Assessment of PCDD/F and PBDD/F emissions from coal-fired power plants during injection of brominated activated carbon for mercury control

The effect of the injection of brominated powdered activated carbon (Br-PAC) on the emission of brominated and chlorinated dioxins and furans in coal combustion flue gas has been evaluated. The sampling campaigns were performed at two U.S. Department of Energy (DOE) demonstration sites where brominated PAC was being injected for control of mercury emissions. The results of the sampling campaigns showed that injection of the brominated PAC upstream of the electrostatic precipitator (ESP) did not increase the emissions of total and Toxic EQuivalent (TEQ) chlorinated and brominated dioxin compounds. Rather, the data suggested the sorbent may capture these compounds and reduce their concentration in the flue gas stream. This effect, when seen, was small, and independent of the type of plant emission controls, temperature at the point of injection, or fuel-chlorine content. The addition of the brominated PAC sorbent resulted in slight increases the total content of chlorinated dioxins and furan in the particulate matter (ash) collected in the ESP, but did not increase its overall toxicity.     

Correlations between homologue concentrations of PCDD/Fs and toxic equivalency values in laboratory-, package boiler-, and field-scale incinerators

The toxic equivalency (TEQ) values of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) are predicted with a model based on the homologue concentrations measured from a laboratory-scale reactor (124 data points), a package boiler (61 data points), and operating municipal waste incinerators (114 data points). Regardless of the three scales and types of equipment, the different temperature profiles, sampling emissions and/or solids (fly ash), and the various chemical and physical properties of the fuels, all the PCDF plots showed highly linear correlations (R(2)>0.99). The fitting lines of the reactor and the boiler data were almost linear with slope of unity, whereas the slope of the municipal waste incinerator data was 0.86, which is caused by higher predicted values for samples with high measured TEQ. The strong correlation also implies that each of the 10 toxic PCDF congeners has a constant concentration relative to its respective total homologue concentration despite a wide range of facility types and combustion conditions. The PCDD plots showed significant scatter and poor linearity, which implies that the relative concentration of PCDD TEQ congeners is more sensitive to variations in reaction conditions than that of the PCDF congeners.     

Open burning of household waste: Effect of experimental condition on combustion quality and emission of PCDD, PCDF and PCB

Open burning for waste disposal is, in many countries, the dominant source of polychlorinated dibenzodioxins, dibenzofurans and biphenyls (PCDD/PCDF/PCB) release to the environment. To generate emission factors for open burning, experimental pile burns of about 100 kg of household waste were conducted with emissions sampling. From these experiments and others conducted by the same authors it is found that less compaction of waste or active mixing during the fire - “stirring” - promotes better combustion (as evidenced by lower CO/CO₂ ratio) and reduces emissions of PCDD/PCDF/PCB; an intuitive but previously undemonstrated result. These experiments also support previous results suggesting PCDD/PCDF/PCB generation in open burning - while still highly variable - tends to be greater in the later (smoldering) phases of burning when the CO/CO₂ ratio increases.     

Emissions of unintentional persistent organic pollutants from open burning of municipal solid waste from developing countries

Open burning of waste is the most significant source of polychlorinated dibenzo-para-dioxins and dibenzofurans (PCDD/PCDF) in many national inventories prepared pursuant to the Stockholm Convention on Persistent Organic Pollutants. This is particularly true for developing countries. Emission factors for POPs such as PCDD/PCDF, dioxin-like polychlorinated biphenyls (dl-PCB) and penta- and hexachlorobenzenes (PeCBz/HCB) from open burning of municipal solid waste in China and Mexico are reported herein. Six different waste sources were studied varying from urban-industrial to semi-urban to rural. For PCDD/PCDF, the emission factors to air ranged from 3.0 to 650 ng TEQ kg⁻¹ waste and for dl-PCB from 0.092 to 54 ng TEQ kg⁻¹ waste. Emission factors for PeCBz (17-1200 ng kg⁻¹ waste) and HCB (24-1300 ng kg⁻¹ waste) spanned a wide but similar range. Within the datasets there is no indication of significant waste composition effect on emission factor with the exception of significantly higher Mexico rural samples.     

Risk Analysis of Invasive Species Introduction in the Port of Arzew,by Calculation of Biofouling Surface on Ships’ Hulls

Historically, the biofouling of ships’ hulls has always been considered amongst the oldest mechanisms causing the introduction of marine invasive species. However, in the last few decades, studies have been oriented mainly towards the introduction of non-indigenous species via ballast water, at the expense of biofouling. In this study, an alternative approach that deals with this latter parameter as the main factor of the introduction of marine organisms is proposed. The biofouling surface area of all vessels which have made call at Arzew port in Algeria is calculated over a period of one year (2014). This parameter indicates the importance of the pressure of propagule that corresponds to the successful introduction effort of a species, since it is this submerged surface of the ship that hosts organisms and spreads them all over the world. We associate to each calculated biofouling surface a bioregion of origin, as well as other parameters such as the number of vessels, their maritime routes and the environmental similarity of Arzew port’s seawater and the other different bioregions. We highlight according to the bioregion, the surfaces that constitute a critical risk of the species introduction and those that constitute a minor risk The study showed that over a period of 1 year, 1313 ships from 28 different bioregions that have made call at Arzew port have accumulated a total wet surface corresponding to about nine million square meters. It is worth to mention that this field of research requires special attention from academics as it may lead to more effective methods to prevent future exotic species introductions.     

