Profile of trace elements in Parasol Mushroom (Macrolepiota procera) from Tucholskie Forest

The aim of this study was to determine 19 elements contents and bioconcentration potential in fruiting bodies of Parasol Mushroom (Macrolepiota procera) collected from the Tucholskie Forest complex in Poland. Also discussed were Cd, Pb and Hg contents of edible caps in relation to the current regulatory standards. K, P and Mg were particularly abundant in caps and stipes, median values were 38-49, 13, and 1.6-1.6 mg/g dry weight, and followed by Ca, Na and Rb at 110-540, 44-240 and 20-50 μg/g dw, respectively. Concentrations of Al, Fe, Zn, Cu and Mn were from less than 50 to 180 μg/g dw, while concentrations of other elements were ～l.0?μg/g dw or less. Cu, K, Ag, Cd, Na, Rb, Zn and Hg were bioconcentrated (BCF >1), while Al, Ba, Fe, Mn, Co, Sr, Pb and Cr were not bioaccumulated (BCF <1). Cd and Pb content of Parasol Mushroom's edible caps collected from some sites in the Tucholskie Forest exceed the maximum levels set in the EU for cultivated mushrooms.     

PCDDs/PCDFs, dl-PCBs and HCB in the flue gas from coal fired CFB boilers

The aim of the project was to measure the actual emissions of polychlorinated dibenzodioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), dioxin-like polychlorinated biphenyls (dl-PCBs) and hexachlorobenzene (HCB) from four selected power plants in Poland in order to update the national inventory of PCDDs/PCDFs emission. Relatively low PCDDs/PCDFs as well as dl-PCBs concentrations in flue gas obtained in measurements in this study for four different circulated fluidized bed (CFB) boilers indicate practical absence of any hazards caused by PCDDs/PCDFs emission from these units. The results of PCDDs/PCDFs determination obtained in this study indicate that hard coal combustion in large CFB in the four central heating plants (CHP) is not a significant source of PCDDs/PCDFs emission to the environment even if operated by co-firing of waste coal. PCDDs/PCDFs concentration in flue gases as well as emission factors were recorded in the range of 0.012-0.060ngI-TEQ/m(n)(3) and 7.51-46.4mugI-TEQ/TJ, respectively. Dl-PCBs concentration was practically below the LOQ=0.006ng WHO-PCB TEQ/m(n)(3) in all experiments. HCB concentration as well as emission factors were recorded in the range of 11.5-42.0ng/m(n)(3) and 6.19-26.7mg/TJ, respectively, where the highest value was obtained for co-firing of waste coal, however. Obtained in this work emission factors will be used for national emission inventory purposes instead of the factors proposed by Toolkit or taken from previous measurements. However, consideration should be given to the fact that the measurements in most cases are related to single installations. Therefore, the need for further development of national factors for the power generation industry in Poland is desired.     

Assessment of the pollution and ecological risk of lead and cadmium in soils

The aim of the study was to assess the content, distribution, soil binding capacity, and ecological risk of cadmium and lead in the soils of Malopolska (South Poland). The investigation of 320 soil samples from differently used land (grassland, arable land, forest, wasteland) revealed a very high variation in the metal content in the soils. The pollution of soils with cadmium and lead is moderate. Generally, a point source of lead and cadmium pollution was noted in the study area. The highest content of cadmium and lead was found in the northwestern part of the area—the industrial zones (mining and metallurgical activity). These findings are confirmed by the arrangement of semivariogram surfaces and bivariate Moran’s correlation coefficients. Among the different types of land use, forest soils had by far the highest mean content of bioavailable forms of both metals. The results showed a higher soil binding capacity for lead than for cadmium. However, for both metals, extremely high (class 5) accumulation capacities were dominant. Based on the results, the investigated soils had a low (Pb) and moderate (Cd) ecological risk on living components. Soil properties, such as organic C, pH, sand, silt, and clay content, correlated with the content of total and bioavailable forms of metals in the soils. The correlations, despite being statistically significant, were characterized by very low values of correlation coefficient (r?=?0.12–0.20, at p?≤?0.05). Therefore, the obtained data do not allow to define any conclusions as to the relationships between these soil properties. However, it must be highlighted that there was a very strong positive correlation between the total content of cadmium and lead and their bioavailable forms in the soils.     

