An Evaluation of the Semi-VOST Method for Determining Emissions from Hazardous Waste Incinerators

The Semi-Volatile Organic Sampling Train method was investigated to determine its reliability and to determine the bias and precision of the method when used to determine emissions from hazardous waste incinerators. Experiments showed that the matrix and sampling variables usually involved in sampling emissions from a hazardous waste incinerator had no significant effect on the recovery of 11 different organic compounds. Significant losses of the sampled compounds can occur during sample preparation. The degree of loss appears to be directly related to the compounds, vapor pressure. These losses can be corrected for by adding deuterated surrogates to the sample and analyzing the surrogates along with the native compounds.

The bias determination was based on dynamic spiking of the sampling train with five deuterated organic compounds selected from Appendix VIII of the Resource Conservation and Recovery Act regulations. The results show biases of from -1 ± 8 percent to -18 ± 27 percent for chlorinated and nonchlorinated compounds. Pyridine, a water-soluble compound, showed a larger bias of-29 ± 13 percent. Particular attention to the recovery of water soluble compounds is necessary to minimize bias in their determinations. Further work is needed to determine the reliability of laboratory-determined retention volumes that are used to determine sampling conditions.     

Predicting and Managing the Health Risks of Sour-Gas Wells

The development of sour-gas resources in Canada and the United States has prompted concerns about the public health risks of accidental releases of gas contaminated with hydrogen sulfide (H₂S) from wells. This paper focuses on methods for improving the prediction and management of those risks. Data associated with the health effects of hydrogen sulfide are examined, and it is suggested that sublethal effects should be addressed in risk assessments of sour-gas wells along with the life-threatening effects normally considered. The demarcation of hazard zones around wells can be improved by using a statistical approach for estimating an upper-bound H₂S release rate; this rate can then be used in an atmospheric dispersion model to estimate maximum distances to downwind concentrations for lethal (300 ppmv) and sublethal (50 ppmv) effects resulting from an accidental release. A vertical release is found to have little impact, especially under stable atmospheric conditions; horizontal releases, on the other hand, result in the greatest downwind distances for health impacts. Management of health risks depends on a mix of safety technologies and contingency actions, such as well-ignition options and provision for post-release monitoring and assessment of ambient H₂S concentrations.     

Addressing Public Fears Related to the Siting of Hazardous Waste Facilities

Recent catastrophic industrial accidents have left the public wary of most industrial facilities. Fearing illness and death from toxic releases, the public has opposed siting hazardous waste facilities in their locale. Associated with these concerns are fears of declining property values and a perceived reduction in the quality of life for a community. Recent political actions stemming from these fears have made siting these facilities an extremely unpopular and expensive process.

This paper presents a systematic, phased approach for performing a reliability and hazards analysis of a hazardous waste facility design. It also demonstrates how the results of a risk analysis can present an accurate "risk picture" of the facility for use in alleviating public fears. A typical analysis is outlined and methods that can be used to convey to the public the results of this type of risk analysis are explored.     

Removal of Volatile Aliphatic Hydrocarbons in a Soil Bioreactor

Soil removal of propane, isobutane and n-butane from a waste air stream was evaluated in the laboratory and in a prototype soil bioreactor. Laboratory investigations indicated first-order kinetics and the potential to degrade light aliphatic hydrocarbons and trichlorethylene, a compound ordinarily resistant to aerobic biological treatment. The predicted behavior of the bioreactor, based on laboratory studies, agreed closely with the actual behavior of the Reid system. The prototype bioreactor reduced the hydrocarbon concentrations in the air by at least 90percent with a residence time of 15 minutes and a pressure drop of 85 cm of water. The bioreactor functioned well through a range of temperatures, 12°C to 24°C.     

A Study of Ammonia Source at a Portland Cement Production Plant

A source and process sampling study was conducted at a dry process Portland Cement production plant. The study was performed to determine the nature of the formation of a highly visable plume related to the kiln emissions. One aspect of the study focused on the source or point of NH₃ within the production process. An extensive number of process solids from raw feeds to baghouse solids were collected and analyzed for NH₄ ⁺. Samples were analyzed for NH₄ ⁺ both by washing the solids with 0.1 N H₂SO₄ and by collecting NH₃ in impingers as it was evolved from heated solids. The results showed that NH₄ ⁺ was present in many process samples and that the collection efficiency of NH₄ ⁺ in the baghouse was related to baghouse temperature. The data also showed that NH₃ was derived from the shale used in the raw feed at this cement production plant.     

