Influences of chemical activators on incinerator bottom ash

This research has applied different chemical activators to mechanically and thermally treated fine fraction (<14 mm) of incinerator bottom ash (IBA), in order to investigate the influences of chemical activators on this new pozzolanic material. IBA has been milled and thermally treated at 800 degrees C (TIBA). The TIBA produced was blended with Ca(OH)(2) and evaluated for setting time, reactivity and compressive strength after the addition of 0.0565 mole of Na(2)SO(4), K(2)SO(4), Na(2)CO(3), K(2)CO(3), NaOH, KOH and CaCl(2) into 100g of binder (TIBA+Ca(OH)(2)). The microstructures of activated IBA and hydrated samples have been characterized by X-ray diffraction (XRD) and thermogravimetry (TG) analysis. Thermal treatment is found to produce gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)) phases. The thermally treated IBA samples are significantly more reactive than the milled IBA. The addition of Na(2)CO(3) can increase the compressive strength and calcium hydroxide consumption at 28-day curing ages. However, the addition of Na(2)SO(4), K(2)SO(4), K(2)CO(3), NaOH and KOH reduces the strength and hydration reaction. Moreover, these chemicals produce more porous samples due to increased generation of hydrogen gas. The addition of CaCl(2) has a negative effect on the hydration of TIBA samples. Calcium aluminium oxide carbonate sulphide hydrate (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33)(H(2)O)(11)) is the main hydration product in the samples with activated IBA, except for the sample containing CaCl(2).     

Modeling the fate of benzo[a]pyrene in the wastewater-irrigated areas of Tianjin with a fugacity model

A Level III fugacity model was applied to characterize the transfer processes and environmental fate of benzo[a]pyrene in wastewater-irrigated areas of Tianjin, China. The physical-chemical properties and transfer parameters of benzo[a]pyrene were used in the model and the concentration distribution of benzo[a]pyrene in sediment, soil, water, air, fish, and crop compartments, as well as transfer fluxes across the compartments, were then derived under steady-state assumptions. The calculated results were compared with monitoring data for air, soil, water, and sediment collected from the literature. The results indicate that there was generally good agreement and the differences were within an order of magnitude for air, soil, and sediment. The concentration of benzo[a]pyrene in the ambient air in the area was very low with a majority present sorbed to aerosol. In the water compartment, approximately 70% of benzo[a]pyrene dissolved in water phase. Relatively high concentrations of the compound were found in the soil and sediment, with the soil serving as the dominant sink in the area. Benzo[a]pyrene, with a slow metabolic rate, was found to accumulate in fish in the area.     

Highlights and new Editorial Advisory Board members of the Journal of Environmental Sciences

正The Journal of Environmental Sciences(JES)is honored to welcome Professors/Drs William A.Mitch,Jiuhui Qu,Susan D.Richardson,Jerald L.Schnoor,Hongxiao Tang,Shu Tao,and Hugh A.Tilson to serve on the Editorial Advisory Board(EAB).Their tremendous experience in scientific publications,leading expertise in topic areas pertinent to JES,diverse international networks/perspectives,and exemplary dedication to scientific excellence will guide and help the continuing healthy growth of JES.     

Inexact fuzzy-stochastic constraint-softened programming – A case study for waste management

In this study, an inexact fuzzy-stochastic constraint-softened programming method is developed for municipal solid waste (MSW) management under uncertainty. The developed method can deal with multiple uncertainties presented in terms of fuzzy sets, interval values and random variables. Moreover, a number of violation levels for the system constraints are allowed. This is realized through introduction of violation variables to soften system constraints, such that the model’s decision space can be expanded under demanding conditions. This can help generate a range of decision alternatives under various conditions, allowing in-depth analyses of tradeoffs among economic objective, satisfaction degree, and constraint-violation risk. The developed method is applied to a case study of planning a MSW management system. The uncertain and dynamic information can be incorporated within a multi-layer scenario tree; revised decisions are permitted in each time period based on the realized values of uncertain events. Solutions associated with different satisfaction degree levels have been generated, corresponding to different constraint-violation risks. They are useful for supporting decisions of waste flow allocation and system-capacity expansion within a multistage context.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

Monitoring method for airborne glymes and its application in fuel exhaust emission measurement.

A monitoring method based on solvent extraction of adsorbed target glymes followed by gas chromatograph-mass spectrometry GC-MS analysis was developed for seven glymes, namely ethylene glycol dimethyl ether, propylene glycol dimethyl ether, ethylene glycol diethyl ether, diethylene glycol dimethyl ether, diethylene glycol diethyl ether, triethylene glycol dimethyl ether, and tetraethylene glycol dimethyl ether. The best recoveries of target glymes were achieved when using a combination of sample collection medium of graphitised carbon black (GCB) with a solvent mixture of methylene chloride and methanol (95/5, v/v). Method detection limits ranged from 1.5 microg/m3 for diethylene glycol diethyl ether to 13.2 microg/m3 for ethylene glycol diethyl ether based on a sample volume of 3.4 1. Using this method, diethylene glycol dimethyl ether and diethylene glycol diethyl ether were detected and measured successfully in diluted vehicle exhausts in diesel fuel engine tests.     

