软土地区高墩梁桥抗震支座选型及横向约束构造研究∗

为了研究软土地区地震作用下高墩先简支后桥面连续梁桥的支座选型及横桥向抗震约束问题,选取了普通板式橡胶支座、钢阻尼滑板支座、LNR 橡胶支座和 HDR 高阻尼支座四种支座类型,以软土地区某(4×30)m 跨径高墩先简支后桥面连续梁桥为例,进行了延性抗震体系和减隔震体系抗震设计对比以及设置挡块的横桥向抗震约束效果研究。结果表明：软土地区高墩先简支后桥面连续梁桥墩柱配筋率主要由 E1 地震作用下墩底截面偏心受压检算工况决定,采用减隔震体系并不能降低桥墩配筋率。通过对采用四种不同支座桥梁的内力、墩梁相对位移以及配筋率方面综合分析可知,软土地区高墩先简支后桥面连续梁桥的周期较长,这类桥梁抗震关键问题是防止落梁、减小墩顶位移。采用普通板式橡胶支座并合理的设计纵横向防落梁装置的延性抗震体系更适宜于软土地区高墩梁式桥,合理设计抗震挡块可以起到很好的横向约束作用,避免横向落梁的发生。     

生物炭添加和灌溉对温室番茄地土壤反硝化损失的影响

生物炭添加和灌溉是番茄地常用的田间管理措施,然而其对反硝化的影响还不清楚.本研究种植试验设置3个灌溉量水平分别为估算作物生育期需水量ET0的50%(W50%)、75%(W75%)、100%(W100%)和3个生物炭添加水平分别为B0(折合纯碳,0)、B25(折合纯碳,25 t·hm-2)、B50(折合纯碳,50 t·hm-2),在2014年和2015年番茄收获后,每个试验小区采集具有代表性的土样进行室内培养试验,采用乙炔抑制法来研究土壤的反硝化损失和不加乙炔研究N_2O的排放量.结果表明生物炭和灌溉量显著改变了土壤的理化性质.与B0相比,添加生物炭能够提高土壤全碳、全氮含量和pH值,降低铵态氮、硝态氮含量,而灌水量降低了土壤中全氮和全碳的含量.因此,与B0/W50%相比,B25/W75%和B50/W100%处理显著减少了反硝化损失量(P0.05).生物炭和灌溉量的交互作用对土壤无机氮含量和反硝化损失的影响均达到显著水平(P0.05),且对硝态氮的影响表现为灌溉量生物炭添加量两者交互作用,对铵态氮的影响表现为生物炭添加量灌溉量两者交互作用,对反硝化损失的影响表现为灌溉量生物炭添加量两者交互作用.反硝化损失量与土壤中无机氮含量、(CO_2-C)矿化量与N_2O排放量均呈正相关关系.不同生物炭添加量和灌溉量处理后明显影响了N_2O/DN(P0.05),培养结束时,各处理下的N_2O累积排放量/DN累积排放量差异较大,介于0.31%~1.88%.     

Expression of sulfur uptake assimilation-related genes in response to cadmium, bensulfuron-methyl and their co-contamination in rice roots

The responses of sulfur （S） uptake assimilation-related genes＇ expression in roots of two rice cultivars to cadmium （Cd）, bensulfuron-methyl （BSM） and their co-contamination （Cd＋BSM） were investigated by gene-chip microarray analysis and quantitative real-time PCR （QRT-PCR） technology. Treatments of Cd and Cd＋BSM induced expression of sulfate transporter and permease genes, and promoted sulfate uptake in rice roots. Cd＋BSM could alleviate Cd toxicity to cv. Fengmeizhan seedlings, probably due to Cd＋BSM promoting greater S absorption by seedlings. Cd and Cd＋BSM induced expression of sulfate assimilation-related genes, and thus activated the sulfur assimilation pathway. Cd and Cd＋BSM induced expression of phytochelatin synthase and metallothionein genes, and induced expression of glutathione S-transferases （GSTs）, glutathione synthase （GS） and S- containing antioxidation enzyme genes, which detoxified Cd2＋. It is suggested that （to cope with the toxicity of Cd, BSM and their co-contamination） the S uptake and assimilation pathway was activated in rice roots by increased expression of related genes, thus enhancing the supply of organic S for synthesis of Cd or BSM resistance-related substances.     

