The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.     

Application of multivariate statistical analyses in the interpretation of geochemical behaviour of uranium in phosphatic rocks in the Red Sea,Nile Valley and Western Desert,Egypt

Factor and cluster analyses as well as the Pearson correlation coefficient have been applied to geochemical data obtained from phosphorite and phosphatic rocks of Duwi Formation exposed at the Red Sea coast. Nile Valley and Western Desert. Sixty-six samples from a total of 71 collected samples were analysed for SiO2, TiO2, Al203, Fe2O3, CaO, MgO, Na2O, K2O, P2O5, Sr, U and Pb by XRF and their mineral constituents were determined by the use of XRD techniques. In addition, the natural radioactivity of the phosphatic samples due to their uranium, thorium and potassium contents was measured by gamma-spectrometry. The uranium content in the phosphate rocks with P2O5 > 15% (average of 106.6 ppm) is higher than in rocks with P2O5 < 15% (average of 35.5 ppm). Uranium distribution is essentially controlled by the variations of P2O5 and CaO, whereas it is not related to changes in SiO2, TiO2, Al2O3, Fe2O3, MgO, Na2O and K2O concentrations.-Factor analysis and the Pearson correlation coefficient revealed that uranium belaves geochemically in different ways in the phosphatic sediments and phosphorites in the Red Sea, Nile Valley and Western Desert. In the Red Sea and Western Desert phosphorites, uranium occurs mainly in oxidized U6+ state where it seems to be fixed by the phosphate ion, forming secondary uranium phosphate minerals such as phosphuranylite. In the Nile Valley phosphorites, ionic substitution of Ca2+ by U4 is the main controlling factor in the concentration of uranium in phosphate rocks. Moreover, fixation of U6- by phosphate ion and adsorption of uranium on phosphate minerals play subordinate roles.     

Radon exhalation from building materials for decorative use

Long-term exposure to radon increases the risk of developing lung cancer. There is considerable public concern about radon exhalation from building materials and the contribution to indoor radon levels. To address this concern, radon exhalation rates were determined for 53 different samples of drywall, tile and granite available on the Canadian market for interior home decoration. The radon exhalation rates ranged from non-detectable to 312 Bq m⁻² d⁻¹. Slate tiles and granite slabs had relatively higher radon exhalation rates than other decorative materials, such as ceramic or porcelain tiles. The average radon exhalation rates were 30 Bq m⁻² d⁻¹ for slate tiles and 42 Bq m⁻² d⁻¹ for granite slabs of various types and origins. Analysis showed that even if an entire floor was covered with a material having a radon exhalation rate of 300 Bq m⁻² d⁻¹, it would contribute only 18 Bq m⁻³ to a tightly sealed house with an air exchange rate of 0.3 per hour. Generally speaking, building materials used in home decoration make no significant contribution to indoor radon for a house with adequate air exchange.     

Mode choice model for vulnerable motorcyclists in Malaysia

OBJECTIVE: In developing countries, motorcycle use has grown in popularity in the past decades. Commensurate with this growth is the increase in death and casualties among motorcyclists in these countries. One of the strategic programs to minimize this problem is to reduce motorcyclists exposure by shifting them into safer modes of transport. This study aims to explore the differences in the characteristics of bus and motorcycle users. It identifies the factors contributing to their choice of transport mode and estimates the probability that motorcyclists might change their travel mode to a safer alternative; namely, bus travel. METHODS: In this article, a survey of 535 motorcycle and bus users was conducted in seven districts of Selangor state, Malaysia. A binary logit model was developed for the two alternative modes, bus and motorcycle. RESULTS: It was found that travel time, travel cost, gender, age, and income level are significant in influencing motorcyclists' mode choice behavior. The probability of motorcycle riders shifting to public transport was also examined based on a scenario of a reduction in bus travel time and travel cost. CONCLUSIONS: Reduction of total travel time for the bus mode emerges as the most important element in a program aimed at attracting motorcyclists towards public transport and away from the motorcycle mode.     

Comparing the usability and reliability of a generic and a domain-specific medical error taxonomy

Medical error taxonomies are used to report and analyse patient safety incidents. Medical error taxonomies can be generic or domain-specific. In comparing generic and domain-specific medical error taxonomies, the literature compares the information both type of taxonomies classify. There is little evidence the taxonomies have been compared in terms of usability and reliability. Twenty nurses and 21 pharmacists participated in a study comparing the usability and reliability of a generic medical error taxonomy and a medication error taxonomy. The medical error taxonomies utilized were the Patient Safety Event Taxonomy and the NCC MERP Taxonomy of Medication Error. The study found no significant difference in the usability ratings of both taxonomies. The taxonomies required different amount of time to classify patient safety incidents and had significantly different reliability levels. The reliability of the NCC MERP Taxonomy of Medication Error was significantly different when used by nurses and pharmacists. The taxonomy was also preferred by the majority of participants. Some recommendations are made about the design of future medical error taxonomies.     

CO2 from waste to resource by developing novel mixed matrix membranes

Environmental Science and Pollution Research - Mixed matrix membranes (MMMs) were fabricated by the hydrothermal synthesis of ordered mesoporous KIT-6 type silica and incorporating in polyimide...