莱特生物强化技术处理高浓度有机废水的中试

采用莱特生物强化技术(LTBR—Littoral BioReactor),对兰州石化公司化工园区高浓度有机废水进行了中试试验,进行了正常运行的常规标定、水量冲击标定、浓度冲击标定。结果表明:采用LTBR生物处理工艺,使用特效微生物和营养基质,可以在高COD、高含盐等不利条件下正常进行有机物降解,达到了必须将废水中的COD降至2000mg/L以下的试验要求,为处理高浓度有机化工废水的工程应用开辟了新思路。     

锰铜铈氧化物催化剂氧化NO性能及动力学研究

实验以TiO2为载体采用浸渍法制备CuOx/TiO2、CeOx/TiO2、CuCeOx/TiO2和MnCuCeOx/TiO2催化剂,考察这些催化剂氧化NO活性,探究Cu、Ce摩尔比和添加Mn元素对CuCeOx/TiO2催化剂氧化NO活性的影响,使用扫描电镜观察催化剂表面结构。研究发现,Cu、Ce元素配合后的CuCeOx/TiO2催化剂氧化活性明显好于单独含Cu、Ce的催化剂,当Cu、Ce摩尔比为Cu:Ce=1∶2时,CuCeOx/TiO2催化剂氧化活性最好,在NO浓度500×10-6,O210%,空速为24 000 h-1,350℃时,NO氧化度为0.62;添加Mn元素可以提高CuCeOx/TiO2催化剂低温氧化活性,250℃时,MnCuCe/Ti-3和MnCuCe/Ti-5催化剂氧化度为0.53和0.69,300℃时,MnCuCe/Ti-3和MnCuCe/Ti-5催化剂氧化度均为0.76;此外,实验还研究了NO在MnCuCe/Ti-3催化剂上反应的动力学方程。     

RPB-O3/H2O2法处理硝基苯模拟废水

在超重力场中,研究了硝基苯模拟废水的臭氧/双氧水(O3/H2O2)法处理效果,考察了超重力因子β、H2O2浓度、初始p H、液体流量及处理时间等因素对硝基苯去除率的影响。结果表明,硝基苯去除率随超重力因子β和处理时间的增加而增大,而随H2O2浓度、初始p H和液体流量的增加呈先增大后降低的趋势。当硝基苯初始浓度300 mg/L,工艺条件β=80、p H=10.0、臭氧质量浓度约为40 mg/L、H2O2浓度为4.9 mmol/L、液体流量为120 L/h时,循环处理35 min硝基苯去除率可达96.7%。处理时间60 min后,废水中硝基苯含量1.4 mg/L,COD为39 mg/L,达国家一级排放标准(GB 8978-1996)。在此条件下,硝基苯的降解过程符合准一级反应动力学。     

氨改性中孔活性炭对Pb(Ⅱ)的吸附

为讨论表面改性对活性炭吸附特性的影响,用氨改性活性炭对Pb(Ⅱ)的吸附性能进行了研究。通过高温氨气吹扫对活性炭进行表面改性处理,观察了改性后活性炭物化性质的变化,研究了氨改性活性炭对Pb(Ⅱ)的吸附等温关系与动力学,并对吸附前后氨改性活性炭的形貌进行了分析。结果表明,氨改性后活性炭比表面积和总孔孔容均略有增大,活性炭中N元素含量明显增高,含氧官能团数量减少,零电荷点增大。氨改性后活性炭对Pb(Ⅱ)的吸附效果明显提高,吸附过程数据可用等温吸附方程描述,改性后活性炭对Pb(Ⅱ)的吸附符合拟二级动力学。Pb(Ⅱ)在氨改性活性炭表面上的附着明显可见。通过红外光谱分析,活性炭表面含氮官能团与Pb(Ⅱ)发生缔合作用。     

Effect of temperature and particle size on the thermal desorption of PCBs from contaminated soil

Thermal desorption is widely used for remediation of soil contaminated with volatiles, such as solvents and distillates. In this study, a soil contaminated with semivolatile polychlorinated biphenyls (PCBs) was sampled at an interim storage point for waste PCB transformers and heated to temperatures from 300 to 600 °C in a flow of nitrogen to investigate the effect of temperature and particle size on thermal desorption. Two size fractions were tested: coarse soil of 420–841 μm and fine soil with particles <250 μm. A PCB removal efficiency of 98.0 % was attained after 1 h of thermal treatment at 600 °C. The residual amount of PCBs in this soil decreased with rising thermal treatment temperature while the amount transferred to the gas phase increased up to 550 °C; at 600 °C, destruction of PCBs became more obvious. At low temperature, the thermally treated soil still had a similar PCB homologue distribution as raw soil, indicating thermal desorption as a main mechanism in removal. Dechlorination and decomposition increasingly occurred at high temperature, since shifts in average chlorination level were observed, from 3.34 in the raw soil to 2.75 in soil treated at 600 °C. Fine soil particles showed higher removal efficiency and destruction efficiency than coarse particles, suggesting that desorption from coarse particles is influenced by mass transfer.     

