Investigation of titanium liquid/gas diffusion layers in proton exchange membrane electrolyzer cells

In a proton exchange membrane electrolyzer cell (PEMEC), liquid/gas diffusion layer (LGDL) is expected to transport electrons, heat, and reactants/products to and from the catalyst layer with minimum voltage, current, thermal, interfacial, and fluidic losses. In addition, carbon materials, which are typically used in PEM fuel cells (PEMFCs), are unsuitable in PEMECs due to the high ohmic potential and highly oxidative environment of the oxygen electrode. In this study, a set of titanium gas diffusion layers with different thicknesses and porosities are designed and examined coupled with the development of a robust titanium bipolar plate. It has been found that the performance of electrolyzer improves along with a decrease in thickness or porosity of the anode LGDL of titanium woven meshes. The ohmic resistance of anode LGDL and contact resistance between anode LGDL and the anode catalyst play dominant roles in electrolyzer performance, and better performance can be obtained by reducing ohmic resistance. Thin titanium LGDLs with straight-through pores and optimal pore morphologies are recommended for the future developments of low-cost LGDLs with minimum ohmic/transport losses.     

改性膨润土联合混凝剂处理微污染水中有机物

采用十二烷基多糖苷季铵盐作为改性剂制备改性膨润土,研究了改性膨润土联合混凝剂去除有机物的效果,考察了有机改性剂用量、微波辐射功率、辐射时间、膨润土投加量、pH值对有机物去除效果的影响,探讨了改性膨润土的改性和去除机理。结果表明,经微波改性后,实现了十二烷基多糖苷季铵盐阳离子对膨润土的插层,增大了层间距,提高了膨润土的吸附性能。联合混凝剂投加改性膨润土能够改善絮凝性能,显著提高有机物的去除效果。在最佳条件下,改性膨润土与PAC联合后的强化混凝,对初始浓度15.3 mg/L的微污染水中有机物的去除率达到95%以上,吸附符合Freundlich吸附等温方程。     

煤粉炉掺烧干化污泥的污染物排放研究

结合某电厂420 t/h四角煤粉炉掺烧污泥项目的实验室分析测试,了解煤粉掺烧不同含水率不同比例的干化污泥条件下烟气中污染物和灰渣中重金属的排放特性。结果表明,在实验研究配比和燃烧的条件下,大部分重金属元素Pb、Cu、Cr和Ni残留在灰渣中,Zn、Cd部分残留在灰渣中,As、Hg和Se等易挥发元素释放到烟气中,在灰渣中的含量很小。掺烧污泥后,灰渣中的重金属含量较单烧单煤都有了一定幅度的升高,Zn的含量是单煤的2倍,其余重金属是单煤的1.1~1.2倍。3种不同的掺混比例之间的污染气体排放浓度基本相似。烟气中主要污染物及重金属浓度可以满足现行国家标准。与单烧单煤相比,CO、HCl以及其他有机气体排放浓度基本相同;NH3的排放浓度较单煤有所升高;SO2、NOx和CO2排放浓度略有降低;飞灰浓度有所升高。烟气中的重金属,Hg含量升高了30%,Pb含量约为单煤的4.3~4.8倍。以上研究结果可为环保达标和飞灰利用提供基础数据。     

改性SiO2气凝胶对废水中Fe3+的吸附性能

制备了改性SiO₂气凝胶,考察了经不同类型、不同配比的改性剂改性的SiO₂气凝胶对模拟含Fe³⁺废水的吸附处理效果。实验结果表明：改性SiO₂气凝胶的最佳制备条件为三甲基氯硅烷（TMCS）作改性剂,V（TMCS）#x02236;V（正己烷）=1#x02236;5;当改性SiO₂气凝胶加入量为75g/L、吸附时间为4h、Fe³⁺质量浓度为10mg/L时,模拟含Fe³⁺废水的Fe³⁺去除率为98.32%,剩余Fe³⁺质量浓度为0.168mg/L;采用改性SiO₂气凝胶动态吸附处理流量为420mL/h、Fe³⁺质量浓度为100mg/L的模拟含Fe³⁺废水,吸附后废水中剩余Fe³⁺质量浓度仅为0.196mg/L。     

An overview on the processes and technologies for recycling cathodic active materials from spent lithium-ion batteries

This paper aims to make an overview on the current status and new tendency for recycling cathodic active materials from spent lithium-ion batteries. Firstly, it introduces several kinds of pretreatment technologies, followed by the summary of all kinds of single recycling processes mainly focusing on organic acid leaching and synergistic extraction. Then, several examples of typical combined processes and industrial recycling processes are presented in detail. Meanwhile, the advantages, disadvantages and prospect of each single process, combined process, as well as industrial recycling processes, are discussed. Finally, based on a novel acidic organic solvent, the authors briefly introduce an environmental friendly process to directly recycle and resynthesize cathodic active material LiNi_1/3Co_1/3Mn_1/3O₂ from spent lithium-ion batteries. The preliminary experimental results demonstrated the advantages of low reaction temperature, high separation efficiency and organic solvent cycling and preventing secondary pollution to the environment. This process may be used for large-scale recycling of spent lithium-ion batteries after further study.     