Feeding and respiration rates of a planktonic copepod (<Emphasis Type="Italic">Calanus sinicus</Emphasis>) oversummering in Yellow Sea Cold Bottom Waters

The distribution, feeding and oxygen consumption of Calanus sinicus were studied in August 2001 on a transect across Yellow Sea Cold Bottom Waters (YSCBW) and two additional transects nearby. The distribution of C. sinicus adults and copepodites stage CV appeared to be well correlated with water temperature. They tended to concentrate in the YSCBW (>10,000 ind. m^–2) to avoid high surface temperature. Gut pigment contents varied from 0.44 to 2.53 ng chlorophyll a equivalents (chl a equiv.) ind.^–1 for adults, and from 0.24 to 2.24 ng chl a equiv. ind.^–1 for CV copepodites. We found no relationship between gut pigment contents and the ambient chl a concentrations. Although the gut evacuation rate constants are consistent with those measured for other copepods, their low gut pigment contents meant an estimated daily herbivorous ingestion of <3% of body carbon in the YSCBW and <10% outside the YSCBW. However, based on estimates of clearance rates, C. sinicus feeds actively whether in the YSCBW or not, so the low ingestion rates probably reflect shortage of food. Oxygen consumption rates of C. sinicus ranged from 0.21 to 0.84 l O₂ ind.^–1 h^–1, with high rates often associated with high temperature. From the oxygen consumption rates, daily loss of body carbon was estimated to be 4.0–13.7%, which exceeds our estimates of their carbon ingestion rates. C. sinicus was probably not in diapause, either within or outside the YSCBW, but this cold-water layer provides C. sinicus with a refuge to live through the hot, low-food summer.Communicated by T. Ikeda, Hakodate     

Female sex pheromone of Ostrinia orientalis – throwing a light on the relationship between O. orientalis and the European corn borer, O. nubilalis

Summary. The sex pheromone of Ostrinia orientalis (Lepidoptera: Crambidae) was analyzed by gas chromatography–electroantennographic detection (GC–EAD), GC–mass spectrometry and a series of bioassays. Three EAD-active compounds were detected in the female sex pheromone gland extract, and identified as tetradecyl acetate (14:OAc), (Z)-11-tetradecenyl acetate (Z11-14:OAc) and (E)-11-tetradecenyl acetate (E11-14:OAc). The titers (ratio) of 14:OAc, Z11-14:OAc and E11-14:OAc in 3-day-old virgin females were 0.49 ng (10), 4.86 ng (98) and 0.10 ng (2), respectively. In a wind-tunnel bioassay, the 98:2 blend of Z11- and E11-14:OAc, but not Z11-14:OAc alone, elicited the same male behavioral responses as virgin females and crude gland extracts. 14:OAc was inactive by itself, and did not show any synergistic effect on the binary blend. Field trapping experiments also confirmed the attractiveness of the binary blend to O. orientalis males. Based on these results, we concluded that the sex pheromone of O. orientalis is a 98:2 mixture of Z11-14:OAc and E11-14:OAc. This sex pheromone is very similar to that of the Z-type European corn borer, O. nubilalis. The present finding raises the question of whether O. orientalis , which is indistinguishable from O. nubilalis based on external morphology, is a biologically distinct species independent from O. nubilalis.     

Irrigation model of bleached Kraft mill wastewater through volcanic soil as a pollutants attenuation process

An irrigation process through volcanic soil columns was evaluated for bleached Kraft mill effluent pollutants retention. The system was designed to remove color and phenolic compounds and a simple kinetic model for determining the global mass transfer coefficient and the adsorption rate constant was used. The results clearly indicate that the global mass transfer coefficient values (K(c)a) and the adsorption rate constants are higher for the irrigation processes onto acidified soil. This means that the pretreatment of washing the volcanic soil with an acid solution has a positive effect on the adsorption rate for both pollutant groups. The enhanced adsorption capacity is partially explained by the activation of the metal oxides present in the soil matrix during the acid washing process. Increasing the flow rate from 1.5 to 2.5 ml/min yielded higher (K(c)a) values and adsorption rate constants for both pollutant groups. For instance, regarding color adsorption onto acidified soil, there is an increment of 43% in the (K(c)a) value for the experiment with a flow rate of 2.5 ml/min. Increasing the porosity of the column from 0.55 to 0.59, yielded a decrease in the (K(c)a) values for color and phenolic compounds adsorption processes. Onto natural soil for example, these decreases reached 21% and 24%, respectively. Therefore, the (K(c)a) value is dependent on both the liquid-phase velocity (external resistance) and the soil fraction in the column (internal resistance); making forced convection and diffusion to be the main transport mechanisms involved in the adsorption process. Analyzing the adsorption rate constants (K(c)a)/m, phenolic compounds and color adsorption rates onto acidified soil of 2.25 x 10(-6) and 2.62 x 10(-6) l/mg min were achieved for experiment 1. These adsorption rates are comparable with other adsorption systems and adsorbent materials.     

Joint analysis of process and operator performance in chemical process operational safety

Independent studies of case histories by the Health and Safety Commission in the UK and by a Honeywell led industrial consortium world-wide showed that human errors represent the major cause of failure in process plant operation. In contrast to this discovery the majority of previous studies on computer aided systems for fault detection and diagnosis has focused on the process side. This paper presents a methodology, which can involve human factors into the development of systems for automatic identification and diagnosis of abnormal operations and develops methods and techniques that can be used to simultaneously capture, characterise and assess the performance of operators as well as of the process. A joint process–operator simulation platform is developed which is used as a test-bed for carrying out the study. The process part is a simulator, which simulates in high fidelity the dynamic behaviour of the process that is subject to the influence of various disturbances and operators’ interventions. The operator module is developed as a real-time expert system, which emulates operator’s behaviour in interpretation of received signals, and planning and execution of decisions. The interaction between the two modules is managed through an interaction module, which handles the real-time exchange of data using Dynamic Data Exchange. The interaction module also contains the toolkits for analysing the dynamic behaviour of the joint process–operator system. The method and system are illustrated using a simulated case study.