Occupational exposure

Concentrations of polychlorinated biphenyls (PCB), polychlorinated naphthalenes (PCN), polychlorinated dibenzo-p-dioxins (PCDD), polychlorinated dibenzofurans (PCDF), hexachlorobenzene and methylsulphonyl metabolites of PCB were determined in blood plasma from potentially exposed workers and controls. Three of the potentially exposed subjects had worked with cable incineration and two were electricians. Extraction of the organochlorine compounds and lipids were performed using the lipophilic gel Lipidex. Different adsorbents and gel permeation chromatography were applied for further purification of the samples and separation of analytes. Determinations of the chlorinated compounds were made by using gas chromatography with electron-capture detection and gas chromatography-mass spectrometry. Only small differences in the concentrations of organochlorine compounds were found in the plasma from the three subject groups. Thus, specific exposure of the workers could not be confirmed.     

Hand-arm vibration disorder among grass-cutter workers in Malaysia

Introduction. Prolonged exposure to hand-transmitted vibration from grass-cutting machines has been associated with increasing occurrences of symptoms and signs of occupational diseases related to hand–arm vibration syndrome (HAVS). Methods. A cross-sectional study was carried out using an adopted HAVS questionnaire on hand–arm vibration exposure and symptoms distributed to 168 male workers from the grass and turf maintenance industry who use hand-held grass-cutting machines as part of their work. The prevalence ratio and symptom correlation to HAVS between high and low–moderate exposure risk groups were evaluated. Results. There were positive HAVS symptoms relationships between the low–moderate exposure group and the high exposure group among hand-held grass-cutting workers. The prevalence ratio was considered high because there were indicators that fingers turned white and felt numb, 3.63, 95% CI [1.41, 9.39] and 4.24, 95% CI [2.18, 8.27], respectively. Less than 14.3% of workers stated that they were aware of the occupational hand–arm vibration, and it seemed to be related to the finger blanching and numbness. Conclusion. The results suggest that HAVS is under-diagnosed in Malaysia, especially in the agricultural sectors. More information related to safety and health awareness programmes for HAVS exposure is required among hand-held grass-cutting workers.     

Levels of heavy metals (Zn,Cu, Cd,and Pb) in mudskippers (Periophthalmodon schlosseri) and sediments collected from intertidal areas at Morib and Remis,Peninsular Malaysia

The concentrations of Zn, Cu, Cd, and Pb were determined in different tissues of mudskipper fishes Periophthalmodon schlosseri caught at two selected locations (Morib and Remis) of the intertidal mudflat area of Selangor state, West Coast of Peninsular Malaysia and in surface sediment samples. Metal concentrations in the mudskipper tissue and in the sediment samples tended to vary significantly (p < 0.05) between the two locations. Higher metal concentrations (except for Zn) were mostly found in the tissues of mudskippers from Remis. For sediment samples, significantly (p < 0.05) higher metal concentrations of all metals were also found at Remis. Generally, metal distribution between different tissues of mudskipper varied with scales being highly accumulative of Zn, Cd, and Pb, while for Cu, the highest mean concentrations were found in the liver. The lowest mean concentrations of Zn, Cu, and Cd were found in the muscles except for Pb, which was lowest in the liver. This study suggests that mudskippers can be potential biomonitoring organisms for heavy metal bioavailability and contamination of intertidal coastal mudflats. The concentrations of Cd and Pb were slightly above the acceptable limits of Malaysian and European food safety guidelines.     

Potential of microalgae Bio-Coke as a sustainable solid fuel alternative to coal coke

Energy and environmental issues have triggered the search for new sources of green energy alternatives in recent years. Biofuel production from renewable sources is widely considered one of the most sustainable alternatives for environmental and economic sustainability. Microalgae are currently being promoted as one of the most promising liquid biofuel feedstocks due to their rapid growth, high lipid production capacity, and carbon–neutral cycle. In this study, whole microalgae cells were utilized as raw material to produce solid biofuel, i.e., Bio-Coke, and this study aimed to investigate the possibility of microalgae Bio-Coke as an alternative to coal coke. The results show that Bio-Coke can be produced from microalgae in the temperature range of 80–100 °C. The apparent density is between 1.253 and 1.261 g/cm³, comparable to the apparent density of lignocellulosic Bio-Coke. Additionally, the calorific value is higher than the calorific value of lignocellulosic Bio-Coke and within the range of the calorific value of subbituminous coal. Therefore, microalgae Bio-Coke can be utilized to replace coal coke usage in the future.