Measurement of selected indoor physical environmental factors in hairdresser salons in a Turkish City

Objectives The purpose of this study was to determine electromagnetic fields, electric fields, humidity, temperature, and illumination levels in hairdresser salons located in the downtown area of Aydin, Turkey. Also some health problems which could be related with the occupational factors are evaluated. Materials and methods The study was carried out in 30 hairdresser salons, all of which had been registered within the past 5 years. Electric and electromagnetic fields, illumination, temperature and humidity measurements were determined for hairdryers, hood hairdryers and depilatory heaters in the participating salons. A brief questionnaire about characteristics and the health status of hairdressers and workplace conditions was prepared and administered to the hairdressers at the salons. Results The mean electric fields of hairdryers, hood hairdryers and depilatory heaters were determined as 518 ± 74, 1,123 ± 199, and 648 ± 146 in V/m, respectively, at 5 cm from the surface of each device. These appliances generate mean electromagnetic fields in excess of 0.25 μT at 5 cm: hand-held hairdryers, 5.0 ± 0.7 μT; hood hairdryers, 1.6 ± 0.3 μT; and depilatory heaters 1.9 ± 0.6 μT. Total average of cumulative electric and electromagnetic fields, measured at a distance of 90 cm from the surface of these three devices was calculated to be 98.8 V/m and 0.5 μT, in the participating salons. Conclusions This preliminary study suggests that physical environmental factors in the salons may be contributing to the health problems of the hairdressers, and the electrical equipments in the workplaces may have cumulative electric and electromagnetic effects.     

RP-HPLC determination of phytoplankton pigments—comparison of calibration results for two columns

In the experiment reported the results obtained with two different columns for the RP-HPLC analysis of phytoplankton pigment components were compared. LiChroCART Hypersil ODS and LiChroCART LiChrospher 100 RP18e columns were used exchangeably. Two groups of high-purity pigment standards of reference phytoplankton strains (23 chlorophylls and carotenoids in the first case and 25 in the second case) were subjected to chromatographic analysis. All calibration parameters (retention times, calibration curves, spectrum shapes, detection thresholds) for qualitative and quantitative identification of pigments were determined. The results indicate that both columns used in the analysis ensure sufficient resolution and can be used interchangeably for the analysis of pigments present in naturally existing phytoplankton, even when present in only trace amounts.Communicated by O. Kinne, Oldendorf/Luhe     

Vegetation of the selected forest stands and land use in the Carpathian Mountains

Within the framework of the project "Effects of forest health on biodiversity with emphasis on air pollution in the Carpathian Mountains" 26 permanent study sites were established in the vicinity of the ozone monitoring sites. The study sites were located on the NW-SE transect through the Western (12 sites), Eastern (11 sites) and Southern (3 sites) Carpathians in forest ecosystems typical of each area. Some of the forest monitoring sites were located in national parks, biosphere reserves and areas of protected landscape. Each permanent site of 0.7 ha area consisted of 5 small 500m(2) circular plots, arranged in the form of a cross, i.e. four placed on the cardinal points (N, E, S, W) and one in the center. Phytosociological records were done twice during the 1998 growing season using the Braun-Blanquet's method. The study sites represented various types of forest: Picea abies stands (8), beech (Fagus sylvatica) stands (10), fir (Abies alba) stands (2) and mixed beech-fir, spruce-fir and beech-spruce stands (6). Age of most stands was 80-100 years. Degree of crown damage varied greatly between sites, a percentage of damaged trees decrease in Carpathians from West to East. It corresponds well with the O(3) level in these areas. Typical damage by O(3) in herb layer species in several Carpathian sites were found. Land-use map for the entire Carpathian Mountains and two detailed land use maps for Tatras (Western Carpathians) and Retezat (Southern Carpathians) are presented. A little more than half of the Carpathian territory is forested. The most densely forested are Eastern Carpathians, while the most sparsely Western Carpathians. Arable lands occupy 22.6% of the Carpathians, pastures and meadows 6.2%, water bodies 1.9%, and build up areas several percent. In the highest elevation of the Carpathians alpine meadows (11.3%) and rocks (3.5%) are distributed.     

