Sediments used in this study were collected from different depths of eight sites in East China Sea in November 2002. The levels and distribution patterns of the selected organochlorine pesticides (OCPs=p,p'-DDT, o,p'-DDT, p,p'-DDE, p,p'-DDD, alpha-, beta-, gamma- and delta-HCH) in samples were investigated by the technique of sonication extraction followed by the analysis of gas chromatography (GC) coupled with a micro-electron capture detector (muECD). The concentrations of SigmaHCH and SigmaDDT in the surface sediments were in the range of <0.05-1.45 ng/g (mean 0.76 ng/g), <0.06-6.04 ng/g (mean 3.05 ng/g) based on dry weight (dw), respectively. In the vertical distributions, the SigmaHCH and SigmaDDT were in the range of <0.05-2.52 ng/g, <0.06-10.94 ng/g dw, respectively. Residues of OCPs varied significantly with different sampling sites. SigmaDDT in the surface sediments was correlated well with total organic carbon (TOC) content (r2=0.71), while SigmaHCH showed no obvious correlation. The distribution showed that the sediments from the vicinity estuary or near shore had higher TOC contents, and higher OCPs concentrations. The contamination record indicated an extensive use of OCPs in the catchments from Yangtze River in the past might greatly affect the OCP residues. 相似文献
A simple online headspace solid-phase microextraction (HS-SPME) coupled with the gas chromatography-mass spectrometry (GC-MS) method was developed for simultaneous determination of trace amounts of nine estrogenic odorant alkylphenols and chlorophenols and their derivatives in water samples. The extraction conditions of HS-SPME were optimized including fiber selection, extraction temperature, extraction time, and salt concentration. Results showed that divinylbenzene/Carboxen/polydimethylsiloxane (DVB/CAR/PDMS) fiber was the most appropriate one among the three selected commercial fibers, and the optimal extraction temperature, time, and salt concentration were 70 °C, 30 min, and 0.25 g/mL, respectively. The developed method was validated and showed good linearity (R2?>?0.989), low limit of detection (LOD, 0.002–0.5 μg/L), and excellent recoveries (76–126 %) with low relative standard deviation (RSD, 0.7–12.9 %). The developed method was finally applied to two surface water samples and some of these target compounds were detected. All these detected compounds were below their odor thresholds, except for 2,4,6-TCAS and 2,4,6-TBAS wherein their concentrations were near their odor thresholds. However, in the two surface water samples, these detected compounds contributed to a certain amount of estrogenicity, which seemed to suggest that more attention should be paid to the issue of estrogenicity rather than to the odor problem. 相似文献
The present study aimed to improve the performance of microbial fuel cells (MFCs) by using an intermittent connection period without power output. Connecting two MFCs in parallel improved the voltage output of both MFCs until the voltage stabilized. Electric energy was accumulated in two MFCs containing heavy metal ions copper, zinc, and cadmium as electron acceptors by connection in parallel for several hours. The system was then switched to discharge mode with single MFCs with a 1000-Ω resistor connected between anode and cathode. This method successfully achieved highly efficient removal of heavy metal ions. Even when the anolyte was run in sequencing batch mode, the insufficient voltage and power needed to recover heavy metals from the cathode of MFCs can be complemented by the developed method. The average removal ratio of heavy metal ions in sequencing batch mode was 67 % after 10 h. When the discharge time was 20 h, the removal ratios of zinc, copper, and cadmium were 91.5, 86.7, and 83.57 %, respectively; the average removal ratio of these ions after 20 h was only 52.1 % for the control group. Therefore, the average removal efficiency of heavy metal ions increased by 1.75 times using the electrons stored from the bacteria under the open-circuit conditions in parallel mode. Electrochemical impedance data showed that the anode had lower solution resistance and polarization resistance in the parallel stage than as a single MFC, and capacitance increased with the length of time in parallel.