A new approach for calculating the relative risk level of pesticides

The following paper describes a new, easier to use approach to the calculation of relative risk levels of alternative pesticides. An insect, a plant disease, and a weed were selected for describing the application procedure of a new ranking method that is based on the intrinsic properties of pesticides rather than on the processes that occur both on land and in water after they are applied to soil. The approach is based on the Toxicity-Human health-Persistency (THP) Hazard Rating System, and a consumption factor is added to the method in order to calculate the environmental risk of pesticides. The available substitute pesticides are ranked in terms of their relative risk levels from lowest to highest in order of magnitude difference. Such a ranking method may be used as a practical quantitative tool to generate significant findings aiding in the selection of the most environmentally friendly substitute against a certain pest, especially in developing countries that still face the misuse and/or unconscious use of pesticides.     

Evaluation of the sensitivity of marine microalgal strains to the heavy metals, Cu, As, Sb, Pb and Cd

The sensitivity of nine marine microalgal species (consisting of five divisions and seven genera) to the five heavy metals, Cu(II), As(V), Sb(III), Pb(II) and Cd(II) was studied by using a fluorometric growth-inhibition assay with 96-well microplates. The algal strains studied were Cylindrotheca sp. and the LPP group that respectively characterize aggregating and filamentous types, and Chlorococcum littorale, Chlorococcum sp., Isochrysis galbana, Tetraselmis tetrathele, Heterocapsa sp., Synechococcus sp. and Prasinococcus sp. for types that occur as single cells. A good linear relationship was observed between the chlorophyll a concentration and intensity of chlorophyll fluorescence (485-nm excitation filter and 645-nm emission filter) when the chlorophyll a concentration was within the range of 0.10-5.0 microg ml(-1). A starting cell concentration of 0.10 or 0.25 microg Chl a ml(-1) was therefore selected. In accordance with OECD 201 standard procedures, the IC(50) value (concentration of a metal producing 50% growth inhibition relative to the control) was determined 72 h after adding a heavy metal by using the biomass integral. The microplate toxicity test used in this study is considered to be applicable to diverse algae, not only enumerating species but also hardly enumerating ones.     

Accumulation and release of 241Am by a macrophyte of the Yenisei River (Elodea canadensis)

The source of radioactive contamination of the Yenisei River floodplain, including contamination with transuranic elements, is the Mining-and-Chemical Combine of the Russian Ministry of Atomic Energy, which has for many years been producing weapons-grade plutonium. Transuranic elements have been detected not only in the soil and sediment of the river but also in the biomass of aquatic plants. This work is an investigation of accumulation and release of 241Am by a submerged macrophyte of the Yenisei River (Elodea canadensis) in laboratory experiments. In 2000-2003, laboratory experiments were carried out with biomass of E. canadensis Mich. and filtered river water. The samples were collected from the Yenisei River upstream of the discharge of the Combine's radioactive effluent. The experiments showed that 241Am is accumulated by Elodea biomass: the activity concentration of 241Am can reach 3280+/-240 Bq/g, with the concentration factor for 241Am 16 600+/-2200l/kg. Results of chemical fractionation have proved that in the course of 241Am accumulation by Elodea biomass, 241Am tightly bound to biomass increases from 11% to 27% of the total 241Am in the biomass. Release of 241Am from the decaying Elodea biomass has been evaluated experimentally. By the end of the experiment (lasting up to 127 days), the Elodea plants had lost up to 65% of their initial 241Am activity and the rate of 241Am release into the water environment reached 23 Bq/day.     

241Am, 137Cs, Sr and Pb uptake by tobacco as influenced by application of Fe chelators to soil

To determine the potential for phytoextraction of 241Am and other contaminants from soil, accumulation of 241Am, 137Cs, Sr, Fe, Al, Pb, and Mg by tobacco was determined for soil applications of two concentrations of ethylenediaminetetraacetic acid (EDTA), citric acid, and ascorbic acid. In tobacco receiving EDTA at 3.1 mmol/kg of soil, 241Am content of plants averaged 15 Bq/kg (ranging up to 26 Bq/kg) while Fe concentrations became constant at 4.5 mmol/kg. Soil treatment with 18.8 mmol/kg EDTA resulted in average 241Am concentrations of 29 Bq/kg (19 times higher than controls). Uptake of Pb was similar to 241Am. In these samples, Fe increased to a maximum of almost 18 mmol/kg and 241Am content increased linearly with both Fe and Al. Plants receiving ascorbic and citric acids took up smaller quantities of 241Am, Pb, and Fe, even though these reagents were able to elute about as much Fe from the soil as EDTA. Synchrotron microbeam X-ray fluorescence (SXRF) was used to determine radial distributions of elements in roots and stems with and without EDTA treatment. SXRF maps indicate differences in behavior between Fe and Pb that are consistent with the bulk plant observations and provide insight into changes in metal content of the roots in the presence of EDTA.     

