Wet oxidative regeneration of activated carbon loaded with reactive dye

Wet Oxidative Regeneration (WOR) of powdered activated carbon (PAC) and granular activated carbon (GAC) loaded with the reactive dyes, namely chemictive brilliant blue R and cibacron turquoise blue G, was studied. Attempts were made to regenerate the loaded carbons designated now as spent carbon. A slurry (10% w/v) of spent carbon in distilled water was oxidized by wet oxidation in the temperature range of 150-250 degrees C using oxygen partial pressures between 0.69-1.38 MPa in an 1 1 SS 316 autoclave. The percent regeneration was determined from a ratio, X(RC)/X(VC), corresponding to an equilibrium adsorption capacity of regenerated carbon/equilibrium adsorption capacity of virgin carbon from an initial adsorption period of 3 h. It was observed that the regeneration mainly occurred due to the oxidation of the adsorbates taking place on the surface of carbon. It was possible to regenerate the spent GAC and PAC to the extent of more than 98% (approximately X(RC)/X(VC) > 0.98) by wet oxidation. After four consecutive cycles of adsorption and regeneration using the same stocks of GAC, carbon weight loss observed at 200 degrees C was about 40%. SEM studies of the regenerated carbon showed widening of the pores and loss of structure between the adjacent pores as compared with the virgin carbon. PAC was found to be more suitable as compared with GAC for the adsorption and wet oxidative regeneration processes to treat the aqueous solution containing lower concentration of unhydrolyzed reactive dye. The suitability of wet oxidative regeneration is demonstrated at a bench scale to treat the synthetic reactive dye solution.     

Recycling of high purity selenium from CIGS solar cell waste materials

Copper indium gallium diselenide (CIGS) is a promising material in thin film solar cell production. To make CIGS solar cells more competitive, both economically and environmentally, in comparison to other energy sources, methods for recycling are needed. In addition to the generally high price of the material, significant amounts of the metals are lost in the manufacturing process. The feasibility of recycling selenium from CIGS through oxidation at elevated temperatures was therefore examined. During oxidation gaseous selenium dioxide was formed and could be separated from the other elements, which remained in solid state. Upon cooling, the selenium dioxide sublimes and can be collected as crystals. After oxidation for 1 h at 800 °C all of the selenium was separated from the CIGS material. Two different reduction methods for reduction of the selenium dioxide to selenium were tested. In the first reduction method an organic molecule was used as the reducing agent in a Riley reaction. In the second reduction method sulphur dioxide gas was used. Both methods resulted in high purity selenium. This proves that the studied selenium separation method could be the first step in a recycling process aimed at the complete separation and recovery of high purity elements from CIGS.     

Photocrosslinking of an Acrylated Epoxidized Linseed Oil: Kinetics and its Application for Optimized Wood Coatings

Over the past few decades, the industry developed an increasing interest in using renewable, bio-based thermosetting polymers as matrix systems for composites and coating systems. In the present paper an acrylated epoxidized linseed oil (AELO) was synthesized from epoxidized linseed oil (ELO) through ring opening of the oxirane group using acrylic acid as the ring opening agent. The synthesized AELO was mixed with three different photoinitiators and cured under monochromatic conditions (???=?365?nm) at different light intensities and at different temperatures. The concentration of the initiators was aligned that all initiators absorb at 365?nm the same amount of light. The evolution of cure was monitored by using real-time infrared spectroscopy with a heated attenuated total reflection unit. The decrease of absorption in the measured spectra at 1,406?cm^?1 was used to calculate the conversion of acrylic double bonds with increasing time of UV light exposure to get information about the cure kinetics for each AELO mixture at different light intensities and different temperatures. Wood substrates were coated in a preliminary work with the AELO mixtures and after UV-curing some technological coating properties like gloss, scratch resistance, adhesion, and solvent resistance were tested. In combination with the information about the cure kinetics in the present work the coating properties were correlated with the cure evolution and the final degree of double bond conversion. The found correlation can be used in the future to find optimized coating conditions for the AELO mixtures on wood substrates.     