Comparison of quartz sand, anthracite, shale and biological ceramsite for adsorptive removal of phosphorus from aqueous solution

The choice of substrates with high phosphorus adsorption capacity is vital for sustainable phosphorus removal from waste water in constructed wetlands. In this study, four substrates were used： quartz sand, anthracite, shale and biological ceramsite. These substrate samples were characterized by X- ray diffractometry and scanning electron microscopy studies for their mineral components （chemical components） and surface characteristics. The dynamic experimental results revealed the following ranking order for total phosphorus （TP） removal efficiency： anthracite 〉 biological ceramsite 〉 shale 〉 quartz sand. The adsorptive removal capacities for TP using anthracite, biological ceramsite, shale and quartz sand were 85.87, 81.44, 59.65, and 55.98 mg/kg, respectively. Phosphorus desorption was also studied to analyze the substrates＇ adsorption efficiency in wastewater treatment as well as the substrates＇ ability to be reused for treatment. It was noted that the removal performance for the different forms of phosphorus was dependent on the nature of the substrate and the adsorption mechanism. A comparative analysis showed that the removal of particulate phosphorus was much easier using shale. Whereas anthracite had the highest soluble reactive phosphorus （SRP） adsorptive capacity, biological ceramsite had the highest dissolved organic phosphorus （DOP） removal capacity. Phosphorus removal by shale and biological ceramsite was mainly through chemical adsorption, precipitation or biological adsorption. On the other hand, phosphorus removal through physical adsorption （electrostatic attraction or ion exchange） was dominant in anthracite and quartz sand.     

Enhanced struvite recovery from wastewater using a novel cone-inserted fluidized bed reactor

The feasibility of struvite recovery at low （12.5 mg/L） and high （120 mg[L） phosphorus concentrations was studied by constructing a novel fluidized bed reactor with cones （FBRwc） and without cones （FBRwoc）. The crystallization process was continuously operated for 133 days under different hydraulic retention times （HRT = 1-10 hr）, pH （7.5-10）, and molar ratios of Mg/P （0.75-1.75）, N/P （1-10） and Ca/Mg （0-2）. The optimum operating conditions of HRT, pH, Mg/P and N/P molar ratios were found to be 2 hr, 9, 1.25, and 7.5, respectively. Under these optimum conditions, the phosphorus precipitation efficiencies of FBRwc were 93% for low and 98% for high phosphorus influent; however, the efficiencies were 78% and 81% for FBRwoc, respectively. Due to crystal losses at each junction （17%-31%）, the crystal recovery efficiency of FBRwoc was relatively low （47%-65%） for both influent concentrations. However, the losses were minimal in FBRwc, which showed 75% and 92% crystal recovery for low and high phosphorus concentrations, respectively. At low calcium concentration, crystal chemical analysis showed the product to be pure struvite （〉 99%）. The scanning electron microscope and X-ray diffraction results further confirmed that the crystal recovered from FBRwc contained pure struvite, which could be considered a high quality fertilizer. Except HRT, all parameters （pH, Mg/P, N/P and Ca/Mg） were found to be influencing factors for FBRwc performance. Overall, inserting cones in each part of the reactor played a significant role in enhancing struvite recovery from a wide range of phosphorus-containing wastewater.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Origin of major ions in monthly rainfall events at the Bamenda Highlands, North West Cameroon