Multi-elemental EDXRF mapping of polluted soil from former horticultural land

The distribution of major and trace elements was systematically investigated by use of energy dispersive X-ray fluorescence spectrometry (EDXRF) on a former horticultural soil. The purpose of the study was to combine mapping of soil element concentration levels with multivariate statistics for characterisation of soil metal pollution in relation to previous and present land use. A 1-ha study site was chosen from a former horticulture where a previous preliminary survey indicated increased concentration levels of toxic elements. The soil was sampled from the top 20 cm of the soil surface in a 10 x 10-m grid-like pattern covering the 1-ha study area. In addition, three soil profiles were studied. The elemental composition of the soil samples was investigated by EDXRF while the composition of aqueous soil extracts was determined by total reflection X-ray fluorescence spectrometry (TXRF). Based on mapping and multivariate statistically analysis of the data obtained by EDXRF, most elements were found in almost constant concentration levels in the top soil throughout the investigated site. However, the contents of the toxic elements Zn, Cu, As, and Pb were found to vary significantly within the area. Hence, the samples with high accumulations of As also contained relatively high amounts of Zn, Cu, and Pb, which indicates that toxic-element-containing pesticides have been applied to the soil surface in the area of the former green houses at the study site. The Pb/As mass ratio in the soil indicates that PbHAsO3 was the preferential lead arsenate used for pest management at the investigated site, while Cu as Bordeaux liquid (CuSO4) and Zn were applied to minimize the leaf damaging effect from the former compounds. Calculations indicated that As annually was applied to the soil in the former greenhouses in doses up to 4 kg As/ha while Pb had been annually applied in doses up to 12 kg Pb/ha. The enrichment of Zn, Cu, As and Pb was greatest in the top 20 cm of the soil and no anthropogenic enrichment of these elements occurred below a depth of 50 cm, indicating that the toxic elements are rather immobile in this soil. The results of this investigation suggest that EDXRF used in combination with multivariate statistics is a strong tool for multi-element mapping of elemental contents, sources and mobility in the terrestrial environment.     

Colonization of surfaces by phenolic compounds utilizing microorganisms

The aim of the present study is to determine optimal adhesive interaction of phenolic compounds utilizing Candida maltosa and Rhodococcus erythropolis when adhering to kaolin, silicone, synthetic foil (Steriking R40) and fluorinated silicones, comparing cell and support surface hydrophobicity. In parallel, the interfering effect of detergents was investigated. Data obtained show that the less hydrophobic supports display high initial cell adhesion when contacted with the cell type with a lower surface hydrophobicity (yeast cell) but most stable yeast biofilms are those formed on highly hydrophobic fluorinated silicones. On the other hand, support hydrophobicity has no effect on bacterial cell detachment; however, bacterial biofilms are denser when growing on more hydrophobic supports. Both detergents interfere (independently on the cell type) with the early and late phases of biofilm development.     

Modelling and experimental studies on the transfer of radionuclides to fruit

Although fruit is an important component of the diet, the extent to which it contributes to radiological exposure remains unclear, partially as a consequence of uncertainties in models and data used to assess transfer of radionuclides in the food chain. A Fruits Working Group operated as part of the IAEA BIOMASS (BIOsphere Modelling and ASSessment) programme from 1997 to 2000, with the aim of improving the robustness of the models that are used for radiological assessment. The Group completed a number of modelling and experimental activities including: (i) a review of experimental, field and modelling information on the transfer of radionuclides to fruit; (ii) discussion of recently completed or ongoing experimental studies; (iii) development of a database on the transfer of radionuclides to fruit; (iv) development of a conceptual model for fruit and (v) two model intercomparison studies and a model validation study. The Group achieved significant advances in understanding the processes involved in transfer of radionuclides to fruit. The work demonstrated that further experimental and modelling studies are required to ensure that the current generation of models can be applied to a wide range of scenarios.     

The prediction of safe lifting behavior: an application of the theory of planned behavior

PROBLEM: Injuries resulting from lifting are costly, and create significant pain and discomfort. While engineering controls are the most effective means of reducing risks, most organizations continue to rely on manual lifting techniques. The problem, however, is that the use of safe-lifting techniques is inconsistent and managers have a difficult time motivating use of these techniques. Consequently, it is important to understand the factors driving safe-lifting behaviors. METHODS: This study used a survey to apply the theory of planned behavior (Ajzen., I., 1991. The theory of planned behavior. Organization Behavior and Human Processes, 50, 179-211) to safe-lifting among 136 materials management employees at a heavy manufacturing organization. Structural equation modeling and factor analysis were employed to analyze relationships among constructs. RESULTS: Results revealed that perceived behavioral control and intention were the strongest predictors of safe-lifting behavior. Subjective norms, to a lesser degree, were also important influences on intention. Attitudes did not surface as effective direct predictors of safe-lifting behavior, but did affect behavior and intent via mediating factors (subjective norms and perceived behavioral control). Finally, the theory of planned behavior was supported as an effective model explaining safe-lifting behavior, and had potential application for many other safety-related behaviors. IMPACT ON INDUSTRY: Results from this study emphasize the importance of perceived behavioral control as a factor associated with safety-related behavior.     

Increase of the purification efficiency of biofilters by the use of a complementary ionisation step

The biofilter and the ionisation system are two oxidative treatment techniques for purification of waste gas streams with low concentrations of volatile organic compounds. In this paper, the authors present the investigations of an ionisation technique aimed at increasing the efficiency of the reduction of the odorant concentration in waste gas streams from biological waste treatment plants. The objective is to enable advanced odour emission reduction and to adjust the existing biofilters to stricter requirements. In a first step, the odorous substances which are major contributors to the overall odorant concentration are identified on basis of various emission data sets with the help of a method of life cycle impact assessment. Thereby limonene, alpha-pinene, ethyl butyrate and dimethyl disulphide were identified as crucial indicators. In a second step, experimental investigations using limonene as a model compound were conducted to gain an understanding of the ionisation process itself and at last for the evaluation of the system.