Recycling and recovery routes for incinerated sewage sludge ash (ISSA): A review

The drivers for increasing incineration of sewage sludge and the characteristics of the resulting incinerated sewage sludge ash (ISSA) are reviewed. It is estimated that approximately 1.7 million tonnes of ISSA are produced annually world-wide and is likely to increase in the future. Although most ISSA is currently landfilled, various options have been investigated that allow recycling and beneficial resource recovery. These include the use of ISSA as a substitute for clay in sintered bricks, tiles and pavers, and as a raw material for the manufacture of lightweight aggregate. ISSA has also been used to form high density glass–ceramics. Significant research has investigated the potential use of ISSA in blended cements for use in mortars and concrete, and as a raw material for the production of Portland cement. However, all these applications represent a loss of the valuable phosphate content in ISSA, which is typically comparable to that of a low grade phosphate ore. ISSA has significant potential to be used as a secondary source of phosphate for the production of fertilisers and phosphoric acid. Resource efficient approaches to recycling will increasingly require phosphate recovery from ISSA, with the remaining residual fraction also considered a useful material, and therefore further research is required in this area.     

Environmental Effects Monitoring in Sydney Harbor During Remediation of One of Canada's Most Polluted Sites: A Review and Lessons Learned

This article reviews a comprehensive marine environmental effects monitoring program (MEEMP) comprised of components capable of detecting changes in the marine environment over short or extended temporal scales during remediation of one of Canada's most polluted sites at the Sydney Tar Ponds. The monitoring components included: water and sediment quality, amphipod toxicity testing, mussel tissue, crab hepatopancreas tissue, and benthic community assessments. The MEEMP was designed to verify the impact predictions for the remediation project (i.e., no immediate damage to the marine ecosystem through remediation activities). Some components were capable of providing conclusive data (e.g., sediment and water quality), while others only yielded data that were inconclusive or difficult to attribute to remediation activities (e.g., intertidal community assessments and amphipod toxicity testing). Components that provided only inconclusive results or were difficult to attribute to remediation activities were discontinued, resulting in substantial cost savings during the project, but without compromising the overall objectives of the program, which was to monitor for potential adverse environmental effects of remediation on the marine environment in Sydney Harbor and to verify environmental effects predictions made in the Environmental Impact Statement for the project. The rationale for discontinuing certain MEEMP components and discussion of conclusive results are incorporated into “lessons learned” for environmental remediation practitioners and regulators working on similar large‐scale multiyear remediation projects. © 2014 Wiley Periodicals, Inc.     

Real time alteration of a nuclear waste glass and remobilization of lanthanide into an interphase

The development of predictive models for the long term evolution of nuclear waste glass requires the complete knowledge of the glass dissolution at the laboratory scale. A new approach was developed to determine the initial reaction during the first steps of experience, a new concept was developed, based on the combination of dynamic leaching test and the characterization of the altered materials. With this experimental set-up it is possible to follow in real time the glass alteration process at a fine temporal scale. The results put in evidence a singular behaviour of the lanthanide, shown by a concentration peak of La, Nd and Ce after 2 h and a quick decrease of their concentration measured on line in the solution during the leaching test. This fact is directly linked to the development of an interphase (altered layer which differs from the initial solid by its texture, structure and chemical composition) at the interface of the glass surface and the leaching solution. This work is an attempt to integrate the formation of the alteration products (here the interphase) during leaching into the dissolution mechanisms of a nuclear waste glass. A model is proposed and discussed.     

Development of Thixotropic Coatings Using Dimerized Soybean Oil Fatty Acids: The Case of Polyamide of 1,2-Phenylene Diamine

Soybean oil (SBO) was dimerized and the crude dimer acid product reacted with 1,2-phenylene diamine at 210 ± 5 °C under inert atmosphere to obtain fatty polyamide (FPA). The FPA was used to modify a commercial alkyd resin by reacting a mixture of the alkyd resin with 5 wt% of FPA at 120 °C for 80 min under inert atmosphere. The FTIR spectrum of the FPA modified resin showed evidence of higher degree of H-bonding than was found for the unmodified alkyd. White gloss coatings of 15, 20, 25, and 30% solids were formulated from the modified and unmodified resins and examined for performance with respect to: leveling, sag resistance, drying time, pigment settling, skinning tendency and film hardness. Results showed that the unmodified alkyd coatings exhibited good leveling but poor sag resistance at all solid contents. In contrast, FPA modified alkyd coatings combined good leveling with high sag resistance indicating their thixotropic nature. A strong tendency to pigment settling was observed for unmodified alkyd coatings but was not observed in the FPA modified alkyd coatings. The modified alkyd coatings showed skinning while the unmodified alkyd coatings did not skin. A 30% solids coating formulation of the FPA modified resin showed shorter surface dry time but longer hard dry time than the unmodified alkyd resin coating.