Influence of floc dynamic protection layer on alleviating ultrafiltration membrane fouling induced by humic substances

Cake layer formation is inevitable over time for ultrafiltration (UF) membrane-based drinking water treatment. Although the cake layer is always considered to cause membrane fouling, it can also act as a “dynamic protection layer”, as it further adsorbs pollutants and dramatically reduces their chance of getting to the membrane surface. Here, the UF membrane fouling performance was investigated with pre-deposited loose flocs in the presence of humic acid (HA). The results showed that the floc dynamic protection layer played an important role in removing HA. The higher the solution pH, the more negative the floc charge, resulting in lower HA removal efficiency due to the electrostatic repulsion and large pore size of the floc layer. With decreasing solution pH, a positively charged floc dynamic protection layer was formed, and more HA molecules were adsorbed. The potential reasons were ascribed to the smaller floc size, greater positive charge, and higher roughness of the floc layer. However, similar membrane fouling performance was also observed for the negative and positive floc dynamic protection layers due to their strong looseness characteristics. In addition, the molecular weight (MW) distribution of HA also played an important role in UF membrane fouling behavior. For the small MW HA molecules, the chance of forming a loose cake layer was high with a negatively charged floc dynamic protection layer, while for the large MW HA molecules it was high with a positively charged floc dynamic protection layer. As a result, slight UF membrane fouling was induced.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Effect of NOx and SO2 on the photooxidation of methylglyoxal: Implications in secondary aerosol formation

Methylglyoxal(CH_3COCHO,MG),which is one of the most abundant α-dicarbonyl compounds in the atmosphere,has been reported as a major source of secondary organic aerosol(SOA).In this work,the reaction of MG with hydroxyl radicals was studied in a 500 L smog chamber at(293±3) K,atmospheric pressure,(18±2)% relative humidity,and under different NOx and SO_2.Particle size distribution was measured by using a scanning mobility particle sizer(SMPS) and the results showed that the addition of SO_2 can promote SOA formation,while different NOx concentrations have different influences on SOA production.High NOx suppressed the SOA formation,whereas the particle mass concentration,particle number concentration and particle geometric mean diameter increased with the increasing NOx concentration at low NOx concentration in the presence of SO_2.In addition,the products of the OH-initiated oxidation of MG and the functional groups of the particle phase in the MG/OH/SO_2 and MG/OH/NOx/SO_2 reaction systems were detected by gas chromatography mass spectrometry(GC-MS) and attenuated total reflection fourier transformed infrared spectroscopy(ATR-FTIR) analysis.Two products,glyoxylic acid and oxalic acid,were detected by GC-MS.The mechanism of the reaction of MG and OH radicals that follows two main pathways,H atom abstraction and hydration,is proposed.Evidence is provided for the formation of organic nitrates and organic sulfate in particle phase from IR spectra.Incorporation of NOx and SO_2 influence suggested that SOA formation from anthropogenic hydrocarbons may be more efficient in polluted environment.     

Will polycentric cities cause more CO2 emissions? A case study of 232 Chinese cities

From 2000 to 2010 China experienced rapid economic development and urbanization. Many cities in economically developed areas have developed from a single-center status to polycentricity. In this study, we used exploratory spatial data analysis (ESDA) to identify the population centers, which identified 232 cities in China as having urban centers. COMP was used to represent urban agglomeration, and POLYD (representing how far is the city's sub-centers to the main center), POLYC (representing the number of a city's centers), and POLYP (representing the population distributed between the main center and the sub-centers) were used to indicate urban polycentricity. Night light data were used to determine the CO₂ emissions from various cities in China. A mixed model was used to study the impact of urban aggregation and polycentric data on the CO₂ emission efficiency in 2000 and 2010. The study found that cities with higher compactness were distributed in coastal areas, and the cities with higher multicentricity were distributed in the Yangtze River Delta and Shandong Province. The more compact the city was, the less conducive it was to improving CO₂ emission efficiency. Polycentric development of the city was conducive to improving the CO₂ emission efficiency, but the number of urban centers had no significant relationship with the CO₂ emission efficiency. Our research showed that the compactness and multicentricity of the city had an impact on the CO₂ emission efficiency and provided some planning suggestions for the low carbon development of the city.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Concentrations and chemical compositions of PM10 during hazy and non-hazy days in Beijing

