以南京市城南河为研究对象,分别提取上中下游的水体样本,分析水质中的氮、磷、COD等水质指标,并利用变性梯度凝胶电泳技术(DGGE)分析了城南河不同位置的细菌多样性。结果表明:城南河水体中的平均总氮为30.06 mg/L,总磷为6.14 mg/L,COD为42.03 mg/L,均超过国家V类水质标准。结合外观,城南河属于严重污染的典型黑臭河流。DGGE分析的结果表明:城南河具有较高的细菌多样性,优势菌群主要是变形菌门和拟杆菌门2大类群,且不同取样点细菌种类差别不大。     

地球化学定量预测法在武夷成矿带铜资源潜力评价中的应用

利用地球化学定量预测理论方法技术,建立了武夷成矿带紫金山铜金矿等7个典型矿床的地质-地球化学找矿模型,圈定了54处AB级预测区,并利用地球化学定量预测法分别估算了每类预测区的铜资源量,为科学评估武夷成矿带的铜矿资源潜力和该成矿带地质矿产勘察工作部署提供地球化学依据。     

光学气体成像技术在泄漏检测与维修中的应用研究

通过介绍光学气体成像技术的原理、泄漏检测与维修关键技术、甲烷气体泄漏检测与识别实验情况,讨论了该技术在石化生产过程中的应用发展趋势。     

热强化气相抽提对不同质地土壤中苯去除的影响

研究应用电阻加热强化气相抽提技术对砂土、壤土和黏土中苯去除效果的影响及作用机制.与常规抽提结果相比,在热强化处理作用下气相抽提对砂土和壤土中苯的去除效率提高了13.1%和12.3%,处理时间分别降低75%和14%.热强化处理使得黏土含水率下降,土壤渗透率升高,黏土颗粒表面羧基和乙基的吸收峰消失,有机质含量减少,苯的去除效率与对照相比提高了34%.对于砂土和壤土,热强化主要是通过促进苯在土体中扩散来提高去除效率,从而实现在较短时间内污染物质的大量去除;而对于黏土则是通过降低土壤颗粒表面有机基团的含量,从而降低污染物和土壤颗粒的吸附能力,并通过降低含水率和升高渗透率从而提高土壤中气体的扩散性能,以达到增强气相抽提效果的目的.     

硫黄联合装置停工密闭吹扫的实现

介绍了中国石化济南分公司硫黄回收联合装置安全环保停工的过程,在硫黄回收联合装置停工前,研究讨论各装置停工密闭吹扫的流程及方法,并确定各装置停工吹扫的顺序、注意事项和前期准备工作。在各装置停工吹扫过程中,严格按照停工方案,采取了分装置吹扫,该装置吹扫完毕后立即加盲板隔离,最后放火炬公用系统采取倒吹扫,实现了装置停工密闭吹扫,达到了各装置停工酸性气系统吹扫不放火炬的要求。     

基于相关性分析的PCBA热力学模型修正

目的精确且高效地对印制电路板组件热力学模型进行修正。方法采用基于拉丁超立方抽样试验设计和Speraman等级相关系数计算公式的相关性分析方法,找出电子产品热仿真试验中对元器件表面温度值影响较大的输入参数,然后进一步分析得出输入与输出之间的函数关系。在此基础上给出印制电路板组件(PCBA)热力学模型修正的一般方法流程。最后利用该方法对某航空电子产品中一块PCBA的热力学模型进行修正。结果修正结果较精确且只调用2次有限元软件。结论该热模型修正方法具有较高的精确性和高效性,可推广用于工程实践。