锰矿区土-水界面污染流中重金属来源分析

基于对湘潭锰矿红旗矿区土-水界面重金属污染流的采样分析,通过相关性和主成分分析法,研究了锰矿区土-水界面重金属污染流中的锰、镍、铜、锌、镉、铅重金属的来源以及同源性。结果表明:6种重金属的差异性、离散程度、变异性较大;锰—镍、锰—锌、锰—镉、锰—铅、镍—锌、铜—锌、铜—铅、锌—镉、锌—铅、铅—镉呈极显著正相关,镍与锰以外的其他重金属相关性都较低;3个主成分的贡献率分别为58.300%、16.628%、11.115%,累积贡献率达到了81.543%,并且6种重金属在主成分1的载荷非常高。结合矿区的周边环境和自身特点,表明6种重金属的主要共同来源为矿区内的矿业活动,并且工业活动、交通运输、农业活动等也对矿区造成了一定程度的重金属污染。     

模拟阳光下Ag／I-TiO2光催化预处理山核桃加工废水

研究了在模拟太阳光下,采用银修饰的碘掺杂二氧化钛光催化剂（Ag／I—TiO2）对某食品厂山核桃加工废水进行光催化预处理的效果。结合x射线衍射（XRD）、比表面积分析（BET）、紫外-可见漫反射光谱（uV—Vis）的表征结果,来分析催化剂结构对于废水处理效果的影响。探讨了Ag含量、废水初始pH（pHi）和光照时间等因素对化学需氧量（COD）去除及水质可生化性（B／C）提高的影响。并得出适宜的反应参数为：3％Ag含量;pHi为6;光照时间为240min。在最佳条件下,COD去除率45％,废水B／C比由0．17上升到0．31。光催化氧化法能够有效降低山核桃加工废水的COD含量,并达到显著提高废水可生化性的目的。     

Estimating and comparing greenhouse gas emissions with their uncertainties using different methods: A case study for an energy supply utility

Energy supply utilities release significant amounts of greenhouse gases (GHGs) into the atmosphere. It is essential to accurately estimate GHG emissions with their uncertainties, for reducing GHG emissions and mitigating climate change. GHG emissions can be calculated by an activity-based method (i.e., fuel consumption) and continuous emission measurement (CEM). In this study, GHG emissions such as CO₂, CH₄, and N₂O are estimated for a heat generation utility, which uses bituminous coal as fuel, by applying both the activity-based method and CEM. CO₂ emissions by the activity-based method are 12–19% less than that by the CEM, while N₂O and CH₄ emissions by the activity-based method are two orders of magnitude and 60% less than those by the CEM, respectively. Comparing GHG emissions (as CO₂ equivalent) from both methods, total GHG emissions by the activity-based methods are 12–27% lower than that by the CEM, as CO₂ and N₂O emissions are lower than those by the CEM. Results from uncertainty estimation show that uncertainties in the GHG emissions by the activity-based methods range from 3.4% to about 20%, from 67% to 900%, and from about 70% to about 200% for CO₂, N₂O, and CH₄, respectively, while uncertainties in the GHG emissions by the CEM range from 4% to 4.5%. For the activity-based methods, an uncertainty in the Intergovernmental Panel on Climate Change (IPCC) default net calorific value (NCV) is the major uncertainty contributor to CO₂ emissions, while an uncertainty in the IPCC default emission factor is the major uncertainty contributor to CH₄ and N₂O emissions. For the CEM, an uncertainty in volumetric flow measurement, especially for the distribution of the volumetric flow rate in a stack, is the major uncertainty contributor to all GHG emissions, while uncertainties in concentration measurements contribute a little to uncertainties in the GHG emissions.

Implications:Energy supply utilities contribute a significant portion of the global greenhouse gas (GHG) emissions. It is important to accurately estimate GHG emissions with their uncertainties for reducing GHG emissions and mitigating climate change. GHG emissions can be estimated by an activity-based method and by continuous emission measurement (CEM), yet little study has been done to calculate GHG emissions with uncertainty analysis. This study estimates GHG emissions and their uncertainties, and also identifies major uncertainty contributors for each method.     

MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

添加炭基材料对蔬菜废物好氧堆肥进程和腐熟度的影响

以蔬菜废弃物辣椒秸秆和树叶为堆肥原料(CK),采用密闭式好氧堆肥工艺,研究了添加5%木本泥炭(T1)、5%活性炭(T2)和10%木本泥炭(T3)等炭基材料对堆肥p H、EC、CO2累积量、物料损失率、T值、C/N和发芽率指数的影响。结果显示,T2处理的p H在60 d后维持在8~9之间;EC值随着堆肥进行呈现先下降后升高再下降的趋势,最终CK、T1、T2和T3处理的EC值(m S/cm)分别降低了1.02、0.76、0.33和0.48;T2和T3处理的CO2累积量一直高于其他处理;所有处理的物料损失率均在20%以上;4个处理堆肥产品的T值分别为0.56、0.65、0.68和0.69;堆肥产品的发芽率指数分别为63.2%、69.3%、93.5%和86.1%。T值和发芽率指数显示T2和T3处理达到了腐熟阶段。结果表明,在蔬菜堆肥处理中添加炭基材料可改善堆肥产品的理化性质,加速堆肥物料的分解,有效地缩短堆肥周期和提高堆肥产品的腐熟度。