Estimating population abundance using counts from an auxiliary population

Environmental and Ecological Statistics - We develop a new method for estimating population abundance for notoriously difficult to count populations. This is made possible using an easy to count...     

Ambient and household air pollution on early-life determinants of stunting—a systematic review and meta-analysis

Environmental Science and Pollution Research - Stunting is an important risk factor for early growth and health implications throughout the life course, yet until recently, studies have rarely...     

Comparisons of soil surface sealing methods to reduce fumigant emission loss

State and federal regulatory agencies depend on quality field data for determining the effects of agricultural management practices on fumigant emissions to develop sound, science-based policies and regulations on preplant soil fumigants. Field plot tests, using growers' standard field operation procedures, were used to simultaneously determine the effectiveness of several commonly proposed emission reduction methods, in a trial involving shank injection of Telone II [a.i. 1,3-dichloropropnene (1,3-D)] to a sandy loam soil to a target rate of 372 kg ha(-1). The experiment was conducted in late September 2008 in the San Joaquin Valley of California. Fumigant emissions were captured using dynamic flux chambers. The results showed that virtually impermeable film (VIF) reduced emissions >95% when compared to bare soil, and the glue joints in the film did not significantly affect the tarp performance. The VIF also created a more uniform distribution of gaseous fumigant in the soil profile, which would likely benefit pest control efficacy. Standard high-density polyethylene (HDPE) tarp reduced total 1,3-D emissions about 50% (higher than most reported values) in this trial, whereas postfumigation intermittent water treatments (seals) reduced cumulative emission losses by approximately 20%. Adding 49.4 Mg ha (equivalent to 20 tons per acre) of composted dairy manure to surface soils did not reduce 1,3-D emissions during this experiment. Use of VIF was the most promising technique in reducing emissions and has the potential to allow lower application rates while providing satisfactory pest control.     

Successful early in utero management of fetal hydrothorax in a twin pregnancy

We present a case of dichorionic diamniotic twin pregnancy in which one of the fetuses was found to have a major pleural effusion at 15 weeks of gestation. A single-needle pleural fluid aspiration was performed at 15 and 16 weeks, but the fluid reaccumulated quickly after each procedure and at 16 weeks, the fetus was found to become progressively hydropic. A shunt was then successfully inserted at 17 weeks, which is the earliest gestation reported so far in the literature for such a procedure to treat isolated hydrothorax. Because we felt that the fetus would be too small for a classical double-pigtail pleuroamniotic shunt, we used a multilength double-pigtail bladder stent (Harrison drain; Cook; Spencer; Indiana; USA) via a 13-gauge echo tip trocar. This shunt could be used for both singleton and twin pregnancies presenting with fetal pleural effusion from as early as 16 to 17 weeks to prevent the development of fetal hydrops and polyhydramnios and subsequent premature delivery. Treatment at this stage of gestation would also minimize the risk of lung hypoplasia, which is the main clinical issue when shunts are inserted after 24 weeks. Copyright © 2003 John Wiley & Sons, Ltd.     

EKC analysis for studying economic growth and environmental quality: a case study in China

Compared with the extensive research on the relationship between economic growth and environmental quality in developed countries, there is a paucity of an empirical research on studying the relation for developing countries. Based upon the Environmental Kuznets Curve (EKC) theory, this paper develops regression models for investigating the relationship between economic growth and environmental quality in China. The EKC analysis based on six pollution indices is illustrated with a case study in Jiaxing of Zhejiang, China.     

Spray atomization characteristics as a function of pesticide formulations and atomizer design

Abstract

The use of formulation adjuvants to increase the drop size of pesticide sprays has followed a practice which has evolved through many years of experimentation and development. The earliest materials used were simply designed to make the spray mix viscous on the premise that a mayonnaise‐like fluid would produce larger drops and hence increase the deposit efficiency. These viscomer materials, emulsions and water soluble thickeners such as starch and agars, as well as more complex cellulose materials, produced thick non‐Newtonian fluids which were difficult to mix, pump and spray, and provided questionable results. First, the larger drops reduced target coverage from a given volume of spray; and second, field tests with these definitely showed that a large volume of small drops were still being produced even with the thickest of formulations.

The next step in adjuvant evolution was the introduction of polyvinyl, polyacrylamide and polyamide elastomer materials. These polymers are also non‐Newtonian, but due to their peculiar molecular bonding, they have the capability of forming long string‐like streams which when atomized can retract into a spray of large drops. Pure forms of these polymers are blended by commercial producers to enable compatibility with pesticide chemicals. We have conducted a series of laboratory and wind tunnel tests; first, to try and establish some physical parameters identifying their characteristics and second, to determine how these adjuvants affect atomization and the production of small drift‐prone drops (i.e., those smaller than 120 μm in diameter).

Our results with the laboratory studies of physical properties and of the wind tunnel drop size tests have been inconclusive. The elastomer materials have relatively low viscosity (1.5 to 6 mPa.s) and reduced surface tension (50 to 60 mN/m) but our stream‐flow extension tests were non‐productive. The drop size studies comparing water sprays with polymer‐water mixtures gave us a mixed picture. Generally drop size was increased for all of the fan (deflector and milled orifice) and cone type atomizers. But an increase was also indicated of the volume of spray in drops less than 120 μm showing that the polymer did not fully control the production of these small drops under all of the testing procedures we studied.

It is difficult to evaluate the capability of these additives for controlling or reducing production of the drift‐prone small drops. While the pure solutions of the water soluble polymers would appear to be capable of this desirable effect, it is also evident that in order to make these formulations compatible with pesticide spray solutions, several other solvents, emulsifiers and surface active chemicals are added to the formulation, thus affecting the atomization characteristics and hence their drift‐control capability.