A three-layer diffusion-cell to examine bio-enhanced dissolution of chloroethene dense non-aqueous phase liquid

Microbial reductive dechlorination of trichloroethene (TCE) and perchloroethene (PCE) in the vicinity of their dense non-aqueous phase liquid (DNAPL) has been shown to accelerate DNAPL dissolution. A three-layer diffusion-cell was developed to quantify this bio-enhanced dissolution and to measure the conditions near the DNAPL interface. The 12 cm long diffusion-cell setup consists of a 5.5 cm central porous layer (sand), a lower 3.5 cm DNAPL layer and a top 3 cm water layer. The water layer is frequently refreshed to remove chloroethenes at the upper boundary of the porous layer, while the DNAPL layer maintains the saturated chloroethene concentration at the lower boundary. Two abiotic and two biotic diffusion-cells with TCE DNAPL were tested. In the abiotic diffusion-cells, a linear steady state TCE concentration profile between the DNAPL and the water layer developed beyond 21 d. In the biotic diffusion-cells, TCE was completely converted into cis-dichloroethene (cis-DCE) at 2.5 cm distance of the DNAPL. Dechlorination was likely inhibited up to a distance of 1.5 cm from the DNAPL, as in this part the TCE concentration exceeded the culture’s maximum tolerable concentration (2.5 mM). The DNAPL dissolution fluxes were calculated from the TCE concentration gradient, measured at the interface of the DNAPL layer and the porous layer. Biotic fluxes were a factor 2.4 (standard deviation 0.2) larger than abiotic dissolution fluxes. This diffusion-cell setup can be used to study the factors affecting the bio-enhanced dissolution of DNAPL and to assess bioaugmentation, pH buffer addition and donor delivery strategies for source zones.     

Chitosan/albumin/CaCO3 as mimics for membrane bioreactor fouling: genesis of structural mineralized-EPS-building blocks and cake layer compressibility

Membrane bioreactor biofouling is usually described as an extracellular matrix in which biopolymers, inorganic salts and active microbes co-exist. For that reason, biomineralization (BM) models can be useful to describe the spatial organization and environmental constraints within the referred scenario. BM arguments were utilized as background in order to (1) evaluate CaCO₃ influence on flux decline; pore blocking and cake layer properties (resistance, permeability and compressibility) in a wide range of Chitosan/Bovine serum albumin (BSA) mixtures during step-pressure runs and, (2) perform membrane autopsies in order to explore the genesis of mineralized extracellular building blocks (MEBB) during cake layer build up. Using low molecular weight chitosan (LC) and BSA, 2 L of 5 LC/BSA mixtures (0.25-1.85 ratio) were pumped to an external ultra filtration (UF) membrane (23.5 cm², hydrophobic, piezoelectric, 100 kDa as molecular weight cut-off). Eight different pressure steps (40 ± 7 to 540 ± 21 kPa) were applied. Each pressure step was held for 900 s. CaCO₃ was added to LC/BSA mixtures at 0.5, 1.5 and 3 mM in order to create MEBB during the filtration tests. Membrane autopsies were performed after the filtration tests using thermo gravimetric, scanning microscopy and specific membrane mass (mg cm⁻²) analyses. Biopolymer-CaCO₃ step-pressure filtration created compressible cake layers (with inner voids). The formation of an internal skeleton of MEBB may contribute to irreversible fouling consolidation. A hypothesis for MEBB genesis and development was set forth.     

Comparing the sensitivity of soil invertebrates to pesticides with that of Eisenia fetida

The sole routine testing of the standard earthworm Eisenia fetida for the terrestrial risk assessment of pesticides has been under much debate since other soil invertebrates may be more sensitive than this standard test species. However, the very low availability of laboratory toxicity data for taxa other than E. fetida has greatly hampered sensitivity comparisons. In the present study, the relative tolerance (T_rel) approach was used to enable comparing toxicity thresholds obtained from the US-EPA ECOTOX database, for main terrestrial taxonomic groups and pesticidal types of action (insecticides, fungicides, herbicides, and other) separately. Analyses confirmed previously reported lower and higher sensitivity of collembolans to fungicides and insecticides, respectively. However, various other discrepancies in susceptibility relative to E. fetida were encountered as indicated by species sensitivity distributions and/or calculated 95% confidence intervals of T_rel values. Arachnids and isopods were found to be more sensitive to insecticides, and nematodes to fungicides, as compared to E. fetida. Implications of study findings for the terrestrial risk assessment of pesticides are discussed.     

