The probabilistic tsunami hazard assessment along Karnataka Coast from Makran Subduction Zone,west coast of India

Coastal tsunami amplitudes were calculated to identify areas susceptible to tsunami hazard at selected locations of the coast of Karnataka, west of India, due to earthquakes in the Makran Subduction Zone. This is the first time that the probabilistic tsunami hazard assessment along this study area has been attempted. A series of earthquake source scenarios with magnitudes of Mw 8.0, Mw 8.5, and a mega thrust of Mw 9.1 were modeled by using the Community Model Interface for Tsunami interface with the MOST model of Titov and Synolakis (J. Waterway, Port, Coastal and Ocean Engineering, 121(6), 308–316, 1995). As per the previous occurrences, the two least magnitudes are probable, while Mw 9.1 is a worst-case scenario as described by Heidarzadeh et al. (Ocean Engineering, 36(5), 368–376, 2009) and the same is reported by Burbidge et al. (Geoscience Australia Professional Opinion No. 2009/11) as high magnitude. These are not at all historical earthquakes or specifically from historical catalogues. The results of modeling show that all the seven coastal locations are inundated barely in our worst-case scenario with maximum water levels in the range of 100–200 cm. The first tsunami wave strikes the coast within 4–5 h of earthquake occurrence.     

Real<Emphasis Type="Bold">-</Emphasis>time water quality monitoring using Internet of Things in SCADA

Water pollution is the root cause for many diseases in the world. It is necessary to measure water quality using sensors for prevention of water pollution. However, the related works remain the problems of communication, mobility, scalability, and accuracy. In this paper, we propose a new Supervisory Control and Data Acquisition (SCADA) system that integrates with the Internet of Things (IoT) technology for real-time water quality monitoring. It aims to determine the contamination of water, leakage in pipeline, and also automatic measure of parameters (such as temperature sensor, flow sensor, color sensor) in real time using Arduino Atmega 368 using Global System for Mobile Communication (GSM) module. The system is applied in the Tirunelveli Corporation (Metro city of Tamilnadu state, India) for automatic capturing of sensor data (pressure, pH, level, and energy sensors). SCADA system is fine-tuned with additional sensors and reduced cost. The results show that the proposed system outperforms the existing ones and produces better results. SCADA captures the real-time accurate sensor values of flow, temperature, and color and turbidity through the GSM communication.     

Use of water quality index and multivariate statistical techniques for the assessment of spatial variations in water quality of a small river

Rapid urban development has led to a critical negative impact on water bodies flowing in and around urban areas. In the present study, 25 physiochemical and biological parameters have been studied on water samples collected from the entire section of a small river originating and ending within an urban area. This study envisaged to assess the water quality status of river body and explore probable sources of pollution in the river. Weighted arithmetic water quality index (WQI) was employed to evaluate the water quality status of the river. Multivariate statistical techniques namely cluster analysis (CA) and principal component analysis (PCA) were applied to differentiate the sources of variation in water quality and to determine the cause of pollution in the river. WQI values indicated high pollution levels in the studied water body, rendering it unsuitable for any practical purpose. Cluster analysis results showed that the river samples can be divided into four groups. Use of PCA identified four important factors describing the types of pollution in the river, namely (1) mineral and nutrient pollution, (2) heavy metal pollution, (3) organic pollution, and (4) fecal contamination. The deteriorating water quality of the river was demonstrated to originate from wide sources of anthropogenic activities, especially municipal sewage discharge from unplanned housing areas, wastewater discharge from small industrial units, livestock activities, and indiscriminate dumping of solid wastes in the river. Thus, the present study effectively demonstrates the use of WQI and multivariate statistical techniques for gaining simpler and meaningful information about the water quality of a lotic water body as well as to identify of the pollution sources.     

Static and Dynamic Behavior of Fibrous Polymeric Composite Materials at Different Environmental Conditions

The study of static and dynamic behavior of environmentally conditioned fibre reinforced polymeric (FRP) composites is necessary and crucial to examine the durability, reliability and sustainability of these noble materials. FRP composites are being used all around the globe and substituting the conventional materials, starting from mini toys to large aerospace components. Present review has introduced to accumulate and understand the disseminate literature in concentrating the significance of understanding the static and dynamic behavior of FRPs with changing environmental conditionings (hygrothermal, low and high temperature, salt solution, freeze thaw, UV light) and with the interaction of different nano-fillers. Their stability and integrity in diverse service environments may be reformed by their reactions against different nature of loadings i.e. static or dynamic and the components such as fibre, matrix and fibre/matrix interfaces in those environments. The static and dynamic states of loading may come with a possible weaker region to encounter the durability and integrity of the composites. To understand the exact failure modes that correlates the position of environmentally conditioned interfaces and dynamic state of loadings, thus confusing the estimation of its overall performance and mechanical behavior. Interface reliability and durability is vital since in-service environments the degradation in the interfacial region leads to complete composite failure. Therefore, the study of combined effects of various in-service environmental conditions and the role of static and dynamic behavior on the interface will be a crucial part related to the multiaxial dynamic states of failures occurring in FRP’s.     

