前混合式磨料射流系统的容积效应及有关安全问题

前混合式磨料射流系统具有明显的容积效应.通常情况下,系统在停止工作压力降低时,磨料罐将排出约1L的浆液,在长5m以上的管路中淤积;重新工作时,将造成喷嘴和管路的严重磨损,甚至造成堵塞,使系统不能正常工作.为此,笔者提出了一种新型的射流发生系统,改善系统的容积效应,在其停止工作时,采用了磨料罐从上方排出清水以降低系统压力方法,改善磨料大量涌出和管路淤积现象,同时也对管接头等磨蚀引起的有关安全问题进行了讨论.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.     

Gender,age and subject matter: impact on teachers’ ecological values

By means of environmental education, teachers are supposed to intervene in pupils’ awareness and concern of environmental issues. Teachers’ environmental attitudes, however, have rarely been studied. We analysed 367 German pre- and in-service teachers’ environmental attitudes for their structure and socio-economic correlates within the frame of a European project. Thus, we retrieved for adults the two-dimensional model of ecological values (2-MEV) presented for adolescents by Bogner and Wiseman (Sci Educ Int 15(1):27–48, 2004). For the two domains, Preservation and Utilisation, the psychometric structure was confirmed and discriminative correlations with age, gender and teaching subject were unveiled. Further research is needed to deduce the implications for teaching practice.     

Magnesium-rich minerals in sediment and suspended particulates of South Florida water bodies: implications for turbidity

Fine sediments in shallow water bodies such as Lake Okeechobee are prone to resuspension. Predominantly inorganic "mud" sediment that covers approximately 670 km2 of the lake has been recognized as a persistent source of turbidity. The objective of this study was to determine if mineral components of sediments in Lake Okeechobee and water conveyances of the northern Everglades also occur as suspended sediment and hence constitute a potential abiotic contributor to turbidity. Sediment samples were collected from nine stations within the lake and eight locations north of Water Conservation Area 2A in the Everglades. Water samples were also collected at selected locations. The silt and clay mineralogy of sediment and suspended particles was determined using X-ray diffraction, thermogravimetry, scanning-electron microscopy, energy-dispersive X-ray elemental microanalysis, and high-resolution transmission-electron microscopy. Clay fractions of the lake sediment contained the Mg silicate minerals sepiolite and palygorskite, along with smectite, dolomite, calcite, and kaolinite. Sediment silt fractions were dominated by carbonates and/or quartz, with smaller amounts of Ca phosphates and sepiolite. Mineralogy of the mud sediment was similar to that reported for geologic phosphate deposits. This suggests that the mud sediment might have accumulated by stream transport of minerals from these deposits. Suspended solids and mud-sediment mineralogy were similar, except that smectite was more abundant in suspended solids. Everglade samples also contained Mg-rich minerals. The small size, low density, and fibrous or platy nature of the prevalent mud sediment minerals make them an abiotic, hydrodynamically sensitive source of persistent turbidity in a shallow lake. Mitigation efforts focused exclusively on P-induced biogeochemical processes do not address the origin or effects of these minerals. Ecological management issues such as turbidity control, P retention, geologic P input, and suitability of dredging are related to mud-sediment properties and provenance.     

浅析墨菲定律及海因里希法则对控制事故的作用

通过对墨菲定律及海因里希法则的分析,得出重视小概率事件和控制未遂事故的作用,可提高企业安全管理水平,达到预防和控制事故的目的。     

烟气脱硝技术及在我国的应用

氮氧化物气体是危害最大、最难处理的大气污染物之一。随着经济的发展,有效控制燃煤造成的大气污染已经刻不容缓,特别是控制燃煤过程中的氮氧化物,烟气脱硝技术显得相当重要。本文分析了几种常用的烟气脱硝技术（选择性催化还原脱硝技术、选择性非催化还原脱硝技术、碱性溶液吸收法和等离子体活化法等）的原理、技术特点以及在我国的应用情况。     

Dimensional analysis and scaling in mechanical mixing for fabrication of metal matrix nanocomposites

For a successful enhancement of mechanical properties of metal matrix nanocomposites, a homogeneous nanoparticle dispersion and distribution in the solidified metal is required. Mechanical mixing can be used for initial break-up of agglomerates, and its study can be simplified with dimensional analysis. Using this technique, mixing time and vortex height were assessed while varying fluid properties, impeller angle, and angular speed. Three relevant dimensionless numbers were recognized: the Reynolds (Re), Froude and Galilei (Ga) numbers. Based on blade and impeller shaft angles, a modified Froude number (Fr*) was defined. These parameters were calculated experimentally, varying angular speed from 200 to 1000 rpm for three different impeller angles: 0°, 15° and 30°. This procedure was performed with three fluids: water, and two aqueous glycerin solutions (25% and 50% by volume). Digital images were taken and processed to measure vortex height. Mixing time was measured for water at 0° impeller angle, angular speed ranging from 200 to 1200 rpm. Results showed an optimal dimensionless mixing time with respect to Re. A linear relationship was found between dimensionless vortex height and Fr*. The first had a second order polynomial relationship with the product ReFr*, regardless of impeller angle. This relationship, together with the Ga, specific for each fluid, allows scaling the results to other fluids such as molten pure aluminum. This study allows experimenting in simpler systems that involve transparent fluids, room temperature and low cost, to then elaborate a prediction of vortex height in fluids where measurements are difficult and costly, such as molten metals.