Percolation and batch leaching tests to assess release of inorganic pollutants from municipal solid waste incinerator residues

In this study, percolation and batch leaching tests were considered in order to characterize the behaviour of air pollution control (APC) residues produced in a municipal solid waste incinerator (MSWI) as a function of the liquid to solid ratio (L/S). This waste is hazardous, and taking into account their physical and chemical properties, leaching of contaminants into the environment is the main concern. In our work the leaching behaviour of toxic heavy metals (Pb, Zn, Cr, Ni and Cu) and inorganics associated with soluble salts (Na, K, Ca and Cl) was addressed. Although pH of the leaching solution is the most important variable, L/S may also play an important role in leaching processes. In our work, results from column and batch tests were compared in terms of concentration (mg/L) and releasing (mg/kg). The APC residues revealed to be hazardous according to both tests, and both Pb and Cl⁻ far exceeded the regulatory thresholds. The material exhibits high solubility, and when the liquid to solid ratio was high, more than 50% can be solubilised. The patterns of release may be in some cases availability or solubility controlled, and the former was easier to identify. When the results from column and batch experiments were compared by representing the cumulative released amounts (in mg/kg) as a function of L/S, both curves match for Zn, Ni, Cu, K, Na, Cl and Ca, but for Cr and Pb a significant difference was observed. In fact, the column experiments revealed that under percolation conditions it should be expected slow releasing of Pb along time. From this study, it can be concluded that the released amounts obtained in batch experiments for a certain L/S should be considered as the worst case for medium term. Some simple models proposed on the literature and based on local equilibrium assumption showed good fitting to experimental data for soluble species (non-reactive solutes).     

Trace elements and microbiological parameters in farmed Nile tilapia with emphasis on muscle,water, sediment and feed

Fish may bioaccumulate contaminants from the aquatic environment and extend them to the food chain provoking risks to human health. This study evaluated the microbiological parameters of the pond´s water and trace elements concentrations in samples of water, sediment, feed and muscle of farmed Nile tilapia used for human consumption in southern Brazil. A total of 240 fish were collected from 12 tilapia farms. Sediment, tank water and dry ration used in the animals' diet were collected for analysis. Analysis were performed by Energy Dispersion X-ray Fluorescence (EDXRF), Inductively Coupled Plasma Mass Spectrometer (ICP-MS), Induced Coupled Plasma Optical Emission Spectrometer (ICP-OES), and Atomic Absorption Spectrometer (AAS-VGA). In addition, the microbiological analysis of the water was carried out. The concentrations of Se, I, Fe, Cu and Zn in fish muscle were higher than the recommended by the Brazilian legislation, considering the advised daily intake for adults. The arsenic element had concentrations above the limit stipulated by the present Brazilian legislation, observed in all samples of muscle, sediment and tank water highlighting a possible environmental and fish contamination by the toxic element. Moreover, the arsenic concentration in the water presented a positive correlation (ρ?=?0.33) with arsenic in the muscle, suggesting that tilapia is a good environmental bioindicator, once they properly reflect the levels of arsenic in the water. It is suggested to perform an arsenic speciation for quantification of the inorganic form and accurate assessment of the degree of toxicity in the muscle samples and risks it can bring to human health. Regarding the other potentially toxic elements (Hg, Pb and Cd), and microbiological analysis of water it was verified that the consumption of the fish in question does not raise risks, since the values are within a quality benchmark established by law. The concentration of total and fecal coliforms in pond´s water in the facilities was in agreement with the microbiological indexes required by the legislation of CONAMA class II. Western region presented the lowest concentrations of fecal coliforms when compared to the other regions. There was no significant difference in the microbiological counts of total heterotrophic bacteria, Vibrio spp. and Pseudomonas spp. among the regions.     