A roadmap for the conservation of freshwater mussels in Europe

Europe has a long history of human pressure on freshwater ecosystems. As pressure continues to grow and new threats emerge, there is an urgent need for conservation of freshwater biodiversity and its ecosystem services. However, whilst some taxonomic groups, mainly vertebrates, have received a disproportionate amount of attention and funds, other groups remain largely off the public and scientific radar. Freshwater mussels (Bivalvia, Unionida) are an alarming example of this conservation bias and here we point out six conceptual areas that need immediate and long-term attention: knowledge, threats, socioeconomics, conservation, governance and education. The proposed roadmap aims to advance research, policy and education by identifying the most pressing priorities for the short- and long-term conservation of freshwater mussels across Europe.     

Investigations of ash topography/morphology and their relationship with heavy metals leachability

The leachability of heavy metals such as chromium (Cr), lead (Pb) and cadmium (Cd) from the ash material obtained from waste combustion was studied. The effects of ash surface topography and morphology on the leachability of these elements were examined using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM (scan size 10 x 10 microns) and SEM images of the simulated ash pellet obtained at various operating temperatures (1000, 1400 and 1500 degrees C) showed significant microstructural and topographical changes. Ash pellets treated at 1000 degrees C contain porous and non-continuous surface. On the other hand, the ash pellet obtained at higher temperature (1500 degrees C) was found to contain a smooth, continuous and non-porous surface. The AFM height profile studies indicated that the top surface variation of the ash pellet at 1000, 1400 and 1500 degrees C were found to be -40.0 to 25.5, -3.7 to 4.7 and -0.10 to 0.66 nm respectively. The SEM analyses also confirmed the presence of smooth, non-porous outer surface of ash formed at 1500 degrees C. In addition, it also showed the presence of compact and rigid interior for the same ash pellet. The leachability of the heavy metals was determined using standard toxicity characteristic leaching procedure (TCLP) test and the samples were analysed using atomic absorption spectroscopy. The results showed that the TCLP leaching ratios of the heavy metals were Cr = 0.30, Pb = 0.05 and Cd = 0.09 at 1000 degrees C. However, the ash obtained at 1400 degrees C showed negligible heavy metals leaching ratio while at 1500 degrees C no leachability was detected (TCLP concentration dropped to nondetectable levels). The use of high temperature treatment enabled the immobilization of heavy metals in the ash preventing their leaching. Such ash can be considered as a non-hazardous material for reuse or safe disposal.     

Procedures of trophic chain samples preparation for determination of triazines by HPLC and metals by ICP-AES methods

The aim of this research was monitoring the distribution of atrazine and simazine as well as metals Pb, Cd, Zn, Al, Co, Ni, and V along with trophic chains: soil-vegetables and soil, carrot or grass and meat. Different techniques of herbicides extraction by means of many solvents were examined. Triazines were analysed by means of HPLC, metals by means of ICP-AES. Detection limits: LOD=0.2 microg ml(-1), determination limits: LOQ=0.73 microg ml(-1) for atrazine and LOD=0.3 microg ml(-1), LOQ=1.12 microg ml(-1) for simazine were obtained. The content (microg g(-1)) of simazine in soil was in range: 3.45-8.60, in vegetable roots: 6.62-38.15, in vegetable leaves: 2.45-31.71, in rabbit fat: 0.13-49.90. The content (microg g(-1)) of atrazine in soils was in range: 11.9-13.03, in vegetable roots: 13.61-92.90. In analysed material the particular metals after microwave or dry digestion were determined in range (microg g(-1)): Pb: 6.48-43.18; Cd: 0.11-0.57; Zn: 8.79-51.90; Al: 10.22-24.48; Co: 0.18-3.89; Ni: 0.37-6.36; V: 0.29-1.48.