Improving the quality of waste-derived char by removing ash

This study characterized and removed ash from waste-derived char to improve the quality of char as fuel. Municipal solid waste (MSW) and automobile shredder residue (ASR) were carbonized at 450 degrees C and at 500 degrees C, respectively, in a rotary kiln with a nitrogen atmosphere for 1h. MSW and ASR char were subjected to sieving and pulverization-sieving to screen incombustibles and the ash-rich fraction, after which float-sink separation, froth floatation, and oil agglomeration were applied to remove ash from the char. The established target quality was (1) less than 30% ash content and (2) more than 20,000 kJ/kg heating value. However, the rate of combustibles recovery had to be lowered to produce a good quality of char along with a high heating value. MSW char attained the targeted quality level using froth floatation or oil agglomeration, whereas, neither separation method was able to make ASR-derived char satisfy the target. Based on the assumption that particle properties of char are determined by the weight ratio of combustibles and ash, the densities of combustibles and ash in char were estimated using the results of float-sink separation, X-ray diffraction (XRD) analysis, and elemental content. To verify the above assumption, an energy dispersive X-ray/scanning electron microscope (EDX/SEM) analyzer was used to observe char particles.     

Batch separation of shredded bulky waste by gas-solid fluidized bed at laboratory scale

A gas-solid fluidized bed separator using various bed materials was used to separate shredded municipal bulky waste (SBW). Using 290 microm glass beads as the bed material, the apparent density of the fluidized bed was 1.5 g/cm(3) and the SBW could be separated into combustibles such as wood, paper and plastics and incombustibles such as metals and glass. The overall efficiency (Newton's efficiency) of the separation was calculated to be 0.93. In order to obtain high efficiency, the superficial velocity must be adjusted so that the fluidized bed is agitated moderately and at the same time there is no weak fluidized region. Using a mixture of particles of nylon shot and 68 microm glass beads, the apparent density of the fluidized mixture bed could be varied between 0.63 and 0.99 g/cm(3) by changing the mixing ratio of the two materials. In the case of a mixing ratio of 20% for glass beads, an apparent density of 0.65 g/cm(3) was produced, in which wood and paper components were recovered while plastics remained in the bed to give a final overall efficiency of 0.88.     

Past, present, and future of MSW landfills in Japan

This article focuses on the historical development of landfill technology since the beginning of the nineteenth century in Japan. The regulations and guidelines that form a framework for the technology are reviewed, and the historical background and the current state of Japanese municipal solid waste (MSW) management are described. Through the analysis of data collected from facility leaflets, changes in the leachate treatment system are surveyed. Finally, the concept of the “sustainable bioreactor landfill with low organics” is proposed.     

Resident's concerns and attitudes towards Solid Waste Management facilities

Because of limited space, the siting and construction of a new SWM facility is a big challenge in Japan. An SWM facility should be socially accepted as well as environmentally and economically sound. This study aimed to investigate people's concerns about SWM facilities and their attitudes towards such facilities. A questionnaire was designed based on literature reviews and was sent to residents in three municipalities with different backgrounds. The questions covered concerns on the impact of an SWM facility, management aspects, unfairness of facility siting, and attitudes to facility construction. Of the many concerns, "pollution and health effect" had the highest rating, followed by "reliability", "damage to nature" and "cost". The rating was different between municipalities, reflecting their geographic and social backgrounds. Using factor analysis, correlations among concerns were analyzed, and five principal components were extracted, namely "pollution", "nuisance", "facility management", "planning of facility", and "merit/demerit". Although obvious correlations were not found between individual items of concern and attitudes to construction of a facility, the discriminant analysis indicated dominant concerns of attitudes, but the disagreement between actual impact and citizens were found. As for attributes, the "opposed" attitude decreased for residents who had visited an SWM facility, even if they had only seen it from outside.     

Behavior of metals in ash melting and gasification-melting of municipal solid waste (MSW)

In this study, metal behavior in ash-melting and municipal solid waste (MSW) gasification-melting facilities were investigated. Eight ash-melting and three MSW gasification-melting facilities with a variety of melting processes and feedstocks were selected. From each facility, melting furnace fly ash (MFA) and molten slag were sampled, and feedstock of the ash-melting processes was also taken. For the ash melting process, the generation rate of MFA was well correlated with the ratio of incineration fly ash (IFA) in feedstock, and this was because MFA was formed mostly by mass transfer from IFA and a limited amount from bottom ash (BA). Distribution ratios of metal elements to MFA were generally determined by volatility of the metal element, but chlorine content in feedstock had a significant effect on Cu and a marginal effect on Pb. Distribution ratio of Zn to MFA was influenced by the oxidizing atmosphere in the furnace. High MFA generation and distribution ratio of non-volatile metals to MFA in gasification-melting facilities was probably caused by carry-over of fine particles to the air pollution control system due to large gas volume. Finally, dilution effect was shown to have a significant effect on metal concentration in MFA.     

Material and heavy metal balance in a recycling facility for home electrical appliances

Collection and recycling of home electrical appliances was started in Japan in 2001 under a new recycling law. The law is aimed at promoting material recycling and at reducing the amount of waste to be landfilled. End of life products are processed by manual disassembly, shredding, and separation in 38 recycling facilities. The authors conducted a questionnaire survey and interviewed at some facilities to obtain information on process flow and material balance. By using the detailed records offered by one facility and by estimating the composition of recovered components, the material balance in the facilities was determined for four typical recycling processes. The heavy metal content of the recovered components was analyzed, then metal flow in the process was determined for each scenario. As a result, it was concluded that emissions to the environment of most heavy metals have been substantially reduced by the new recycling system, while a modest improvement in the rate of material recovery has been achieved.