     

Critical success factors of sustainable manufacturing practices in Malaysian automotive industry

The purpose of this study is to examine the critical success factors of sustainable manufacturing practices (SMPs) in Malaysian automotive industry. The questionnaires were designed and distributed to the 50 respondents. The pilot study sample consists of 26 respondents from 50 questionnaires, with an average response rate of 52%. The results of reliability analysis show that social responsibility is critical factor influencing the direct SMPs implementation success. By implementing SMPs in Malaysian automotive industry, it can assist company to improve the quality of management. Thus, this study recommends that the future research explore the influence of SMPs on sustainable performance in Malaysian automotive industry.     

Monotonic aspects of the mechanical behaviour of bottom ash from municipal solid waste incineration and its potential use for road construction

Municipal solid waste incineration (MSWI) bottom ash is an atypical granular material because it may include industrial by-products that result from the incineration of domestic waste. The prospects for the beneficial use of this particular material mainly lie in the field of road construction, as a substitute for the traditional natural aggregates. However, its mechanical properties are still little known, particularly in term of stiffness and deformability, characteristics that are essential to the construction of a durable roadway. The purpose of this paper is to describe better the mechanical behaviour of this recycled material. In order to reach this objective, a large experimental campaign is presented. The first part of this paper presents and comments in detail on the results obtained from static monotonic tests. Oedometric and triaxial shear tests were performed on MSWI bottom ash both before and after treatment with a specific hydraulic binder. These tests allow specification of the mechanical characteristics of the MSWI bottom ash, such as the initial Young's modulus, Poisson's ratio, the compressibility index, the friction angle, and the contracting or dilating behaviour of the material. The results reveal a mechanical behaviour similar to that of initially dense standard materials (sands, unbound granular materials) and a dependence on the applied average pressure, characteristic of the mechanical behaviour of granular media. More laboratory data on other samples of MSWI bottom ash are required to ensure that this comparison is statistically valid.     

Discriminant analysis for the prediction of sand mass distribution in an urban stormwater holding pond using simulated depth average flow velocity data

The approach of this paper is to predict the sand mass distribution in an urban stormwater holding pond at the Stormwater Management And Road Tunnel (SMART) Control Centre, Malaysia, using simulated depth average floodwater velocity diverted into the holding during storm events. Discriminant analysis (DA) was applied to derive the classification function to spatially distinguish areas of relatively high and low sand mass compositions based on the simulated water velocity variations at corresponding locations of gravimetrically measured sand mass composition of surface sediment samples. Three inflow parameter values, 16, 40 and 80 m³ s^?1, representing diverted floodwater discharge for three storm event conditions were fixed as input parameters of the hydrodynamic model. The sand (grain size?>?0.063 mm) mass composition of the surface sediment measured at 29 sampling locations ranges from 3.7 to 45.5 %. The sampling locations of the surface sediment were spatially clustered into two groups based on the sand mass composition. The sand mass composition of group 1 is relatively lower (3.69 to 12.20 %) compared to group 2 (16.90 to 45.55 %). Two Fisher’s linear discriminant functions, F ₁ and F ₂, were generated to predict areas; both consist of relatively higher and lower sand mass compositions based on the relationship between the simulated flow velocity and the measured surface sand composition at corresponding sampling locations. F ₁?=??9.405?+?4232.119?×?A???1795.805?×?B?+?281.224?×?C, and F ₂?=??2.842?+?2725.137?×?A???1307.688?×?B?+?231.353?×?C. A, B and C represent the simulated flow velocity generated by inflow parameter values of 16, 40 and 80 m³ s^?1, respectively. The model correctly predicts 88.9 and 100.0 % of sampling locations consisting of relatively high and low sand mass percentages, respectively, with the cross-validated classification showing that, overall, 82.8 % are correctly classified. The model predicts that 31.4 % of the model domain areas consist of high-sand mass composition areas and the remaining 68.6 % comprise low-sand mass composition areas.     

Enhancement of Tensile Strength and Flexibility of Polycaprolactone/Tapioca Starch Blends by Octadecylamine Modified Clay

Polycaprolactone/tapioca starch/octadecylamine modified clay (OMMT) nanocomposites were successfully prepared by melt blending. X-ray diffraction and transmission electron microscopy (TEM) of the products showed that they are nanocomposites of a mixture intercalated and exfoliated types. In addition, the TEM also revealed that the OMMT layers are homogeneously distributed in the polymer matrix. The presence of 1 php of OMMT improved the compatibility of the polymers in the blends which consequently increased the tensile strength of the blend of more than 60% and elongation at break of more than 1,000%.     

Carbon emissions from the peat fire problem—a review

Environmental Science and Pollution Research - Peat fires in tropical peatland release a substantial amount of carbon into the environment and cause significant harm to peatlands and the ecology,...