Forecasting model to assess the potential of secondary lead production from lead acid battery scrap

Environmental Science and Pollution Research - Lead acid battery (LAB) scrap management is an important issue both environmentally and economically. The recovery of lead from battery scrap leads to...     

Synthesis of functionalized mesoporous material from rice husk ash and its application in the removal of the polycyclic aromatic hydrocarbons

Environmental Science and Pollution Research - The rice husk ash (RHA) was used as an alternative source of silica for the synthesis of the functionalized mesoporous material, which was used in the...     

In situ chemical oxidation: Lessons learned at multiple sites

This paper compiles a detailed set of in situ chemical oxidation (ISCO) lessons learned pertaining to design, execution, and safety based on global experiences over the last 20 years. While the benefits of a “correct” application are known (e.g., cost effectiveness, speed, permanence of treatment), history also provides examples of a variety of “incorrect” applications. These provide an opportunity to highlight recurring themes that resulted in failures. ISCO is, and will continue to provide, an important remedial tool for site remediation, particularly as a component of a multifaceted approach for addressing large and complex sites. Future success, however, requires an objective understanding of both the benefits and the limitations of the technology. The ability to learn from the mistakes of the past provides an opportunity to eliminate, or at least minimize, them in the future. Over the last 25 years of ISCO application, process understanding and knowledge have improved and evolved. This paper combines a thorough discussion of lessons learned through decades of ISCO implementation throughout all aspects of ISCO projects with an analysis of changes to the ISCO remediation market. By discussing the interplay of these two themes and providing recommendations from collective lessons learned, we hope to improve the future of safe, cost‐effective, and successful applications of ISCO.     

Removal of an anionic dye (Acid Blue 92) by coagulation–flocculation using chitosan

Chitosan (a biopolymer) is an aminopolysaccharide that can be used for the treatment of colored solutions by coagulation–flocculation (as an alternative to more conventional processes such as sorption). Acid Blue 92 (a sulfonic dye) was selected as a model dye for verifying chitosan's ability to treat textile wastewater. A preliminary experiment demonstrated that chitosan was more efficient at color removal in tap water than in demineralized water, and that a substantially lower concentration of chitosan could be used with tap water. Dye removal reached up to 99% under optimum concentration; i.e., in terms of the acidic solutions and the stoichiometric ratio between the amine groups of the biopolymer and the sulfonic groups in the dye. The flocs were recovered and the dye was efficiently removed using alkaline solutions (0.001–1 M NaOH solutions) and the biopolymer, re-dissolved in acetic acid solution, was reused in a further treatment cycle.     

Economic assessment of managing processionary moth in pine forests: a case-study in Portugal

This paper assesses the private and social profitability of current strategies for managing processionary moth (Thaumetopoea pityocampa) in Portuguese pine forests, looking at economic and environmental costs and benefits. Costs include the expenses for forest treatment and the social costs of threats to human health (dermatitis amongst others); benefits are assessed in terms of both revenue and social benefits such as carbon fixation and recreation. The evaluation was done using Cost Benefit Analysis (CBA) as an analytical framework. While this tool is currently applied to forest and environmental assessment and specific applications to pest management strategies are to be found in agricultural economics, rather few attempts have been made in the field of forest pest management. In order to assess and compare with--without options, a case-study was analysed for the Setúbal Peninsula, south of Lisbon, an area where extensive stands of maritime pine (Pinus pinaster) grow. The exercise has shown that CBA can be a valuable tool for assessing the economic and social profitability of pest management. The results demonstrate that the loss of revenues in the no-management option is not sufficient to make pest management profitable for private forest owners in the short-term. Conversely, a social profit is gained as pest management minimizes health risks for humans and avoids possible recreational losses.