Model-based analysis of urban settlement process in eco-sensitive area of developing country: a study with special reference to hills of an Indian city

Rapid and unplanned expansion of a city into its eco-sensitive areas like hills, wetlands, and forests is becoming a major concern, particularly in developing countries. Understanding the process and causes of such unplanned urban expansion is of paramount importance for framing sustainable urban development policies. This paper presents a modelling concept that relates urban settlement in such eco-sensitive areas with potential socio-economic, demographic and geographical factors. The model is applied to an Indian city Guwahati, which is experiencing serious environmental degradation due to unplanned urban settlement in its eco-sensitive hilly areas. While topographical and settlement data were derived using satellite data in GIS platform, all other necessary data were collected from relevant government organizations. On validation of the multi-linear regression model, the coefficient of determination and the root mean square error are obtained as 0.938 and 1.7, respectively. Model results show that geographical parameters are less influencing as compared to the other socio-economic and demographic factors. Sensitivity analysis of urban settlements in hills of Guwahati city carried out with respect to the considered factors reveals that land value and free space availability in the surrounding area of a hill are the most sensitive parameters. This indicates that city development plans should give more importance to outward spatial expansion in plain areas with regulated land value and zoning scheme to minimize unauthorized settlement in eco-sensitive hilly areas of Guwahati city.     

Green algae of the genus Spirogyra: A potential absorbent for heavy metal from coal mine water

Algae have considerable capability for absorbing heavy metals from wastewaters and are considered an effective treatment technology. Heavy metal absorption from coal mine water from the Bhowra Abandoned mine (open cast mine) and the Sudamdih Shaft mine (underground mine waters), both located in Dhanbad, India, by cells of Spirogyra was studied at different dilutions (100 percent, 80 percent, 60 percent, 40 percent, and 20 percent). In the present study, the following 18 metals were selected for analysis: aluminium (Al), arsenic (As), silver (Ag), barium (Ba), beryllium (Be), bismuth (Bi), cadmium (Cd), cobalt (Co), chromium (Cr), cesium (Cs), copper (Cu), iron (Fe), gallium (Ga), indium (In), potassium (K), manganese (Mn), nickel (Ni), and vanadium (V). Accordingly, Al and K were found to be higher in concentration with respect to selected metals for both mine waters. The biosorption study revealed that higher amounts of Al, Bi, Co, Cs, Fe, Ga, Mn, Ni, and V were absorbed by algal biomass at 100 percent concentration from both mine waters. The maximum uptake of Cu, As, and Cd was measured at 60 percent, 40 percent, and 20 percent, respectively, for the Bhowra Abandoned mine water. The biosorption equilibrium study revealed that Ag, Al, Ba, Be, Bi, Co, Cr, Cs, Fe, Ga, In, K, Mn, Ni, and V were maximally absorbed by algal biomass at 100 percent concentration from Bhowra mine water, while the maximum uptake by the algal biomass measured for the Sudamidh coal mine water was for Al, As, Bi, Cu, Fe, and Mn at 100 percent concentration. The different physicochemical characteristics of mine water and drinking water standards was also studied. Accordingly, total dissolved solid and chemical oxygen demand concentrations exceeded the drinking water standards for water samples collected from both mines.     

Evaluation of existing equations for temporal scour depth around circular bridge piers

Scour is defined as the processes of removal of sediment particles from water stream bed by the erosive action of activated water, and also carries sediment away from the hydraulic structures. Scour is the main cause of pier failure. Numerous equations are available for estimating temporal and equilibrium scour depth. The present study describes the phenomenon of temporal scour depth variation at bridge piers and deals with the methods for its estimation. The accuracy of six temporal scour depth equations are also checked in this study. After graphical and statistical analysis, it was found that the relationship proposed by Oliveto and Hager (J Hydraul Eng (ASCE) 128(9):811–520, 2002) predicts temporal scour depth better than other equations. Three equations of equilibrium time of scour are also used for computing equilibrium time. Equilibrium time equation proposed by Choi and Choi (Water Environ J 30(1–2):14–21, 2016) gives better agreements with observed values.     

