南京八卦洲农用地表层土壤重金属分布特征及风险评价

为查明南京八卦洲土壤重金属污染物类型及其影响范围,于2017年12月在洲内采集了471个表层土壤样品,测定了pH及As、Cd、Cr、Cu、Hg、Ni、Pb、Zn等8种重金属元素浓度,采用单因子指数法、内梅罗综合指数法和潜在生态危害指数法进行了污染风险评价。研究结果表明:As、Cd、Cr、Cu、Hg、Ni、Pb和Zn平均浓度分别为10.66、0.32、86.74、43.25、0.10、40.34、33.50和108.33 mg·kg-1,除As、Hg元素外,其余6种元素均超过南京市背景值,出现大范围的富集;Cd元素为研究区主要污染物,绝大部分为Ⅱ级轻微污染,均分布于八卦洲服务区附近的中、酸性土覆盖区,需做好安全利用措施。从全区来看研究区大部分农用地土壤处于安全生产级别,仅有少部分区域处于Ⅱ级和Ⅲ级风险水平,总体上潜在生态危害较低。     

水体及沉积物氮磷水平对附植藻类的影响

为了探讨湖泊富营养化过程中沉积物及水体氮、磷浓度对附植藻类的影响,通过室内模拟实验,研究了水体及沉积物氮、磷升高对苦草(Vallisnerianatans(Lour.) Hara)上附植藻类生长、群落组成及其体内氮、磷含量的影响.结果表明,在实验条件下,随着水中氮、磷含量升高,附植藻类生物量及附植藻类氮、磷含量均呈极显著增加(p0.01).随着水体可获得的氮、磷浓度升高,附植藻类的相对丰度有所变化,舟形藻(Navicula)、小球藻(Chlorella)及微囊藻(Microcystis)相对丰度随着氮、磷水平的升高而下降,直链藻(Melosira)则相反,但舟形藻、直链藻、微囊藻、小环藻(Cyclotella)和小球藻均为群落的优势属种.沉积物氮、磷含量升高对附植藻类生物量、优势种丰度及群落氮、磷含量影响较小,均未达到显著水平(p0.05).在实验条件下,沉积物氮、磷含量对附植藻类影响不大,而水体氮、磷浓度升高显著地促进了附植藻类生长.研究结果也为解释富营养化湖泊沉水植物衰退及消亡提供了一定的科学依据.     

表面活性剂增强修复地下水中PCE的砂箱实验及模拟

在石英砂充填的二维砂箱中开展表面活性剂（Tween 80）冲洗四氯乙烯（PCE）的修复实验,基于图像分析技术监测不同污染源区结构条件下NAPL相的去除过程.由于实验条件限制,实验中缺乏溶解相浓度数据.为此进一步基于UTCHEM数值模拟方法来理解NAPL相和溶解态之间的质量传输过程,并探讨表面活性剂浓度、注入速率等因素对修复效率的影响.综合砂箱实验和数值模拟结果表明：介质均质和非均质条件下会形成不同类型DNAPL污染源区结构,表现为离散状PCE与池状PCE体积比（GTP）差异.由于离散状污染物与表面活性剂的接触面积更大,更易被优先去除;初始GTP值越高,污染物的修复速率和修复效率也越高.增大表面活性剂浓度或提高表面活性剂的注入速率,虽然能提高DNAPL的修复速率,但会明显降低表面活性剂的修复效率,实验过程中修复效率降幅可达93%.线性驱动溶解模型可以有效地模拟表面活性剂修复DNAPLs过程,基于数值模拟方法选择合适的表面活性剂配比可有效的节省实际污染场址修复经费和时间成本.     