In order to study the concentrations of major components,characteristics and comparison in hazy and non-hazy days of PM_(10) in Beijing,aerosol samples were collected at urban site in Beijing from December 29,2014 to January 22,2015.Heavy metals like Zn,Pb,Mn,Cu,As,V,Cr and Cd were deeply studied considering their toxic effects on human being;nine water-soluble inorganic ions(SO_4~(2-),NO_3~-,NH_4~+,Na~+,K~+,Cl~-,Ca~(2+) and Mg~(2+)) and carbon fractions(OC and EC) were also analyzed.The concentrations of heavy metals were 1.03–1.98 times higher in hazy days than those in non-hazy days,mainly due to biomass burning and coal burning.The trends in total heavy metals concentrations were basically consistent with the trends in PM concentrations except for two obvious periods(12.29–12.30;1.14–1.15);but when air masses accumulated locally or around Beijing,trends in PM concentrations and heavy metals were opposite.The proportion for NO_3~-/SO_4~(2-) indicated that mobile sources such as automobiles were important reasons for haze in Beijing.Correlation between OC and EC during non-hazy days was strong(R~2= 0.95) but it was low(R~2= 0.67) during hazy days,and large variations for OC/EC values occurred in hazy days.The calculated mass concentration of SOC is 2.58 μg/m~3,which only accounted for 10.1% of the OC concentration.When air masses from the far north-west,they decreased PM concentration in Beijing and they were relatively clean;however,those from the near east,south-east and south of the mainland increased PM concentration and they were dirty.     

Well-to-wheels greenhouse gas and air pollutant emissions from battery electric vehicles in China

Mitigation and Adaptation Strategies for Global Change - Electric vehicles (EVs) play a crucial role in addressing climate change and urban air quality concerns. China has emerged as the global...     

Optimal range of plug-in electric vehicles in Beijing and Shanghai

Both China’s national subsidy policies for plug-in electric vehicles (PEVs) purchasers and passenger cars corporate average fuel consumption and new vehicle credit regulation (dual-credit policy) favor long-range 300+ km battery electric vehicles (BEVs) and 80+ km plug-in hybrid electric vehicles (PHEVs). However, these electric vehicles tend to have lower energy efficiency and higher purchase and operation costs. Vehicle with larger batteries can also be less equitable because the subsidies are often provided to more expensive vehicles and wealthier owners. This study takes advantage of a novel dataset of daily driving data from 39,854 conventional gasoline vehicles in Beijing and 4999 PHEVs in Shanghai to determine the optimal range of BEVs and PHEVs within their respective cities. We simulate a model to explore ranges with which PEVs emit less GHGs than that of a baseline hybrid and conventional gasoline vehicle while ensuring that all daily travel demands are met. Our findings indicate that in both cities, the optimal ranges to balance cost and travel demand for BEVs are 350 km or less and for PHEVs are 60 km or less in Beijing and 80 km or less in Shanghai. We also find that to minimize carbon dioxide (CO₂) emissions, the ranges are even lower 10 km in Beijing and 30 km in Shanghai. Our study suggests that instead of encouraging long-range PEVs, governments should subsidize PEV models with shorter ranges. Parallel efforts should also be made to both increase renewable energy over fossil fuels and expand charging facilities. Although individual mobility demand varies, the government could reduce occasional long-distance driving by subsidizing alternative transportation choices. Providing week-long driving trials to consumers before their purchases may help decrease the demand of very long range PEVs by alleviating the range anxiety through a learning process.

     

Green innovation efficiency across China’s 30 provinces: estimate,comparison, and convergence

Mitigation and Adaptation Strategies for Global Change - Considering government and market failure of environmental regulation to combat increasing GHG (greenhouse gas) emissions, green innovation...     

Relationship between physicochemical properties and dewaterability of hydrothermal sludge derived from different source

Sewage sludge (SS) and deinking sludge (DS) were used to comparatively study the hydrothermal dewatering of sludge with different components. For a better overview, an insight into the relationship between physicochemical properties and dewaterability of hydrothermal sludge was provided. Results found that not all kinds of sludge were suitably conditioned by hydrothermal treatment (HT) in term of the elevation of dewaterability. Higher hydrothermal temperature tended to enhance the dewaterability of SS rather than DS, which was supported by the variation of their physicochemical properties (including water distribution, bonding energy, extracellular polymeric substance (EPS), particles size, acid functional groups and zeta potential in this study). In addition, the changes in surface morphology suggested that the reverse effect of HT on sludge dewaterability was mainly due to their dewatering behavior. For SS, the destruction of EPS structure leaded to the release of bound water, thereby strengthening sludge dewatering. Conversely, “Bridging effect” generated by lignocellulose in DS was beneficial for sludge dewatering; however, the increasing hydrothermal temperature degraded part of lignocellulose and weakened “bridging effect”, finally resulting in worse dewaterability of DS.