Atmospheric trace element concentrations in total suspended particles near Paris,France

To evaluate today’s trace element atmospheric concentrations in large urban areas, an atmospheric survey was carried out for 18 months, from March 2002 to September 2003, in Saclay, nearby Paris. The total suspended particulate matter (TSP) was collected continuously on quartz fibre filters. The TSP contents were determined for 36 elements (including Ag, Bi, Mo and Sb) using two analytical methods: Instrumental Neutron Activation Analysis (INAA) and Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The measured concentrations were in agreement within the uncertainties with the certified values for the polycarbonate reference material filter SRM-2783 (National Institute for Standard Technology NIST, USA). The measured concentrations were significantly lower than the recommended atmospheric concentrations. In 2003, the Pb atmospheric level at Saclay was 15 ng/m³, compared to the 500 ng/m³ guideline level and to the 200 ng/m³ observed value in 1994. The typical urban background TSP values of 1–2, 0.2–1, 4–6, 10–30 and 3–5 ng/m³ for As, Co, Cr, Cu and Sb, respectively, were inferred from this study and were compared with the literature data. The typical urban background TSP concentrations could not be realised for Cd, Pb and Zn, since these air concentrations are highly influenced by local features. The Zn concentrations and Zn/Pb ratio observed in Saclay represented a characteristic fingerprint of the exceptionally large extent of zinc-made roofs in Paris and its suburbs. The traffic-related origin of Ba, Cr, Cu, Pb and Sb was demonstrated, while the atmospheric source(s) of Ag was not identified.     

Effects of a sulfonylurea herbicide on the soil bacterial community

Sulfonylurea herbicides are widely used on a wide range of crops to control weeds. Chevalier® OnePass herbicide is a sulfonylurea herbicide intensively used on cereal crops in Algeria. No information is yet available about the biodegradation of this herbicide or about its effect on the bacterial community of the soil. In this study, we collected an untreated soil sample, and another sample was collected 1 month after treatment with the herbicide. Using a high-resolution melting DNA technique, we have shown that treatment with Chevalier® OnePass herbicide only slightly changed the composition of the whole bacterial community. Two hundred fifty-nine macroscopically different clones were isolated from the untreated and treated soil under both aerobic and microaerobic conditions. The strains were identified by sequencing a conserved fragment of the 16S rRNA gene. The phylogenetic trees constructed using the sequencing results confirmed that the bacterial populations were similar in the two soil samples. Species belonging to the Lysinibacillus, Bacillus, Pseudomonas, and Paenibacillus genera were the most abundant species found. Surprisingly, we found that among ten strains isolated from the treated soil, only six were resistant to the herbicide. Furthermore, bacterial overlay experiments showed that only one resistant strain (related to Stenotrophomonas maltophilia) allowed all the sensitive strains tested to grow in the presence of the herbicide. The other resistant strains allowed only certain sensitive strains to grow. On the basis of these results, we propose that there must be several biodegradation pathways for this sulfonylurea herbicide.     

Emissions of PCDD and PCDF from combustion of forest fuels and sugarcane: a comparison between field measurements and simulations in a laboratory burn facility

Release of PCDD and PCDF from biomass combustion such as forest and agricultural crop fires has been nominated as an important source for these chemicals despite minimal characterisation. Available emission factors that have been experimentally determined in laboratory and field experiments vary by several orders of magnitude from <0.5 μg TEQ (t fuel consumed)⁻¹ to >100 μg TEQ (t fuel consumed)⁻¹. The aim of this study was to evaluate the effect of experimental methods on the emission factor.A portable field sampler was used to measure PCDD/PCDF emissions from forest fires and the same fuel when burnt over a brick hearth to eliminate potential soil effects. A laboratory burn facility was used to sample emissions from the same fuels. There was very good agreement in emission factors to air (EF_Air) for forest fuel (Duke Forest, NC) of 0.52 (range: 0.40-0.79), 0.59 (range: 0.18-1.2) and 0.75 (range: 0.27-1.2) μg TEQ_WHO2005 (t fuel consumed)⁻¹ for the in-field, over a brick hearth, and burn facility experiments, respectively. Similarly, experiments with sugarcane showed very good agreement with EF_Air of 1.1 (range: 0.40-2.2), 1.5 (range: 0.84-2.2) and 1.7 (range: 0.34-4.4) μg TEQ (t fuel consumed)⁻¹ for in-field, over a brick hearth, open field and burn facility experiments respectively. Field sampling and laboratory simulations were in good agreement, and no significant changes in emissions of PCDD/PCDF could be attributed to fuel storage and transport to laboratory test facilities.     

Verification results of jet resonance-enhanced multiphoton ionization as a real-time PCDD/F emission monitor

A jet resonance-enhanced multiphoton ionization (REMPI) monitor was tested on a hazardous-waste-fired boiler for its ability to determine concentrations of polychlorinated dibenzodioxins and dibenzofurans (PCDDs/Fs). Jet REMPI is a real-time instrument capable of highly selective and sensitive (from parts per billion to parts per trillion) detection of a broad range of aromatic compounds, including a number of air toxic compounds. The PCDD/F toxic equivalency (TEQ) value was derived from a predetermined correlation (R ² = 0.74) with monochlorobenzene (MClBz). This relationship was applied to nine subsequent jet REMPI on-line measurements of MClBz and parallel, standard extractive sampling for PCDD/F TEQ. For high waste-firing rates, with a range of PCDD/F TEQ values between 3.9 and 6.0 ng TEQ/m³, the TEQ values predicted by jet REMPI had a relative difference of 26% with the standard EPA Method 23 results. At low waste-firing rates (0.9–1.6 ng TEQ/m³), the relative difference increased to 219%. This limited testing shows that jet REMPI has promise as an on-line diagnostic monitor, providing feedback on the effects on PCDD/F emissions of operating parameter changes such as fuel feed interruptions or air pollution control failures.