The Effects of Infiltration and Insulation on the Source Strengths and Indoor Air Pollution from Combustion Space Heating Appliances

Many energy conservation strategies for residences involve reducing house air exchange rates. Reducing the air exchange rate of a house can cause an increase in pollutant levels if there is an indoor pollution source and if the indoor pollutant source strength remains constant. However, if the indoor pollutant source strength can also be reduced, then it is possible to maintain or even improve indoor air quality. Increasing the insulation level of a house is a means of achieving energy conservation goals and, in addition, can reduce the need for space heating and thereby reduce the pollutant source strengths of combustion space heaters such as unvented kerosene space heaters, unvented gas space heaters, and wood stoves. In this paper, the indoor air quality trade-off between reduced infiltration and increased insulation in residences is investigated for combustion space heaters. Two similar residences were used for the experiment. One residence was used as a control and the other residence had infiltration and insulation levels modified. An unvented propane space heater was used as the source in this study. A model was developed to describe the dependence of both indoor air pollution levels and the appliance source strengths on house air exchange rates and house insulation levels. Model parameters were estimated by applying regression techniques to the data. Results show that indoor air pollution levels in houses with indoor combustion space heating pollution sources can be held constant (or lowered) by reducing the thermal conductance by an amount proportional to (or greater than) the reduction of the air exchange rate.     

Low NOx,High Efficiency Multistaged Burner: Fuel Oil Results

A multistaged combustion burner designed for in-furnace NO_x control and high combustion efficiency is being evaluated for high nitrogen content fuel and waste incineration application in a 0.6 MW package boiler simulator. A low NO_x precombustion chamber burner has been reduced in size by approximately a factor of two (from 600 to 250 ms first-stage residence time) and coupled with (1) air staging, resulting in a three-stage configuration, and (2) natural gas fuel staging, yielding up to four stolchlometric zones. Natural gas, doped with ammonia to yield a 5.8 percent fuel nitrogen content, and distillate fuel oil, doped with pyridine to yield a 2 percent fuel nitrogen content, were used to simulate high nitrogen content fuel/waste mixtures. The multistaged burner reduced NO emissions by 85 percent from emission levels from a conventional unstaged burner mounted on a commercial package bollerTA minimum NO emission level of 110 ppm was achieved in the fuel oil tests, from a level of 765 ppm for conventional firing. This is compared with a 160 ppm minimum NO level achieved in gaseous fuel tests, from an uncontrolled level of 1000 ppm. Boiler fuel staging, or reburnlng, appears to be superior to air staging for high combustion efficiency due to its minimal fuel-rich core and second flame front in the boiler.     

Speciation of Arsenic in Ambient Aerosols Collected in Los Angeles

First-time measurements of the potentially toxic inorganic species of arsenic (arsenite arid arsenate) have been obtained in fine (<2.5 µm AD) and coarse (>2.5 µm AD) atmospheric particles in the Los Angeles area. A recently developed method that includes procedures for sample collection, preparation, and analysis was used in this study. Size-fractlonated aerosol samples were collected with a high-volume dichotomous virtual impactor that employed polytetrafluoroethylene filters. Results were obtained for the recovery of arsenic standards added to unexposed and collected filters. Data from this study, indicated that the recently developed speciation method can be used to determine concentrations of As(lll) and As(V) In atmospheric particulate matter samples.

Size-fractionated aerosol samples were collected in the city of Industry during January and February 1987. In most samples, As(lll) and As( V) were above the detection limit (approximately 1 ng m^-3 of either species) in both aerosol size fractions. A greater portion (about 75 percent) of the two species were observed in the fine particles. The As(lll)/As(V) ratio for both particle sizes was close to 1 (I.e., an equal mixture of both species). Comparison of total suspended particulate arsenic measured by the speciation method to that measured by a routine California Air Resources Board-approved procedure showed good agreement (r = 0.94), indicating both methods were approximately equivalent for the collection and analysis of aerosol arsenic.     

Evaluating Sources of Indoor Air Pollution

Evaluation of Indoor air pollution problems requires an understanding of the relationship between sources, air movement, and outdoor air exchange. Research is underway to investigate these relationships. A three-phase program is being implemented: 1) Environmental chambers are used to provide source emission factors for specific indoor pollutants; 2) An IAQ (Indoor Air Quality) model has been developed to calculate indoor pollutant concentrations based on chamber emissions data and the air exchange and air movement within the indoor environment; and 3) An IAQ test house is used to conduct experiments to evaluate the model results. Examples are provided to show how this coordinated approach can be used to evaluate specific sources of indoor air pollution. Two sources are examined: 1) para-dichlorobenzene emissions from solid moth repellant; and 2) particle emissions from unvented kerosene heaters.

The evaluation process for both sources followed the three-phase approach discussed above. Para-dichlorobenzene emission factors were determined by small chamber testing at EPA’s Air and Energy Engineering Research Laboratory. Particle emission factors for the kerosene heaters were developed In large chambers at the J. B. Pierce Foundation Laboratory. Both sources were subsequently evaluated in EPA’s IAQ test house. The IAQ model predictions showed good agreement with the test house measurements when appropriate values were provided for source emissions, outside air exchange, in-house air movement, and deposition on “sink” surfaces.