某型飞机外翼5—8肋损伤原因分析及修复探讨

目的 分析某型飞机外翼5—8肋油箱区结构不同程度损伤的原因,制定修复方案。方法采用受载分析、有限元仿真计算、静力试验数据分析等强度计算方法分析损伤产生的原因,采用扫描电子显微镜和光学显微镜对磨痕形貌进行观测等失效分析,对损伤结构件开展失效模式分析,根据损伤原因及失效模式制定科学简便的修复方案,同时对损伤长桁采取的修补措施进行强度校核。结果 通过对外翼油箱充压破坏理论分析、有限元仿真计算、静力试验数据反推,并结合飞机实际损伤情况,得出油箱破坏理论分析危险薄弱部位与真实破坏情况一致的结论。有限元仿真计算最危险结构部位与实际结构首先发生破坏部位吻合,可作为深入制定修复方案及推测实际加载压力的依据。通过静力试验数据反推、结构实际损伤及有限元仿真计算结论得出,外翼5—8肋结构出现损伤时油箱施加压力约0.5 MPa,针对损伤制定了更换外翼油箱内部第5—8肋损伤结构和贴补加强损伤长桁的修理方案,经结构强度校核,满足设计要求。结论 分析认为外翼5—8肋油箱区结构损伤原因为油箱压力超过设计值导致结构过载断裂,采用贴补加强修理损伤长桁和更换第5—8肋损伤结构的修复方案能够满足强度设计要求,可指导同类飞机类似结构损伤故障的原因分析和修理,提醒同类飞机维修人员在飞机维护时应关注外翼油箱压力超压问题。     

Application of cryofocusing hydride generation and atomic fluorescence detection for dissolved mercury species determination in natural water samples

The concentration levels of mercury (Hg) species in natural water samples are usually low. Consequently, accurate analysis with low detection limits is still a major problem. In this work, a method was applied for the simultaneous direct determination of dissolved mercury species in water samples by on-line hydride generation (HG), cryogenic trapping (CT), gas chromatography (GC) and detection by atomic fluorescence spectrometry (AFS). The suitability of the method for real samples with different organic matter and chloride contents was evaluated by recovery experiments in synthetic and natural spiked water samples. The HG method was compared with other current available methods for mercury analysis with respect to the different fraction of mercury analysed, i.e. 'reactive', 'reducible' or total. HG derivatization and SnCl2 reduction (with and without previous oxidation with BrCl) were applied to synthetic and natural (spiked and non-spiked) water samples. The influence of chloride and dissolved organic matter concentrations was studied. The results suggest that the HG procedure is suitable for the simultaneous determination of Hg2+ and MeHg+ in surface water samples. Inorganic mercury analysed by HG (i.e. reducible) is close to the total inorganic mercury.     

Speciation of arsenic using solid phase extraction cartridges

Various solid phase extraction (SPE) cartridges were investigated for speciation of arsenite [As(III)], arsenate [As(v)], monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA). Cartridges containing different types of sorbent materials were tested for arsenic retention and elution characteristics. Alumina cartridges were found to completely retain all the four target arsenic species, and are suitable for removal and preconcentration purposes. For speciation analysis, different arsenic species were separated on the basis of their selective retention on and elution from specific cartridges. DMA was retained on a resin-based strong cation exchange cartridge and eluted with 1.0 M HCl. MMA and As(v) were both retained on a silica-based strong anion exchange cartridge and sequentially eluted with 60 mM acetic acid (for MMA) and 1.0 M HCl [for As(v)]. As(III) was not retained on either cartridge and remained in solution. Arsenic species in solution and those eluted from the cartridges were subsequently quantified by using flow injection with hydride generation atomic fluorescence spectrometry (FI-HGAFS) and hydride generation atomic absorption spectrometry (FI-HGAAS). A detection limit of 0.05 microg L(-1) arsenic in water sample was achieved using HGAFS. An application of the method was demonstrated at a drinking water treatment facility. As(III) and As(v) species were determined in water at various stages of treatment. The method is suitable for routine determination of trace levels of arsenic in drinking water to comply with more stringent environmental regulations.     

Development of an ombrotrophic peat bog (low ash) reference material for the determination of elemental concentrations

Given the increasing interest in using peat bogs as archives of atmospheric metal deposition, the lack of validated sample preparation methods and suitable certified reference materials has hindered not only the quality assurance of the generated analytical data but also the interpretation and comparison of peat core metal profiles from different laboratories in the international community. Reference materials play an important role in the evaluation of the accuracy of analytical results and are essential parts of good laboratory practice. An ombrotrophic peat bog reference material has been developed by 14 laboratories from nine countries in an inter-laboratory comparison between February and October 2002. The material has been characterised for both acid-extractable and total concentrations of a range of elements, including Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Na, Ni, P, Pb, Ti, V and Zn. The steps involved in the production of the reference material (i.e. collection and preparation, homogeneity and stability studies, and certification) are described in detail.     

