双酚S在两种典型地带性土壤中的吸附/解吸行为研究

采用批平衡实验方法研究了双酚S（BPS）在两种典型地带性土壤中的吸附/解吸行为.结果表明,吸附动力学曲线符合拟二级动力学方程.吸附等温线呈非线性,且同时符合Freundlich和Langmuir方程.相比而言,BPS更易吸附在高有机质含量的黑土中,298 K反应温度下BPS在黑土和红壤上的最大吸附容量分别为497.8和156.6 mg·kg^-1.吸附到两种土壤中的BPS存在解吸滞后现象,这可能是由于BPS以化学吸附和微孔扩散的形式存在于土壤中的缘故.溶液pH与BPS在土壤中的吸附容量呈负相关关系,即中性形态的BPS比阴离子形态的BPS具有更高的吸附容量.与结构类似物双酚A（BPA）的吸附相比,BPS在土壤中的吸附量更低,因此具有更高的迁移能力,可能会引起更高的环境健康风险.本研究结果为了解BPS在土壤中的迁移规律提供了数据支持.     

北部湾南流江流域土地覆盖及生物多样性模拟

以北部湾独流入海河流南流江流域为研究对象,基于研究区2000年和2015年遥感数据解译的土地利用数据以及社会经济等数据,采用CLUE-S模型对未来2030年生态保护情景、自然增长情景以及粮食安全情景的土地利用格局进行了模拟预测,在此基础上采用InVEST模型对流域过去和未来不同情景的生物多样性进行了评估,探讨了流域生物多样性的生境质量和生境退化程度.结果表明：2000~2015年南流江流域建设用地、园地、水域和未利用地呈现出增加趋势,其中建设用地的增幅最大,而耕地和林地减幅最大.流域土地系统中共存在着34种土地网络转移流关系,上游存在24种,中游20种,下游28种,耕地与建设用地、耕地与林地以及林地与园地之间的转换占到流域总土地利用变化的70.74%.CLUE-S模型模拟未来土地利用的Kappa系数达到0.86,表明模型模拟未来情景的土地利用精度满足要求.2000年、2015年、2030年生态保护情景、2030年自然增长情景以及2030年粮食安全情景流域生境质量总得分和平均得分分别为866630,900357,921055,876231,865370和0.7457,0.7747,0.7925,0.7539,0.7466.2030年3种情景的中上游和下游地区生物多样性都呈现出不同程度的改善趋势,而中游地区则表现出退化趋势.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

Aerosol optical properties under different pollution levels in the Pearl River Delta (PRD) region of China

To clarify the aerosol hygroscopic growth and optical properties of the Pearl River Delta(PRD)region,integrated observations were conducted in Heshan City of Guangdong Province from October 19 to November 17,2014.The concentrations and chemical compositions of PM_(2.5),aerosol optical properties and meteorological parameters were measured.The mean value of PM_(2.5) increased from less than 35(excellent) to 35-75 μg/m~3(good) and then to greater than 75 μg/m~3(pollution),corresponding to mean PM_(2.5) values of 24.9,51.2,and 93.3 μg/m~3,respectively.The aerosol scattering hygroscopic growth factor(f(RH = 80%)) values were 2.0,2.12,and 2.18 for the excellent,good,and pollution levels,respectively.The atmospheric extinction coefficient(σext)and the absorption coefficient of aerosols(σ_(ap)) increased,and the single scattering albedo(SSA)decreased from the excellent to the pollution levels.For different air mass sources,under excellent and good levels,the land air mass from northern Heshan had lower f(RH) and σ_(sp) values.In addition,the mixed aerosol from the sea and coastal cities had lower f(RH) and showed that the local sources of coastal cities have higher scattering characteristics in pollution periods.     

Adsorption of 17β-estradiol from aqueous solution by raw and direct/pre/post-KOH treated lotus seedpod biochar

Five biochars derived from lotus seedpod(LSP) were applied to examine and compare the adsorption capacity of 17β-estradiol(E2) from aqueous solution.The effect of KOH activation and the order of activation steps on material properties were discussed.The effect of contact time,initial concentration,p H,ionic strength and humic acid on E2 adsorption were investigated in a batch adsorption process.Experimental results demonstrated that the pseudo second-order model fitted the experimental data best and that adsorption equilibrium was reached within 20 hr.The efficiency of E2 removal increased with increasing E2 concentration and decreased with the increase of ionic strength.E2 adsorption on LSP-derived biochar(BCs) was influenced little by humic acid,and slightly affected by the solution p H when its value ranged from 4.0 to 9.0,but considerably affected at p H 10.0.Low environmental temperature is favorable for E2 adsorption.Chemisorption,π–π interactions,monolayer adsorption and electrostatic interaction are the possible adsorption mechanisms.Comparative studies indicated that KOH activation and the order of activation steps had significant impacts on the material.Post-treated biochar exhibited better adsorption capacity for E2 than direct treated,pretreated,and raw LSP biochar.Pyrolyzed biochar at higher temperature improved E2 removal.The excellent performance of BCs in removing E2 suggested that BCs have potential in E2 treatment and that the biochar directly treated by KOH would be a good choice for the treatment of E2 in aqueous solution,with its advantages of good efficiency and simple technology.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

Ozone pollution characteristics and sensitivity analysis using an observation-based model in Nanjing, Yangtze River Delta Region of China

Ground-level ozone (O₃) has become a critical pollutant impeding air quality improvement in Yangtze River Delta region of China. In this study, we present O₃ pollution characteristics based on one-year online measurements during 2016 at an urban site in Nanjing, Jiangsu Province. Then, the sensitivity of O₃ to its precursors during 2 O₃ pollution episodes in August was analyzed using a box model based on observation (OBM). The relative incremental reactivity (RIR) of hydrocarbons was larger than other precursors, suggesting that hydrocarbons played the dominant role in O₃ formation. The RIR values for NO_X ranged from –0.41%/% to 0.19%/%. The O₃ sensitivity was also analyzed based on relationship of simulated O₃ production rates with reductions of VOC and NO_X derived from scenario analyses. Simulation results illustrate that O₃ formation was between VOCs-limited and transition regime. Xylenes and light alkenes were found to be key species in O₃ formation according to RIR values, and their sources were determined using the Positive Matrix Factorization (PMF) model. Paints and solvent use was the largest contributor to xylenes (54%), while petrochemical industry was the most important source to propene (82%). Discussions on VOCs and NO_X reduction schemes suggest that the 5% O₃ control goal can be achieved by reducing VOCs by 20%. To obtain 10% O₃ control goal, VOCs need to be reduced by 30% with VOCs/NO_X larger than 3:1.     

含油污泥处理技术进展

石油工业生产的特征固体废物——含油污泥,是一种由石油烃、水、固体颗粒物和其他物质（如重金属）组成的固态/半固态复合物,因毒性和易燃性被归入危险废物管理。我国含油污泥年产量高达500万t,其中含有15%~50%的石油烃。含油污泥的处理要兼顾无害化和资源化。基于其组成、性质和危害,介绍了含油污泥的油品资源化分离法（离心、溶剂萃取、热解）和无害化剩余含油残渣处理法（焚烧、固化、生物处理）等国内外常用的处理方法。大体上,含油污泥的处理思路为,首先预处理降低含水率、提高含油率,再经油品分离法回收含油污泥中的石油烃,最后无害化处理剩余含油残渣。讨论了各方法的特点以及国内外研究进展,提出了含油污泥处理技术的发展建议。