Some technical issues in managing PCBs

Polychlorinated biphenyls (PCBs) were important industrial chemicals featuring high thermal and chemical stability and low flammability. They were widely used as dielectric and thermal fluid in closed electro-technical applications (transformers, capacitors…) and also in numerous dispersive uses, ranking from auto-copying paper to sealant or coatings. During the 1960s, severe environmental consequences started becoming apparent. The stability of PCBs contributed to their persistence in the environment, their lipophilic character to bio-magnification. Fish-eating species seemed threatened in their existence. In Japan and in Taiwan, thousands of people consumed PCB-contaminated oil. The production of PCBs stopped completely during the 1980s. Usage could continue in closed applications only. In this paper, particular attention is given to two issues: the cleaning of PCB electric transformers and the potential impact of PCB-containing building materials. Other contributions will cover the management and treatment of PCB-contaminated soil, sludge or fly ash. The complete survey is being prepared by request of the Knowledge Center for Engineers and Professionals.     

TiO2-Cu2O/蒙脱土复合光催化剂的制备与性能

以钠基蒙脱土（MMT）为载体,先采用溶胶-凝胶法将纳米TiO₂引入到MMT层间,再采用化学沉积法将纳米Cu₂O负载在TiO₂/MMT上,制备出TiO₂-Cu₂O/MMT纳米复合光催化剂。采用XRD、SEM、紫外-可见漫反射技术对催化剂进行了表征。以甲基橙为目标污染物,考察了催化剂的光催化性能。表征结果显示：TiO₂与Cu₂O均匀分布在MMT的表面与片层孔隙中;TiO₂-Cu₂O/MMT结合了TiO₂和Cu₂O的特性,拓宽了催化剂的光吸收范围。实验结果表明,在光源为可见光、初始甲基橙质量浓度为20 mg/L、光催化剂加入量为2 g/L的条件下,TiO₂-Cu₂O/MMT纳米复合光催化剂对甲基橙的光催化降解效果明显优于单一负载的Cu₂O/MMT和TiO₂/MMT,大幅提高了催化剂的光催化效率,反应300 min时TiO₂-Cu₂O/MMT对甲基橙溶液的脱色率达到93%。     

石化行业的VOCs排放控制管理

概述了我国挥发性有机化合物（VOCs）的排放情况。介绍了国内外VOCs的管理现状。分析了国内石化行业VOCs排放控制管理中存在的主要问题以及污染物排放过程的类别。提出了明确定义、制定相关标准、完善分类管理体系、研究最佳的可行性控制技术等加强VOCs排放控制管理的对策和建议。     

Photodegradation of azithromycin in various aqueous systems under simulated and natural solar radiation: kinetics and identification of photoproducts

This article describes the photolysis of azithromycin, a macrolide antibiotic with reported occurrence in environmental waters, under simulated solar radiation. The photodegradation followed first-order reaction kinetics in five matrices examined. In HPLC water, the degradation rate was the slowest (half-life: 20 h), whereas in artificial freshwater supplemented with nitrate (5 mg L⁻¹) or humic acids (0.5 mg L⁻¹) the degradation of azithromycin was enhanced by factors of 5 and 16, respectively, which indicated the role of indirect photolysis involving the formation of highly reactive species. Following chromatographic separation on a UPLC system, the characterization of the transformation products was accomplished using high-resolution QqToF-MS analysis. The presence of seven photoproducts was observed and their formation was postulated to originate from (bis)-N-demethylation in the desosamine sugar, O-demethylation in the cladinose sugar, combinations thereof, as well as from hydrolytic cleavages of the desosamine and/or cladinose residue. Two of these photoproducts could also be detected in natural photodegradation process in river water which was spiked with azithromycin.     

粗MnSO4溶液中MnS2O6的去除条件研究

用软锰矿吸收SO2生成MnSO4时会伴随有副产物MnS2O6生成。产品中MnS2O6的存在会降低硫酸锰产品质量,同时会缓慢释放出SO2气体污染环境。本文用单因素实验方法研究了粗MnSO4溶液中MnS2O6的最优去除条件。研究结果显示,软锰矿用量为12.2 g,硫酸加入量为20 mL、反应温度100℃、反应时间3 h、搅拌速度500 r/min,MnS2O6的去除率可达91%以上。其最终产品能达到GB1622-1986一级品标准。