Using improved neural network model to analyze RSP,NOx and NO2 levels in urban air in Mong Kok,Hong Kong

As the health impact of air pollutants existing in ambient addresses much attention in recent years, forecasting of airpollutant parameters becomes an important and popular topic inenvironmental science. Airborne pollution is a serious, and willbe a major problem in Hong Kong within the next few years. InHong Kong, Respirable Suspended Particulate (RSP) and NitrogenOxides NO_x and NO₂ are major air pollutants due to thedominant diesel fuel usage by public transportation and heavyvehicles. Hence, the investigation and prediction of the influence and the tendency of these pollutants are ofsignificance to public and the city image. The multi-layerperceptron (MLP) neural network is regarded as a reliable andcost-effective method to achieve such tasks. The works presentedhere involve developing an improved neural network model, whichcombines the principal component analysis (PCA) technique and theradial basis function (RBF) network, and forecasting thepollutant levels and tendencies based in the recorded data. Inthe study, the PCA is firstly used to reduce and orthogonalizethe original input variables (data), these treated variables arethen used as new input vectors in RBF neural network modelestablished for forecasting the pollutant tendencies. Comparingwith the general neural network models, the proposed modelpossesses simpler network architecture, faster training speed,and more satisfactory predicting performance. This improvedmodel is evaluated by using hourly time series of RSP, NO_x and NO₂ concentrations collected at Mong Kok Roadside Gaseous Monitory Station in Hong Kong during the year 2000. By comparing the predicted RSP, NO_x and NO₂ concentrationswith the actual data of these pollutants recorded at the monitorystation, the effectiveness of the proposed model has been proven.Therefore, in authors' opinion, the model presented in the paper is a potential tool in forecasting air quality parameters and hasadvantages over the traditional neural network methods.     

Conservation and management applications of the REEF volunteer fish monitoring program

The REEF Fish Survey Project is a volunteer fish monitoring program developed by the Reef Environmental Education Foundation (REEF). REEF volunteers collect fish distribution and abundance data using a standardized visual method during regular diving and snorkeling activities. Survey data are recorded on preprinted data sheets that are returned to REEF and optically digitized. Data are housed in a publicly accessible database on REEF's Web site (http: //www.reef.org). Since the project's inception in 1993, over 40,000 surveys have been conducted in the coastal waters of North America, tropical western Atlantic, Gulf of California and Hawaii. The Fish Survey Project has been incorporated into existing monitoring programs through partnerships with government agencies, scientists, conservation organizations, and private institutions. REEF's partners benefit from the educational value and increased stewardship resulting from volunteer data collection. Applications of the data include an evaluation of fish/habitat interactions in the Florida Keys National Marine Sanctuary, the development of a multi-species trend analysis method to identify sites of management concern, assessment of the current distribution of species, status reports on fish assemblages of marine parks, and the evaluation of no-take zones in the Florida Keys. REEF's collaboration with a variety of partners, combined with the Fish Survey Project's standardized census method and database management system, has resulted in a successful citizen science monitoring program.     

Measurements of fractionated gaseous mercury concentrations over northwestern and central Europe, 1995-99

Although it makes up only a few per cent. of total gaseous mercury (TGM) in the atmosphere, the fraction of oxidised (divalent) mercury plays a major role in the biogeochemical cycle of mercury due to its high affinity for water and surfaces. Quantitative knowledge of this fraction present in mixing ratios in the parts-per-10(15) (ppq) range is currently very scarce. This work is based on approximately 220 data for divalent gaseous mercury (DGM) collected during 1995-99 in ambient air. Over the course of the measurements, the sampling and analytical methods were modified and improved. This is described here in detail and includes transition from wet leaching and reduction procedures to thermo-reductive desorption, the use of annular as well as tubular denuders and adoption of an automated sampling system. The concentration of DGM exhibited a strong seasonal behaviour in contrast to atomic gaseous mercury, with low values in winter and maximum values in summer. The DGM/TGM ratios were frequently found to be below the detection limit (< or = 1%) and in the range 1-5%. A trend of diurnal DGM patterns was observed and implies photolytically induced sources. Scavenging of DGM during rain events was also noticed.