钢铁行业碳排放量核算方法的实证性研究

介绍了碳排放量核算的基本原理与通用方法。以某钢铁公司焦化厂CO2排放量计算为实例,对比分析了物料衡算法和经验计算法的合理性和准确性。研究发现,对于钢铁企业来说,采用IPCC方法进行CO2排放量的计算是可行的。     

PCDD/F formation during thermal desorption of chlorobenzene contaminated soil

Environmental Science and Pollution Research - Unintentional formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) is observed and investigated during the thermal desorption in...     

Combustion features under different center of heat release of a diesel engine using dimethyl carbonate/diesel blend

Experiments were performed in a single cylinder common-rail diesel engine that adopts a low temperature premixed charge compression ignition (PCCI) mode. Combustion features of dimethyl carbonate (DMC)-diesel blends under various centers of heat release (COHRs) were revealed in details. With retarding of COHR, all the peaks of pressure and pressure rise rate and bulk gas temperature are postponed and declined in sequence. Normally, the crank angle of peak pressure is quite close to the COHR, while the peak of bulk gas temperature appears about 7°CA after COHR as a rule. The prolongation can be demonstrated at every stage of combustion such as q₁₀ and q₉₀ with the COHR being put backward. In addition, the heat release of diesel is completely slower than that of D10 fuel at various stages. Unfortunately, retarding of COHR implies a declining thermal efficiency of engines as well as a higher cyclic variation in general. Nevertheless, D10 blend has higher thermal efficiency than diesel thanks to high oxygen content of DMC and low boiling point that prompts better fuel atomization and complete combustion. Meanwhile, the cyclical variation of D10 is greater than diesel fuel owing to the low heat value, high latent heat of vaporization, and poor flammability of DMC. As a total, a comprehensive understanding of PCCI combustion features under different COHRs can be conducive to conducting effective management of combustion process and manipulating the subsequent emission performance to a favorable level.     

Perfluoroalkyl substances in the Lingang hybrid constructed wetland,Tianjin, China: occurrence,distribution characteristics,and ecological risks

Environmental Science and Pollution Research - In this study, the occurrence, spatial distribution, sources, and ecological risks of perfluoroalkyl substances (PFASs) in the surface waters of the...     

N-甲基咪唑配体络合金属Cu(I)催化剂对水中2,4-二甲氧基溴苯还原脱溴

合成了以N-甲基咪唑为配体,Cu为活性中心的络合金属多相催化剂Cu(I)-NHC-SBA-15。通过1H-NMR、13CNMR、有机元素分析和FTIR对各步合成反应产物结构经行了鉴定;用SEM、N2吸附脱附等方法对催化剂进行了表征;用ICP测定了催化剂Cu含量。对催化剂催化2,4-二甲氧基溴苯还原脱溴活性进行了测试。在反应时间为24 h,通过正交实验和单因素实验,考察了催化剂用量、反应温度、还原剂用量等因素对脱溴率的影响,并确定了最佳反应条件:催化剂用量为0.05 g、水合肼用量为2 m L、反应温度为80℃,脱溴效果较好,脱溴率达到98.5%。对催化剂重复使用进行了初步研究。对催化反应动力学进行了初步研究,结果表明,该多相催化反应是由表面反应速度控制,并符合一级动力学反应。对反应机理进行了初步探讨。     

二氧化碳回收技术进展

CO2的过量排放对全球的气候变暖有着不可推卸的责任,同时CO2又是一种重要的碳资源,对它的回收和利用将具有很大的经济效益和社会效益。CO2回收的方法主要是膜吸收法、变压吸附法、化学吸收法和低温分离法,特别是离子液体对CO2的吸收,为CO2的减排提供了良好的手段。     

Bt肠毒素基因与plcR基因的相关性及肠毒素对小鼠的急性毒性

用PCR方法检测溶血肠毒素BL、肠毒素T和肠毒素S三种肠毒素基因(hblA、becT、entS)及毒素调控基因plcR在30株苏云金芽胞杆菌株(Bt)中的分布.结果表明,含有hblA基因、entS基因、becT基因及plcR基因片段的Bt菌株分别占66.7%、70%、70%和73.3%.其中,含有plcR基因的菌株都至少含有一种肠毒素基因,不含肠毒素基因的菌株也未检测到plcR基因,说明plcR基因与肠毒素基因有着密切的关系.用3个Bt菌株WB9、HD2和HD9(都含有hblA、becT、entS和plcR基因片段,HD2和HD9经RPLA与TECRA肠毒素检测试剂盒检测具有高滴度)对小白鼠进行口服急性毒性试验.结果表明,所有3种供试菌株的发酵上清液对小白鼠行为和健康没有明显影响,对内部器官(心、肝、肺等)也没有产生病理现象.图5表3参14     

Examining the technology acceptance for dismantling of waste printed circuit boards in light of recycling and environmental concerns

The dismantling of printed circuit board assemblies (PCBAs) and the recovery of their useful materials can lead to serious environmental impacts mainly due to their complicated physical structure and the variety of toxic elements contained in their material composition. So far, less attention has been paid to their responsible recycling compared to that of bare printed circuit boards. Combined with other materials recovery process, proper dismantling of PCBAs is beneficial to conserve scarce resources, reuse the components, and eliminate or safely dispose of hazardous materials. In analyzing the generation, resources potential and hazardous risk of scrap PCBAs, technologies used for the dismantling of waste PCBAs have been widely investigated and reviewed from the aspects of both industrial application and laboratory-scale studies. In addition, the feasibility of PCBA dismantling has been discussed, the determinants of which, including the heating conditions and mechanical properties have been identified. Moreover, this paper evaluates the environmental consequences caused by the dismantling of PCBAs.     

近20年中国粮食生产变化特征及其对区域粮食供需格局的影响

中国是一个农业大国,用占世界不到9%的耕地养活了占世界近20%的人口。国家及区域尺度粮食安全问题一直备受关注。以省为研究单元,借助GIS空间分析与统计工具,分析了1999—2018年中国粮食生产变化的总体特征、地域格局演变特征及这些变化对区域粮食供需格局的影响。研究结果表明：全国粮食总产量呈现显著增加的趋势,增长率为0.11亿t/年。北方粮食总产量呈显著增长趋势,而南方粮食总产量基本维持稳定。玉米产量的增加对这些变化起到了主导作用。在省域尺度上,近20年五种主要粮食作物（稻谷、小麦、玉米、豆类和薯类）产量时空变化具有较大差异。粮食产量的变化对区域粮食供需格局产生了较大影响。特别是东南沿海地区的广东、浙江、福建三省,从稻谷和小麦两大口粮供过于求型变为了供给不足型省份。但在全国尺度上,人均粮食占有量在Y 1999—2003时段（1999—2003年五年平均情况）和Y 2014—2018时段（2014—2018年五年平均情况）分别为368.0 kg/人和461.5 kg/人;人均两大口粮占有量在Y 1999—2003时段和Y 2014—2018时段分别为220.3 kg/人和247.6 kg/人。播种面积的变化是全国及区域尺度上粮食作物产量变化的直接原因。但其根本原因则更多归因于土地利用价值驱动的属性、功能及质量的变化。此外,根据导致耕地减少的四种主要类型——“非农化”“非粮化”“荒废化”和“生态化”,探讨了其形成原因并提出相应的提高区域粮食生产的对策建议,以期对区域粮食种植格局调整及实现两大口粮需求省份向自给型省份转型提供参考。