Recycling polymeric waste from electronic and automotive sectors into value added products

The environmentally sustainable disposal and recycling of ever increasing volumes of electronic waste has become a global waste management issue. The addition of up to 25% polymeric waste PCBs (printed circuit boards) as fillers in polypropylene (PP) composites was partially successful: while the tensile modulus, flexural strength and flexural modulus of composites were enhanced, the tensile and impact strengths were found to decrease. As a lowering of impact strength can significantly limit the application of PP based composites, it is necessary to incorporate impact modifying polymers such as rubbery particles in the mix. We report on a novel investigation on the simultaneous utilization of electronic and automotive rubber waste as fillers in PP composites. These composites were prepared by using 25 wt.% polymeric PCB powder, up to 9% of ethylene propylene rubber (EPR), and PP: balance. The influence of EPR on the structural, thermal, mechanical and rheological properties of PP/PCB/ EPR composites was investigated. While the addition of EPR caused the nucleation of the β crystalline phase of PP, the onset temperature for thermal degradation was found to decrease by 8%. The tensile modulus and strength decreased by 16% and 19%, respectively; and the elongation at break increased by ~71%. The impact strength showed a maximum increase of ~18% at 7 wt.%–9 wt.% EPR content. Various rheological properties were found to be well within the range of processing limits. This novel eco-friendly approach could help utilize significant amounts of polymeric electronic and automotive waste for fabricating valuable polymer composites.

Open image in new window

     

Biosorption of chromium (VI) from aqueous solutions and ANN modelling

The use of sustainable, green and biodegradable natural wastes for Cr(VI) detoxification from the contaminated wastewater is considered as a challenging issue. The present research is aimed to assess the effectiveness of seven different natural biomaterials, such as jackfruit leaf, mango leaf, onion peel, garlic peel, bamboo leaf, acid treated rubber leaf and coconut shell powder, for Cr(VI) eradication from aqueous solution by biosorption process. Characterizations were conducted using SEM, BET and FTIR spectroscopy. The effects of operating parameters, viz., pH, initial Cr(VI) ion concentration, adsorbent dosages, contact time and temperature on metal removal efficiency, were studied. The biosorption mechanism was described by the pseudo-second-order model and Langmuir isotherm model. The biosorption process was exothermic, spontaneous and chemical (except garlic peel) in nature. The sequence of adsorption capacity was mango leaf > jackfruit leaf > acid treated rubber leaf > onion peel > bamboo leaf > garlic peel > coconut shell with maximum Langmuir adsorption capacity of 35.7 mg g^?1 for mango leaf. The treated effluent can be reused. Desorption study suggested effective reuse of the adsorbents up to three cycles, and safe disposal method of the used adsorbents suggested biodegradability and sustainability of the process by reapplication of the spent adsorbent and ultimately leading towards zero wastages. The performances of the adsorbents were verified with wastewater from electroplating industry. The scale-up study reported for industrial applications. ANN modelling using multilayer perception with gradient descent (GD) and Levenberg-Marquart (LM) algorithm had been successfully used for prediction of Cr(VI) removal efficiency. The study explores the undiscovered potential of the natural waste materials for sustainable existence of small and medium sector industries, especially in the third world countries by protecting the environment by eco-innovation.     

Improvement in rice straw pulp bleaching effluent quality by incorporating oxygen delignification stage prior to elemental chlorine-free bleaching

Environmental degradation by industrial and other developmental activities is alarming for imperative environmental management by process advancements of production. Pulp and paper mills are now focusing on using nonwood-based raw materials to protect forest resources. In present study, rice straw was utilized for pulp production as it is easily and abundantly available as well as rich in carbohydrates (cellulose and hemicelluloses). Soda-anthraquinone method was used for pulp production as it is widely accepted for agro residues. Bleaching process during paper production is the chief source of wastewater generation. The chlorophenolic compounds generated during bleaching are highly toxic, mutagenic, and bioaccumulative in nature. The objectives of study were to use oxygen delignification (ODL) stage prior to elemental chlorine-free (ECF) bleaching to reduce wastewater load and to study its impact on bleached pulp characteristics. ODL stage prior to ECF bleaching improved the optical properties of pulp in comparison to only ECF bleaching. When ODL stage was incorporated prior to bleaching, the tensile index and folding endurance of the pulp were found to be 56.6 ± 1.5 Nm/g and 140, respectively, very high in comparison to ECF alone. A potential reduction of 51, 57, 43, and 53% in BOD₃, COD, color, and AOX, respectively was observed on adding the ODL stage compared to ECF only. Generation of chlorophenolic compounds was reduced significantly. Incorporation of ODL stage prior to bleaching was found to be highly promising for reducing the toxicity of bleaching effluents and may lead to better management of nearby water resources.

Open image in new window

Graphical abstract ?