Rainwater characteristics can reveal emissions from various anthropogenic and natural sources into the atmosphere. The physico-chemical characteristics of 44 monthly rainfall events （collected between January and December 2012） from 4 weather stations （Bamenda, Ndop plain, Ndawara and Kumbo） in the Bamenda Highlands （BH） were investigated. The purpose was to determine the sources of chemical species, their seasonal inputs and suitability of the rainwater for drinking. The mean pH of 5 indicated the slightly acidic nature of the rainwater. Average total dissolved solids （TDS） were low （6.7 mg/L）, characteristic of unpolluted atmospheric moisture/air. Major ion concentrations （mg/L） were low and in the order K＋ 〉 Ca2＋ 〉 Mg2~ 〉 Na＋ for cations and NO3 〉〉 HCO3 〉 SO] 〉 CI- 〉 PO3- 〉 F- for anions. The average rainwater in the area was mixed Ca-Mg-SO4-CI water type. The CI-/Na＋ ratio （1.04） was comparable to that of seawater （1.16）, an indication that N a＋ and CI originated mainly from marine （Atlantic Ocean） aerosols. High enrichments of Ca2＋, Mg2＋ and SO2- to Na＋ ratios relative to seawater ratios （constituting 44% of the total ions） demonstrated their terrigenous origin, mainly from Saharan and Sahelian arid dusts. The K＋/Na＋ ratio （2.24）, which was similar to tropical vegetation ash （2.38）, and NO3 was essentially from biomass burning. Light （〈 100 mm） pre-monsoon and post-monsoon convective rains were enriched in major ions than the heavy （〉 100 mm） monsoon rains, indicating a high contribution of major ions during the low convective showers. Despite the acidic nature, the TDS and major ion concentrations classified the rainwater as potable based on the WHO guidelines.     

Evaluation of soil washing process with carboxymethyl-β-cyclodextrin and carboxymethyl chitosan for recovery of PAHs/heavy metals/fluorine from metallurgic plant site

Polycyclic aromatic hydrocarbons(PAHs)/heavy metals/fluorine(F) mixed-contaminated sites caused by abandoned metallurgic plants are receiving wide attention. To address the associated environmental problems,this study was initiated to investigate the feasibility of using carboxymethyl-β-cyclodextrin(CMCD) and carboxymethyl chitosan(CMC) solution to enhance ex situ soil washing for extracting mixed contaminants. Further,Tenax extraction method was combined with a first-three-compartment model to evaluate the environmental risk of residual PAHs in washed soil. In addition,the redistribution of heavy metals/F after decontamination was also estimated using a sequential extraction procedure. Three successive washing cycles using50 g/L CMCD and 5 g/L CMC solution were effective to remove 94.3% of total PAHs,93.2% of Pb,85.8% of Cd,93.4% of Cr,83.2% of Ni and 97.3% of F simultaneously. After the 3rd washing,the residual PAHs mainly existed as very slowly desorbing fractions,which were in the form of well-aged,well-sequestered compounds; while the remaining Pb,Cd,Cr,Ni and F mainly existed as Fe–Mn oxide and residual fractions,which were always present in stable mineral forms or bound to non-labile soil fractions. Therefore,this combined cleanup strategy proved to be effective and environmentally friendly.     

胡敏酸改性膨润土钝化污染土壤Pb&Cd及机理

通过盆栽试验,探讨了胡敏酸改性膨润土对重金属铅、镉污染土壤的钝化效果及机理。结果表明,铅、镉污染土壤中施加胡敏酸改性膨润土能显著降低小白菜中Pb、Cd的含量,在添加Cd(3 mg/kg)/Pb(250 mg/kg)污染土壤和Cd(1 0 mg/kg)/Pb(5 00 mg/kg)污染土壤上小白菜地上部分Pb含量分别比对照降低19.08%和47.91%,Cd含量分别比对照降低9.79%和14.89%。土壤本身对添加的重金属Pb/Cd有一定的耐受力和自我净化能力,在添加重金属后,添加的Pb/Cd元素大部分直接转化为较为稳定的碳酸盐结合态和铁锰氧化结合态。相关性分析显示小白菜的鲜重与小白菜Pb/Cd含量极显著负相关,进一步说明胡敏酸改性膨润土是通过提高小白菜的生物量,从而降低Pb/Cd在小白菜中的含量。     

便携β射线法手工监测PM_(2.5)的可行性研究

提出利用自动射线原理结合重量法的简捷便携特点的便携射线仪手工监测PM2.5的思路,平行比对了便携射线法和手工重量法所测60组PM2.5浓度的监测结果,采用线性回归及T检验、F检验等理论分析了两者数据结果间的有效性和可比性。结果表明,便携式射线仪监测结果与重量法监测结果之间有效可比且得到了两者间的线性回归方程;此外进行了20组数据的实样验证,换算值和真值之间相对误差在8%以内,因而确定了便携射线仪手工监测PM2.5的可行性。